Sega TARGET BRAVO User manual

IMPORTANT
• Before using this product, read this manual carefully to understand the
contents indicated in this document.
• After reading this manual, be sure to keep it near the product or in a
convenient location for easy reference when needed.
OWNER'S MANUAL 420-0029-00K
TARGET BRAVO: OPERATION GHOST
Sega Amusements Europe Limited.
42 Barwell Business Park, Leatherhead Road, Chessington, Surrey, KT9 2NY. United Kingdom.
Telephone: [phone] Facsimile: [phone]
email: [email protected] Web: http://www.segaarcade.com
Sega Games Co,. Ltd.1-2-12, Haneda, Ota-ku, Tokyo, 144-8531. Japan.
Telephone: [phone] Facsimile: [phone]
sega-games.co.jp
© SEGA
Errors and omissions excepted (E&OE)
1st PRINTING
July 2017 revision 1.00
OPERATOR & SERVICE MANUAL

Indicates that mishandling the product by disregarding this pictograph will cause
severe injury or death.
Indicates that mishandling the product by disregarding this warning will cause a
potentially hazardous situation which can result in death or serious injury.
Indicates that mishandling the product by disregarding this caution will cause a slight
hazardous situation which can result in personal injury and/or material damage.
For the safe usage of the product, the following pictographs are used:
Indicates "HANDLE WITH CARE." In order to protect the human body and equipment, this
display is attached to places where the instruction manual should be referred to.
Indicates a "protective earth terminal." Before operating the equipment, be sure to connect it to the
ground.
(The step may be omitted for products in which a power cable with earth is used.)
•
Perform work in accordance with the instructions herein stated.
Instructions for work are explained by paying attention to the aspect of accident prevention. Failing
to perform work as per the instructions can cause accidents. In the case where only those who have
technical expertise should perform the work to avoid hazardous situation, the instructions herein state
that the site maintenance personnel should perform such work.
Be sure to turn off the power before working on the machine.
To prevent an electric shock, be sure to turn off the power and unplug the power cable before carrying
out any work that requires direct contact with the interior of the product. If the work is to be performed in
the power-on status, the instruction manual herein always states to that effect.
Be sure to ground the earth terminal.
(This is not required in the case where a power cable with earth is used.)
This product is equipped with the earth terminal. When installing the product, connect the earth terminal
to the "accurately gro
unded indoor earth terminal" by using an earth wire. Unless the product is grounded
appropriately, the user can be subject to an electric shock. After performing repair, etc. for the control
equipment, ensure that the earth wire is firmly connected to the control equipment.
Ensure that the power supply used is equipped with an earth leakage breaker. Using a
power supply which is not equipped with the earth leakage breaker can cause a fire when earth leakage
occurs.
Be sure to use fuses which meet the specified rating.
(Only for the machines which use fuses.)
Using fuses exceeding the specified rating can cause a fire and an electric shock.
•
•
•
•
TARGET BRAVO
Before using this product, be sure to read the following
To maintain safety:
To ensure the safe operation of this product, be sure to read the following before usage.
The following instructions are intended for the users, operators and the personnel in charge of the operation of
the product.After carefully reading and sufficiently understanding the warning displays and cautions, handle the
product appropriately. Be sure to keep this manual close to the product or in a convenient place for future
reference.
Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially
hazardous degrees, the terms of DANGER, WARNING, CAUTION, etc. are used. Be sure to understand the
contents of the displays before reading the text

