Sealey PTB91508 User manual

INSTRUCTIONS FOR:
TOPCHEST 8 DRAWER 915MM HEAVY-DUTY/
ROLLCAB 6 DRAWER 930MM HEAVY-DUTY
MODEL No's: PTB91508, PTB93006
1.1. GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using these units.
Locate the units in a suitable work area.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
WARNING! Use the units on level and solid ground, preferably concrete.
Keep the units clean and tidy in accordance with good workshop practice.
Keep children and unauthorised persons away from the work area.
DO NOT use these units for any purpose other than that for which they are designed.
DO NOT use the units outdoors.
DO NOT place the units in a damp or wet location or an area where there is condensation.
DO NOT clean the units with any solvents which may damage the surfaces or the protective coating.
DO NOT move the units with the drawers out. To avoid tipping, open one drawer at a time and close and secure all drawers whilst
moving.
DO NOT step on the drawers.
Heavy-duty all welded steel construction for strength and durability.
Textured powder coat nish which is solvent and rust resistant.
Ball bearing drawer runners provide superior performance and carry heavier loads, double sets on large drawers.
All drawers have full width sand blasted aluminium lift latch drawer pulls, making easy access and prevention of inadvertent opening when box is being
moved.
Heavy-duty Ø125mm Mag style castors, 2 swivel with toe brakes and 2 xed.
Heavy-duty exterior handles on chest and cabinets.
Topchests feature gas struts on lids for easy opening.
Non-slip drawer liners supplied for all drawers.
Rollcabs supplied with 12mm PVCcoated MDFworktop.
Integral locking system locks all drawers in each unit with the turn of 1 key.
All supplied with 2 keys.
Manufactured to the highest levels of construction to withstand the toughest of workshop/garage conditions.
Model No: PTB91508 Model No: PTB93006
Overall Size (WxDxH) (mm): 915 x 450 x 565 Overall Size (WxDxH) (mm): 930 x 460 x 1050
Medium 1/2 Drawer (x6): 385 x 385 x 60 Medium Drawer (x3): 825 x 385 x 60
Medium Drawer (x2): 825 x 385 x 60 Large Drawer (x2): 825 x 385 x 135
X-Large Drawer (x1): 825 x 385 x 210
Original Language Version
© Jack Sealey Limited
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION
4. ASSEMBLY
4.1. These units are heavy, obtain the help of at least one other person before attempting to unpack them.
4.2. InstallHandle(refertog.1).
4.2.1. Position the holes and attach with the bolts provided. Tighten securely.
Fig.1 Fig.2
PTB91508, PTB93006 | Issue: 3(L) - 06/01/17
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS& CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH ITISINTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
ThankyouforpurchasingaSealeyproduct.Manufacturedtoahighstandard,thisproductwill,ifusedaccordingtothese
instructions,andproperlymaintained,giveyouyearsoftroublefreeperformance.
Refer to instructions Wear protective gloves

Fig.3
Partssupportisavailableforthisproduct.Toobtainalistingand/ordiagram,pleaselogonto:www.sealey.co.uk,
email: [e-mail] or phone: [phone]
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
[e-mail]
SoleUKDistributor,SealeyGroup,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
4.1.2. Whilst holding the levers in these positions pull the drawer out until it is released from the drawer slide.
4.5. ReplaceDrawers(Refertog.3).
4.5.1. Extend the drawer slides from the tool chest/cabinet.
4.5.2. Insert the brackets on each side of the drawer into the slots in the chest/cabinet slides, being careful that they are properly positioned.
4.5.3. Once properly inserted, completely close the drawer to set the slides in their proper positions.
4.6. RaiseandReleaseDrawerHandles(Refertog.4)
4.6.1. These units are equipped with raise and release drawer handles.
4.6.2. To open, lift up the drawer handle, whilst pulling it towards you. To close, shut the drawer rmly, until the latch engages.
4.6.3. If the drawer does not stay closed, the hook may be bent or it may rub against the drawer slides. To x lightly bend the hook until the
drawer will engage in the slide.
4.7. ChestandCabinetConnection (Refertog.5) (OptionPTB91508orPTB915TR)
4.7.1. Take out the work top from on top of the cabinet.
4.7.2. Place the chest on the cabinet.
4.7.3. Attach the connectors and make sure the hook head snaps into the square hole on the back of the chest. Fasten the screws to the
cabinet.
5.1. Lubricate the casters annually with bearing grease.
5.2. Lubricate the slides twice a year.
5.3. Periodically the drawer fronts, drawer trim and other surfaces
should be cleaned with mild detergent and water.
Fig.4
Fig.5
5. MAINTENANCE
EnvironmentalProtection
Recycleunwantedmaterialsinsteadofdisposingofthemaswaste.Alltools,accessoriesandpackagingshouldbe
sorted,takentoarecyclingcentreanddisposedofinamannerwhichiscompatiblewiththeenvironment.
Whentheproductbecomescompletelyunserviceableandrequiresdisposal,drainoffanyfluids(ifapplicable)
intoapprovedcontainersanddisposeoftheproductandthefluidsaccordingtolocalregulations.
4.3. InstallWheels(Rollcabs)(Refertog.2).
4.3.1. Carefully lay rollcab on its back, with a soft mat underneath for protection. Install the two braked casters on the same end as the handle.
4.3.2. Insert the carriage bolts through washers, then through the casters and into the bottom of the cabinet. Tighten securely.
4.3.3. Install the xed wheels on the opposite end to the handle.
4.4. RemoveDrawers(Refertog.3).
4.1.1. Pull drawer out until it is almost fully extended. Push up one black release lever, while pulling down the other hand black release lever.
Original Language Version
© Jack Sealey Limited PTB91508, PTB93006 | Issue: 3(L) - 06/01/17