Sealey AP0618.V4 User manual

1.8M HEAVY-DUTY STEEL WORKBENCH WITH
25MM MDF TOP
MODEL NO: AP0618.V4
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
workbench.
9Wear protective gloves and goggles during assembly.
9Locate workbench in a suitable work area.
9Keep the work area clean, uncluttered and ensure there is adequate lighting.
WARNING! Use workbench on level and solid ground, preferably concrete.
9Keep the workbench clean and tidy in accordance with good workshop practice.
9Keep children and unauthorised persons away from the work area.
8DO NOT use the workbench for any purpose other than that for which it is designed.
8DO NOT use the workbench outdoors.
8DO NOT place the workbench in a damp or wet location or an area where there is condensation.
8DO NOT clean the workbench with any solvents which may damage the surfaces or the protective coating.
8DO NOT move the workbench when there are items placed on it.
8DO NOT overload the workbench.
8DO NOT undertake work on the workbench without the workpiece being adequately secured. Use clamps or a vice (not included but available
from your Sealey stockist), to secure the workpiece.
WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that
may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the
operator.
2. INTRODUCTION
Thick 25mm MDF worktop, used for adding extra rigidity and durability. Powder coated steel frame, for added corrosion resistance. Four
adjustable feet for levelling on uneven ground. Supplied at packed.
3. SPECIFICATION
Model no:.............................................................AP0618.V4
Size (W x D x H): ..................................1800 x 600 x 910mm
Maximum capacity (evenly distributed):....................... 500kg
4. ASSEMBLY
STEP 1: Fit top beams to each leg assemblies using rubber hammer, no xings required.
STEP 2: Fit bottom beams to leg assemblies using rubber hammer, no xings required.
STEP 3: Adjust feet.
.
STEP 4: Fit top, x from underneath using
12 supplied screws.
AP0618.V4 Issue:1 18/03/21
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear protective
gloves Wear goggles
Top beams
Leg
Section
Leg
Section
Bottom beams

Original Language Version
© Jack Sealey Limited
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on [e-mail] or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
AP0618.V4 Issue:1 18/03/21