•
Specification changes (removal of equipment, conversion and addition) not
designated by SEGA are not allowed.
The parts of the product include warning labels for safety, covers for personal protection, etc. It is very
hazardous to operate the product by removing parts and/or modifying the circuits. Should doors, lids and
protective parts be damaged or lost, refrain from operating the product, and contact where the product
was purchased from or the office herein stated.
SEGA shall not be held responsible for any accidents, compensation for damage to a third party,
resulting from the specifications not designated by SEGA.
Ensure that the product meets the requirements of appropriate electrical
specifications.
Before installing the product, check for electrical specifications. SEGA products have a nameplate on
which electrical specifications are described.
Ensure that the product is compatible with the power supply
voltage and frequency requirements of the location. Using any electrical specifications different from the
designated specifications can cause a fire and an electric shock.
Install and operate the product in places where appropriate lighting is available,
allowing warning labels to be clearly read.
To ensure safety for the customers, labels and printed instructions describing potentially hazardous
situations are applied to places where accidents can be caused. Ensure that where the product is operated
has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again
immediately. Please place an order with where the product was purchased from or the office herein stated.
When handling the monitor, be very careful. (Applies
only to products with monitors.)
Some of the monitor parts are subject to high tension voltage. Even after turning off the power, some
portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be
performed only by those technical personnel who have knowledge of electricity and technical expertise.
Be sure to adjust the monitor properly.
(Applies only to products with monitors.)
Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the
monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the
customers.
When transporting or reselling this product, be sure to attach this manual to the
product.
•
•
•
•
*
In the case where commercially available monitors and printers are used in this product, onlythe
contents relating to this product are explained herein. Some commercially available equipment
has functions and reactions not stated in this manual. Read this manual together with the
specific
instruction manual of such equipment.
Descriptions herein contained may be subject to improvement changes without notice.
The contents described herein are fully prepared with due care. However, should any question
arise or errors be found, please contact SEGA.
*
*
Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately
after transporting to the location. Nevertheless, an irregular situation may occur during
transportation. Before turning on the power, check the following points to ensure that the product
has been transported in a satisfactory status.
Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet?
Are casters and adjusters damaged?
Do the power supply voltage and frequency requirements meet with those of the location?
Are all wiring connectors correctly and securely connected? Unless connected in the correct way,
connector connections can not be made accurately. Do not insert connectors forcibly.
Do power cables have cuts and dents?
Are all accessories available?
Can all doors and lids be opened with the accessory keys? Can doors and lids be firmly closed?
INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION

INTRODUCTION
This manual is intended to provide detailed descriptions together with all necessary information covering the general
operation ofelectronic assemblies, electromechanical, servicing control, spare parts, etc. for the product,
"TARGET BRAVO: OPERATION G.H.O.S.T."
This manual isintended for the owners, personnel managers incharge of operation ofthis product.
Operate the product after carefully reading and sufficiently understanding the instructions.
In the unlikely event that the product does notfunction correctly, DONOT allow anyone other than a technician
to touch the internal system. Turn off the power tothe machine, making sure tounplug the electrical cord fromthe
outlet, and contact the office listed below orthe point-of-purchase for this product.
Use of this product is unlikely to cause physical injuries or damage to property. However, points that require special
attention are indicated bybold text, thewords "STOP, IMPORTANT or CAUTION” and the symbols below.
Sega Amusements International Limited.
42 Barwell Business Park, Leatherhead Road, Chessington, Surrey, KT9 2NY. United Kingdom.
European Sales: [phone] Facsimile: [phone]
USA Sales:
STS (Spares):
email:
+00 (1) 224 265 4287
[phone]
[e-mail]
Facsimile:
Web:
[phone]
http://www.segaarcade.com
Indicates a warning or caution that, if ignored, may result in the mishandling
of the product and cause faulty operation or damage to the product.
Indicates important information that, if ignored, may result in the mishandling
of the product and cause faulty operation or damage to the product.

Definition of 'Site Maintenence Personnel or Other Qualified Individuals
Parts replacement, maintenance inspections and troubleshooting should be carried out by site maintenance personnel
or other qualified professionals. This manual includes directions for potentially dangerous procedures which should
only be carried out by professionals with the appropriate specialised knowledge.
The site maintenance personnel or other qualified professionals mentioned in this manual are defined as follows:
Site maintenance personnel:
Individuals with experience in maintaining amusement equipment, vending machines, etc., working under the super-
vision of the owner/operator of this product to maintain machines within amusement facilities or similar premises by
carrying out everyday procedures such as assembly, maintenance inspections, and replacement of units/expendable
parts.
Activities to be carried out by site maintenance personnel:
Amusement equipment/vending machine assembly, maintenance inspection and replacement of units/expendable
parts.
Other qualified professionals:
Persons employed by amusement equipment manufacturers, or involved in design, production, testing or mainte-
nance of amusement equipment. The individual should have either graduated from technical school or hold similar
qualifications in electrical/electronics/mechanical engineering.
Activities to be carried out by other qualified professionals:
Amusement equipment/vending machine assembly, repair/adjustment of electrical/electronic/mechanical parts.
Procedures not described in this manual or marked as ‘to be carried out by site
maintenance personnel or other qualified professionals’ should not be carried
out by personnel without the necessary skill or technology. Work carried out by
unqualified persons may cause serious accidents, including electrocution.

