Sega NAOMI User manual

ee
Tow!
“IW
geBO
6°
ant issanol
-oliw
its
19fLA. clocd2
5
659 elomifl a:
"348918 aps.
Dacidw yligene
-
ZIBOOE 24,
nomdw 2enifiosr
.
.

BEFORE USING THE PRODUCT, se sure 10 revo tHe FoLLowine:
To maintain the safety:
To
ensure
the safe usage of the product, be
sure
to read the following before using the product. The
following instructions
are
intended for the users, operators and the personnel in charge
of
the opera-
tion of the product. After carefully reading and sufficiently understanding the warning displays and
cautions, handle the product appropriately. Be
sure
to
keep this manual nearby the product
or
elsewhere convenient for referring to
it
when necessary.
Herein, explanations which require special attention
are
enclosed with dual lines. Depending
on
the
potentially hazardous degrees, the terms ofDANGER!, WARNING!, CAUTION, etc.
are
used.
Be
sure
to understand the
contents
of the displays before reading the text.
Indicates that mishandling the Indicates that mishandling the
product by disregarding this picto- product by disregarding this
cau-
graph
will
cause
severe
injury
or
tion
will
cause
a
slight hazardous
death. situation which
can
result in per-
DANGER! CAUTION! sonal injury and
or
material dam-
age.
:
Indicates that mishandling the Indicates that mishandling the
product by disregarding this
warn-
product by disregarding this dis-
AN ing
will
cause
apotentially hazard- Eon play
can
cause
the product's intrin-
;
ous
situation which
can
result in sic performance
not
to be obtained,
WARNING! =Geath
or
serious injury. IMPORTANT! resulting in malfunctioning.
For the safe usage of the product, the following pictographs
are
used:
Indicates "HANDLE WITH CARE." In order to protect the human body and equip-
ment, this display is attached to places where the Owner's Manual and
or
Service
Manual should be referred to.
Indicates
a
"Protective Earth Terminal." Before operating the equipment, be
sure
to
connect it to the Ground.
o>
O
Perform work in accordance with the instructions herein stated.
Instructions for work are explained by paying attention to the aspect of accident prevention.
Failing to perform work as per the instructions can cause accidents. In the case where only
those who have technical expertise should perform the work to avoid hazardous situation, the
instructions herein state that the serviceman should perform such work.
O Be sure to turn off power before working on the machine.
To prevent electric shock, be sure to turn off power before starting the work in which the
worker touches the interior of the product. If the work is to be performed in the power-on
status, the Instruction Manual herein always states to that effect.
O
Be
sure
to
ground the Earth Terminal (this, however, is
not
required in the
case
where
a
power cord with earth is used).
This product is equipped with the Earth Terminal. When installing the product, Connect the
Earth Terminal to the "accurately grounded indoor earth terminal" by using
an
earth wire.
Unless the product is grounded appropriately, the
user
can
be subject to electric shock. After
performing repair, etc. for the Control equipment,
ensure
that the Earth Wire is firmly
con-
nected to the Control equipment.
O
Ensure that the Power Supply used is equipped with
an
Earth Leakage Breaker.
This product does
not
incorporate the Earth Leakage Breaker. Using
a
power supply which is
not equipped with the Earth Leakage Breaker can cause afire when earth leakage occurs.
O
Be
sure
to
use
fuses which meet the specified rating. (only for the machines which
use fuses).
Using fuses exceeding the specified rating
can
cause
afire and electric shock.

