Sealey AP41104BWS User manual

INSTRUCTIONS FOR:
TOPCHEST 4 DRAWER WIDE RETRO, ROLLCAB 6
DRAWER WIDE RETRO - BLUE WITH WHITE STRIPE
MODEL No's: AP41104BWS, AP41206BWS
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION
1.1. GENERAL SAFETY
 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations
are adhered to when using this product.
 WARNING! Use caution when handling and assembling the metal components. The metal may
have sharp edges or corners, the use of protective gloves is recommended.
 DO NOT open more than one drawer at a time.
DO NOT step on the drawers.
DO NOT let children play with the roll cab or top chest.
Ensure all drawers are fully closed and the self locking catch is activated, before moving the toolbox.
Secure the brakes when rollcab is in the desired position.
 Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep the mounting frame clean and tidy in accordance with good workshop practice.
 DO NOT use in damp work areas.
 WARNING! The warnings, cautions and instructions referred to in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood that common
sense and caution are factors which cannot be built into this product, but must be applied by the
operator.
4. ASSEMBLY
AP41104BWS AP41206BWS Issue: 2(S) - 01/09/15
4.1. Roll Cab Handle Installation.
Position the handle over the holes in the roll cab, attach using the M6 x 12mm hex bolts
 andtightensecurely(g.1).Assemblingthehandlerstwillmakeiteasiertohandlethe
the roll cab.
4.2. Castor Installation.
4.2.1. Laytherollcabcarefullyonitsback,protectingitwithasoftmatplacedontheoor.
4.2.2. Position the two rigid castors at the end opposite the handle.
4.2.3. Insert the M8 x 20mm hex bolts through the washers, then through the castors and into
the base of the roll cab, tightening securely.
4.2.4. Repeat with the two swivel castors on the opposite (handle) end.
4.3. Roll Cab and Top Chest Connection.
4.3.1. Place the top chest onto the roll cab.
4.3.2. Snaptheconnectorsintothesquareholesonthebackofthetopchest(g.3.).
4.3.3. Fasten the connectors with the screws provided.
g.1
g.2
g.3
Original Language Version
© Jack Sealey Limited
AP41104BWS
Extra wide retro styled top chest with modern day functionality. Features 4 drawers with 45kg
ball bearing slides and aluminium trimmed lift latch drawer pulls preventing inadvertent open-
ing. Chest is further enhanced with gas strut supported opening clam shell top providing
additional storage. Retro theme is continued with colour scheme of racing blue with a vinyl
whitestripeandrecessedchromesidehandles.Drawersandtoplidarettedwithdrawer
liners and lock on one key turn. For use with with AP41206BWS Rollcab to make a complete
retro style stack unit.
AP41206BWS
Extra wide retro styled rollcab with modern day functionality. Features 6 drawers with 45kg
ball bearing slides and aluminium trimmed lift latch drawer pulls preventing inadvertant
drawer opening. Retro theme is continued with colour scheme of racing blue with a vinyl
whitestripeandstylishheavydutycasters,twowithbrakes.Alldrawersarettedwithliners
and lock on one key turn. For use with AP41104BWS Topchest to make a complete retro style
stack unit.
Model No: .............................AP41104BWS ............AP41206BWS
Overall Dimensions (W x D x H):.......1080 x 450 x 495mm ......1100 x 460 x 1040mm
Clam Shell Top: ......................960 x 430 x 80mm .....................n/a
Medium Drawer (x4):..................945 x 400 x 60mm .....................n/a
Medium Drawer (x3):.............................. n/a.........945 x 400 x 60mm
Large Drawer (x2): ............................... n/a........945 x 400 x 135mm
Extra Large Drawer (x1): ........................... n/a........945 x 400 x 210mm
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

5. OPERATION
6. MAINTENANCE
5.1. Raise and Release Drawers.
5.1.1. Toopen:liftthedrawerfrontwhilstpullingitout(g.4).
5.1.2. Toclose:shutthedrawerrmlyuntilthelatchengages.
5.1.3. Ifthedrawerdoesnotlatch,thehook(g.4)maybemisalignedorbinding.
Bend the hook gently until it is parallel to the drawer edge and engages when
closed.
5.2. To Remove Drawers
5.2.1. Pull drawer out almost fully.
5.2.2. Locatetheblacklockinglevers(gs.5&6).
5.2.3. Facingthedrawer;liftoneleverup(g.5),andpushtheotherleverdown
 (g.6).
5.2.4. With both levers deployed, the drawer can be pulled out from the slides.
5.3. To Replace Drawers
5.3.1. Extend the drawer runners from the cabinet.
5.3.2. Engage the slides on either side of the drawer carefully into the runners.
5.3.3. Push the drawer closed squarely until the drawer is closed fully, engaging the
locking levers as it goes.
g.4
g.5 g.6
6.1. Lubricate the drawer slides sparingly every six months.
6.2. Clean the metalwork periodically with warm water and a mild detergent.
6.3. Stubborn grease and oil marks can be removed by using a non-abrasive
cleaner.
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
AP41104BWS AP41206BWS Issue: 2(S) - 01/09/15
Original Language Version
© Jack Sealey Limited