Waste of Electrical and Electronic Equipment (WEEE) Statement.
The WEEE (Waste of Electrical and Electronic Equipment) directive places an obligation on all EU based manufac-
turers and importers of Electrical and Electronic Equipment to take back products at the end of their useful life. Sega
Amusements Europe Ltd accepts its responsibility to finance the cost of treatment and recovery of redundant WEEE
in the United Kingdom in accordance with the specified WEEE recycling requirements.
The symbol shown below will be on all products manufactured from 13th August 2005, which indicates this product
must NOT be disposed of with other normal waste. Instead, it is the user’s responsibility to dispose of their waste
equipment by arranging to return it to a designated UK collection point for the correct recycling of waste electrical
and electronic equipment.
For more information about where you can send your waste equipment for recycling contact your local authority of-
fice.
For non-UK users contact your local authority office for information on the recycling of Waste Electrical and Elec-
tronic Equipment.
Battery Recycling Statement.
The EC Directive on Batteries and Accumulators (2006/66/EC) aims to minimise the impact of batteries on the en-
vironment and encourage the recovery of the materials they contain. To achieve increased collection and recycling
of waste batteries, the Directive places ‘producer responsibility’ obligations on manufacturers and importers of
portable, industrial and automotive batteries.
The symbol shown below will be on all equipment fitted with batteries from 26th September 2008 and indicates
they must NOT be disposed of with other normal waste. Instead, it is the user’s responsibility to dispose of used
batteries by arranging to return them to a designated collection point for the correct recycling.
For more information about where you can send your waste batteries for recycling contact your local authority of-
fice.
REGISTERED IN ENGLAND REGISTERED NO. 1711515
REGISTERED OFFICE: BLOCK C 42 BARWELL BUSINESS PARK, CHESSINGTON, SURREY KT9 2NY

•For the IC board circuit inspections, only the use of a logic tester is
recommended. Using a Multi- Tester or General Purpose Tester may result
in damage to IC Circuits.
•Static electricity from your body may damage some electronics devices on
the IC board. Before handling the IC board, touch a grounded metallic
surface so that the static electricity can bedischarged.
•This video gaming cabinet utilises a motorised steering feedback system.
Do not attempt to service this part or any other part in close proximity to the
steering mechanism whilst power is applied.
•Some parts are not designed and manufactured specifically for this
game machine. The manufacturers may discontinue, or change the
specifications of such general-purpose parts. If this is the case, SEGA
cannot repair or replace a failed game machine whether or not a
warranty period hasexpired.
•Do not touch undesignated places. Touching places not designated can
cause electric shock or shortcircuit.
•Whenever any fasteners (e.g. screws, nuts) have been lost, be sure to use
replacement fasteners with proper dimensions as specified in this manual.
If fasteners of any other dimensions are used, it could cause damage
and/or separation of parts that result in secondaryaccidents.
•Specification changes, removal of equipment, conversion and/or
addition, not designated by SEGA are not permitted.
•Failure to observe this may cause a fire or an electric shock.
Noncompliance with this instruction can have a bad influence upon
physical conditions of the players or the onlookers, or result in injury
during play.
•SEGA shall not be held responsible for damage, compensation for
damage to a third party, caused by specification changes not
designated by SEGA.
•Performing work or parts replacements not described in this manual
could result in accidents. If you need to perform any work not listed in this
manual, request work from the office indicated in this manual or the point-
of-purchase, or inquires fordetails.
•Be sure to perform periodic maintenance inspections hereinstated.

CONCERNING THE STICKER DISPLAY
This SEGA product has stickers attached describing the product manufacture No. (Serial No.) andElectrical Specifi-
cations. Italso has a Sticker describing where to contact for repair andfor purchasing parts.
When inquiring about orasking for repairs, mention the Serial No. andName of Machine indicated onthe Sticker.
The Serial Number indicates the product register. Identical machines could have different parts depending onthe date
of production. Also, improvements and modifications might have been madeafter thepublication ofthis manu- al. In
order toensure you order the correct parts, mention the Serial No. when contacting the applicable places.
CONCERNING WARNING DISPLAYS
This SEGA product has warning displays onstickers, labels and/or printed instructions adhered/attached toorin-
corporated in the places where a potentially hazardous situation could arise. The warning displays are intended for
accident prevention for customers andfor avoiding hazardous situations relating tomaintenance and servicing work.
Some portions ofthe cabinet contain high voltage and may cause accidents iftouched. When performing mainte-
nance, be very careful ofthe warning displays. Itisespecially important that any complex repair andreplacement
work not mentioned herein should be performed bythose technical personnel who have knowledge of electricity and
technical expertise.
In order toprevent accidents, caution any customer ignoring the warnings tocease and desist immediately.