O. Specification changes (removal of equipment, conversion and addition)
not
designated by SEGA
are
not allowed.
The parts of the product include warning labels for safety,
covers
for personal protection, etc.
It
is very hazardous to operate the product by removing parts and
or
modifying the circuits.
Should doors, lids and protective parts be damaged
or
lost, refrain from operating the product,
and
contact
where the product
was
purchased from
or
the office herein stated.
OEnsure that the product meets the requirements of appropriate Electrical
Specifications.
i
Before installing the product, check for Electrical Specifications. SEGA products have a
nameplate on which Electrical Specifications are described. Ensure that the product is com-
patible with the power supply voltage and frequency requirements of the location. Using any
Electrical Specifications different from the designated Specifications can cause a fire and
electric shock.
OInstall and operate the product in places where appropriate lighting is avail-
able, allowing warning labels to be clearly read.
To ensure safety for the customers, labels and printed instructions describing potentially
hazardous situation
are
applied to places where accidents
can
be caused. Ensure that where
the product is operated has sufficient lighting allowing the warnings
to
be read.
If
any label is
peeled off, apply it again immediately. Please place an order with where the product was
purchased from
or
the office herein stated.
O
When handling the Monitor, be very careful. (Applies only
to
the product w/
monitor).
Some ofthe monitor (TV) parts are subject to high tension voltage. Even after turning off
power, some portions are still subject to high tension voltage sometimes. Monitor repair and
replacement should be performed only by those technical personnel who have knowledge
of
electricity and technical expertise.
OWhen transporting or reselling this product, be sure to attach this manual to
the product.
In the case where commercially available monitors and printers are used in this product,
only the contents relating to this product are explained herein. Some commercially
available equipment has functions and reactions not stated in this manual. Read this
manual together with the specific Instruction Manual of such equipment.
¢ Descriptions herein contained may be subject to improvement changes without notice.
¢ The contents described herein are fully prepared with due care. However, should any
question arise or errors be found, please contact SEGA.
INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.
Normally, at the time of shipment, SEGA products are in a status allowing for usage
immediately after transporting to the location. Nevertheless, an irregular situation may
occur during transportation. Before turning on power, check the following points to
ensure
that the product has been transported in asatisfactory status.
Are there any dented portions
or
defects (cuts, etc.)
on
the external surfaces ofthe
cabinet?
Are Casters and Adjusters, damaged?
Do iepower supply voltage and frequency requirements mee with those of the loca-
tion?
Are all wiring connectors correctly and securely connected? Unless connected in the
correct
direction,
connector
connections
can
not be made accurately. Do
not
insert
connectors forcibly.
Do power cords havecuts and dents?
Do the fuses used
meet
specified rating? Is the Circuit Protector in
an
energized status?
Are all accessories available?
Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be
firmly closed?
ee
Se
a
GES
gy

TABLE
OF CONTENTS
PAGE
1. HANDLING PRECAUTIONS 1
2. NAOMI SPECIFICATIONS 2
OOVQOQOGHOHO
CABINET
CASE AND FILTER BOARD
MONITOR DIRECTION AND HORIZONTAL SCANNING FREQUENCY
ERROR MESSAGE
REMOVING AND REINSTALLING THE ROM BD
ROM REPLACEMENT (ROM BD)
ROM REPLACEMENT (MAIN BD)
BATTERY REPLACEMENT (MAIN BD)
REPAIR/SERVICING AND CARTON BOX
3. SYSTEM TEST MODE 12
SSO@QAOQOHOHO
RAM TEST
JVS TEST
SOUND TEST
C.R.T. TEST
SYSTEM ASSIGNMENTS
COIN ASSIGNMENTS
BOOKKEEPING
BACKUP DATA CLEAR
CLOCK SETTING
ROM BOARD TEST
GAME TEST MODE