2PRECAUTIONS REGARDING INSTALLATION
•Be sure to check the Electrical Specifications. Ensure that this product is
compatible with the location's power supply, voltage, and frequency
requirements. A plate describing Electrical Specifications is attached to the
product. Noncompliance with the Electrical Specifications can cause a fireand
electric shock.
•This product requires a breaker and earth mechanism as part of the location
facilities. Using the product without these can cause a fire and electric shock.
•Ensure that the indoor wiring for the power supply is rated at 15 A or higher (AC
single phase 100 V ~ 120 V area), and 7 A or higher (AC 220 V ~ 240 V area).
Noncompliance with the Electrical Specifications can cause a fire and electric
shock.
•Be sure to use an independent power supply equipped with an earth leakage
breaker. Using a power supply without an earth leakage breaker can cause an
outbreak of fire if a power surgeoccurs.
•Putting many loads on one electrical outlet can cause generation of heat and
a fire resulting from overload.
•When using an extension cord, ensure that the cord is rated at 15 A or higher
(AC 100 V ~ 120 V area) and 7 A or higher (AC 220 V ~ 240 V area). Using a
cord rated lower than the specified rating can cause a fire and electric shock.
LIMITATIONS OF USAGE
•This product is an indoor game machine. Do not install it outside. Even indoors,
avoid installing in places mentioned below so as not to cause a fire, electric
shock, injury and/or malfunction.
•Places subject to rain or water leakage, or places subject to high humidity in
the proximity of an indoor swimming pool and/or shower, etc.
•Places subject to direct sunlight, or places subject to high temperatures in the
proximity of heating units,etc.
•Places filled with inflammable gas or vicinity of highly inflammable/volatile
chemicals or hazardous matter.
•Dusty places.
•Sloped surfaces.
•Places subject to any type of violent impact.
•Vicinity of anti-disaster facilities such as fire exits and fire extinguishers.
•Areas where the temperature exceeds the applicable temperature (ambient
temperature) range of 5 to 30 degreescentigrade.

•To avoid injury, be sure to provide sufficient space by considering the
potentially crowded situation at the installation location. Insufficient installation
space can cause contact, collisions, and/or trouble between customers.
•During daily cleaning, be sure to check the surface of the control unit and other
parts that the player touches with his/her hands for damage, cracks, or loose
screws. If a player uses the machine while it is damaged, cracked, or has a
loose screw, the player may become injured.
Ensure that the screws are not loose and are all present.
Ensure that there is no damage to cable connectors.
Ensure that the buttons (in 3 places) are functioning correctly.
•Check carefully to make sure there are no gaps in the cabinet joints and that
they are not loose. If there are gaps or looseness, players may get their hands
or fingers caught, resulting in an injury.
•Make sure all the doors are locked securely and that they do not rattle. If the
doors are not locked properly or there are gaps or rattling, the players could
get their fingers or hands caught. It could also invitemischief.
•Be sure to perform appropriate adjustment of the LCD. For operation of this
machine, do not leave monitor’s flickering or deviation as is. Failure to observe
this can have a bad influence upon the players’ or the customers’ physical
conditions.
•Inspect for the following items during a trial run. If there is any type of error, use
the Test Mode, etc., to resolve the problem. If you continue use with an error, it
can cause an accident or irreparable partsdamage.
-Is there any strangeness in the operability of the controlunit?
-Is there any improper adjustment of the LCDscreen?
•Prepare a place where players can rest if they feelsick.

2-1 PAYING ATTENTION TO CUSTOMERS
To avoid injury and trouble, be sure to constantly give careful attention to the behaviour and manner of the visitors
and players.
DURING OPERATION (PAYING ATTENTIONTO CUSTOMERS)
•For safety reasons, do not allow any of the following people to play thegame.
-Those who have high blood pressure or a heartproblem.
-Those who have experienced muscle convulsion or loss ofconsciousness
when playing video games, etc.
-Those who have neck or spinal cordproblems.
-Those who are intoxicated or under the influence of drugs.
-Pregnant women.
-Those who are not in goodhealth.
-Those who do not follow the attendant’sinstructions.
-Those who cannot grasp the Control Unit securely because of immobility in
fingers, hands or arms.
-Persons who disregard the product's warningdisplays.
This product is intended for a single player only. Having two or more persons
simultaneously playing this product can result to injury to the player and possible
damage to the product.
•Even players who have never been adversely affected by light stimulus might
experience dizziness or headache depending on their physical condition
when playing the game.
Small children are especially likely to experience these symptoms. Caution
guardians of small children to keep watch on their children during play.
•Instruct those who feel sick during play to have a medicalexamination.
•To avoid injury from falls and electric shocks due to spilled drinks, instructthe
player not to place heavy items or drinks on the product.
•To avoid electric shocks and short circuits, do not allow customers to put
hands and fingers or extraneous matter in the openings of the product or small
openings in or around thedoors.
•To avoid falls and resulting injury, immediately stop the customer from leaning
against or climbing on the product, etc.
•To avoid electric shock and short circuit, do not allow customers to unplug the
power plug without a justifiable reason.
•Instruct the guardians of small children to keep an eye on theirchildren.
Children cannot sense danger. Allowing small children to get near a player
who is playing the game could result in the children being bumped, struck or
knocked down.

•Immediately stop such violent acts as hitting and kicking the product. Such
violent acts can cause parts damage or falling down, resulting in injury due to
fragments and falling down.
Persons other than the player should not be allowed to touch the controls during
play. They may brush against or collide with the controls or the player, possibly
resulting in accidents.
Instruct those who feel sick during play to have a medical examination.
Immediately stop users from leaning or sitting on the control panel. Such acts
can lead to injury or damage to parts or the shape of the cabinet.
Immediately stop users from swinging or reloading the control unit in a violent
manner. Such acts may hurt the user or other people around them.
Playing too close to the cabinet may cause the control unit to hit the cabinet
and cause damage. Make sure that players understand to play at a safe
distance from the cabinet.
Make sure that players understand not to stand too close together when playing
a 2 player game. Swinging the control unit could lead to a player getting hit and
may cause injury.
Instruct players to hold the control unit securely while playing. If the control unit
is dropped, it could cause injury to the player.
Items such as large finger rings can cause injury to the fingers while playing.
Instruct players to remove all accessories that could cause an accident before
playing.
Instruct players that a single control unit is never to be held by 2 or more people
during play. Otherwise there could be dangerous contact or a collision.
•
•
•
•
•
•
•
•
•
The control units for use on 1P side (left side) and 2P side (right side) are different.
Ensure that players do not confuse the right and left side control units when starting
play.
●Players directly hold the control unit with their bare hands so it is recommended
that wet towels (paper towels) be provided.
●Diligently clean the parts that players touch directly to ensure a pleasant game
playing experience.
●Inspect the coin insertion slots to make sure no foreign objects have beeninsert-
ed and that they have not otherwise been tampered with. This will prevent play.

3PRECAUTIONS WHEN MOVING THE MACHINE
•When moving the cabinet, do not grip or push the Reflector Plates. Doing so
could deform or damage the part.
•If moving through a door or place with a low ceiling such as an elevator, you
should take apart the billboard and reflector plates.
•Always disconnect the power cable before moving the product. If it is moved
with the power cable connected, the cable could be damaged, causing fire or
electric shock.
•To move the unit over the floor, pull in the adjusters and have the casters
contact the floor. While moving the unit, be careful that the casters do not roll
over the power cord or the ground wire. If cord or wire is damaged, there could
be electrical shocks and/or shortcircuits.
•When crossing a sloped or stepped area, always have the machine travel
lengthways. Travelling with the machine in a sideways position could result in
the machine falling over onto its side. Always use a minimum of two people
working together plus lifting apparatus to accommodate slopped areas or
stairs.
•To lift up the cabinet, hold it at the bottom at the designated lifting points. If you
hold it anywhere else, the weight of the cabinet could cause damage to parts
or attachments, resulting in injury.
•Do not push the cabinet from the side when moving. Pushing from the side may
result in the cabinet falling over.
•Do not move the cabinet without the side retaining bolts fitted. Doing so may
cause damage and injury.

4 GAME DESCRIPTION
4-1 HOW TO PLAY
When you insert coins, they will be counted in the credit display at the bottom of the screen. When you insert enough
coins for a game, the message at the bottom will change from “INSERT COIN(S)” to “PRESS START BUT- TON,”
and the start buttons on both sides will flash. Up to 24 credits can be counted at once. Coins inserted after 24 credits
are recorded will not be counted or returned. However, the number of coins inserted will be counted in the data display
and the coin meter.
NOTE: The number of credits required for a game can be set in SYSTEM TEST MODE.
Which START button you press determines which side you play on. Once you press the start button, the game be-
gins.
Once the game starts, the video demonstration will play, followed by the 1 title, and then it will go to the actual
game.
4-2 GAME SCREENS
This game has two modes, one is "Mission" and the other is "Wave".
NOTE: Mode Select can be set in Game Assignments. (See 9-3-5>WAVE.)
"Mission" is the story mode. Procced the stages with story,
When you choose the Mission mode, you can select the stages you want to play.
"WAVE" means "time Attack mode". The game was limited by time and no life system.
The game is over when setting stage numbers for a play has finished (See 8-9) to each player.

4-3 RELOADING
When the player fires all ammo remaining, the gun will be empty. The player can then reload the
weapon by aiming it outside the screen. The player can reload this way even if there are stillbul-
lets left.
The gun is also reloaded automatically when the trigger is pulled with no ammo remaining.
However, this type of reload takes longer than a normal reload.
The player can switch shooting mode during gameplay using the shot selector.
4-4 SWITCHING SHOOTING MODE
SHOT SELECTOR
TRIGGER
ACTION BUTTON
The types of shooting mode and their features are as follows.
When shooting mode is switched, the player’s crosshair is changed to the applicable shooting mode crosshair.
FULL AUTOCROSSHAIR 3-ROUND BURST CROSSHAIR SEMI AUTO CROSSHAIR
FULL AUTO Bullets are fired continuously as long as the trigger is held.
You have limited ammunition. The number of rounds remaining is displayed to the side of
the shooting mode. (See 8-2.)
The number of rounds can be increased by scoring critical hits or obtaining items.
3-SHOT BURST Pulling the trigger once fires a burst of 3 rounds in a row.
You have unlimited ammunition.
SEMI AUTO Pulling the trigger once fires 1 shot only.
You have unlimited ammunition.

4-5 STAGE SELECT
A player can select each stage (mission/wave) after mode has selected.
Player can also select new stage if player completed the stage player selected.
Game is over when the all set stages finished.
Mission Wave Time remaining Ranking
4-6 ITEMS
Various items appear when the player shoots item boxes in the background. The player can then
gain the effects of those items by shooting them.
ITEM BOX LIFE RECOVERY FULLAUTOAMMO INCREASE

4-7 EVENTS
Various events occur in the course of the game.
An explanation of the control method for the event will be displayed before the event begins.
Successfully completing events will lead to an increase in the mission success rate (the evalua-
tion displayed after clearing the mission), and the player can earn a higher score.
EVENTS screen
4-8 BATTLES WITH BOSSES
A unique boss awaits the player at the end of each stage.
When the boss begins an attack, a cancel gauge will sometimes appear.
The boss’s attack can be avoided by forcing the cancel gauge down to zero.
BOSS’S CANCEL GAUGE LIFE GAUGE
BOSS BATTLE screen 1

Shooting the boss drains the boss’s LIFE gauge.
Attacking the boss’s weak point drains the boss’s LIFE gauge significantly.
When the boss’s LIFE gauge reaches zero, the boss is defeated.
BOSS’S WEAK POINT PROMPT
BOSS BATTLE screen 2
4-9 GAME OVER
If both players run out of LIFE, the game ends.
MISSION:
If you want to join the game during play, insert coins and press the START button at any time. If there are
enough credits remaining to play, the START button on the side with no one playing flashes continuously.
When all LIFE is lost, the continue message is displayed. If you wish to continue, insert the required num-
ber of coins and press the START button again. If there are enough credits remaining to CONTINUE, you
can join again by pressing the START button.
NOTE: The number of credits required to continue can be set in SYSTEM TEST MODE (See Chap-
ter 10.)
If your total points rank among the top 50 after completing all the stages in the game, you can enter your
name.
WAVE:
1. If you want to join the game during play, insert coins and press the START button at the time you can
join. If there are enough credits remaining to play, the START button on the side with no one playing
flashes continuously. Join the game by pressing the flashing START button.
2. When set stages are completed, the continue message is displayed. If you wish to continue, insert the
required number of coins and press the START button again. If there are enough credits remaining to
CONTINUE, you can join again by pressing the START button.
NOTE: The number of credits required to continue can be set in SYSTEM TEST MODE
3. If your total points rank among the top 50 after completing a stage in the game, you can enter your
name.

4-10 CONTINUE PLAY BONUS
The player receives body armour as a continue play bonus when they choose to continue.
Body armour will take the damage from 1 enemy attack while equipped.
NOTE: This feature can be set in GAME TEST MODE. (See 11-5.)
CONTINUE PLAY BONUS screen CONTINUE PLAY BONUS PROMPT