1. HANDLING PRECAUTIONS
A
WARNING!
IMPORTANT!
@To prevent electric shock
or
IC Board malfunctioning, be
sure
to
turn
off the power
for the cabinet when installing or removing the IC Board.
@Extraneous matter such as dust on the IC Board can cause the IC Board to generate
heat and result in afire due to short circuit, etc. Ensure the IC Board surfaces are always
kept clean.
@Be sure to connect the IC Board and connectors completely. Insufficient
insertion can damage IC Board, etc.
@For the IC Board circuit inspection, only the
use
of Logic Tester is permitted.
The
use
of ordinary testers is not permitted as these
can
damage the IC Board.
@Do not subject the IC Board to static electricity when installing the IC Board in
the cabinet or when connecting wire harness connectors to the IC Board.
@When soldering buttons, etc.
to
the wire harnesses, be
sure
to
remove
the wire
harnesses from the IC Board so as not to subject the IC Board to heat.
@Using NAOMI without the Shield Case can cause electric wave trouble. Be
sure to use NAOMI together with the accessory Shield Case.
@The monitor frequency corresponding to NAOMI is 15kHz
or
31kHz.
NAOMI can not be used for the cabinet incorporating amonitor or projector not
corresponding to 15kHz or 31kHz.
@Use NAOMI for the cabinets compatible with JVS. | Using NAOMI for the
cabinets other than those compatible with JVS can cause generation of heat anda fire.
@Concerning the display of JAMMA VIDEO STANDARD:
JAMMA VIDEO STANDARD adopted by NAOMI is referred to as JVS. As
against this Standard, the conventional JAMMA STANDARD which employs 56P Edge
Connectors adopted by ST-V, etc. is displayed as Old JAMMA STANDARD.
The specific Manual attached
to
each game sometimes displays JVS
as
JV
STANDARD, New JAMMA STANDARD,
or
JAMMA 2STANDARD against Old
JAMMA STANDARD as JAMMA STANDARD, JS, etc.
@The contents herein described
are
subject
to
change without notice.

2. NAOMI SPECIFICATIONS
@CABINET
*
Use NAOMI for the cabinet compatible with JVS.
* To use NAOMI for acabinet of Old JAMMA STANDARD, it is necessary to
prepare such parts as Power Supply, I/O BD, Audio Amplifier, etc. for conversion to
JVS.
* For inquiry as regards whether the cabinet used is compatible with JVS or
convertible for JVS, contact the Maker or Distributor of the specific cabinet.
* Even if JVS compatible, the game may not be usable if it requires aspecial
Control Panel.

2CASE AND FILTER BOARD
NAOMI Main BD is contained
in
the Shield Case.
Use NAOMI in the status with the Main BD
as
is contained in the Shield Case.
*
When using NAOMI,
ensure
that the Ventilation Ports and Heat Exhaust Fan
opening are not obstructed.
FIG. 2-2a EXTERIOR VIEW, NAOMI CASE
@NAOMI SHIELD CASE @VENTILATION PORT
@) ROM BOARD CASE ©LEG BRACKET
@FILTER BOARD ©HEAT EXHAUST FAN OPENING
PSW2 PSW1 DIPSW CNB | SGSA CN12
ON) AN
oe
Ong TOTX195| TORX194
4
=
=
ONT ON6 Go000
© ©, © @8 4 God Goo
FIG. 2-25 FILTER BOARD (839-1069 FLT BD NAOMI)
CN1: POWER SUPPLY (JST
VL
8P) 1:(N.C.) 2:43.3V 3:45V 4:412V 5
~
8:GND
CN2: POWER SUPPLY (JST VL 6P) 1:(N.C.) 2:4+3.3V 3:45V 4~ 6:GND
CN3: VIDEO OUTPUT (MINI D-SUB 15P)
CN4: STEREO-AUDIO OUTPUT (RCA PIN JACK FEMALE) RED: RIGHT WHITE: LEFT
CNS5: STANDARD I/O (SERIES
A
TYPE) Connected
to
I/O BD via. USB Cable.
CN6 ~ 9,12 :Normally not used.
TORX194, TOTX195: OPTIC FIBER CONNECTOR
Used for communication in-between plural NAOMI.
For application, refer
to
the Instruction Manual of the game for communication play.
PSW1: Functions as TEST Button.
PSW2?: Functions as SERVICE Button.
DIPSW: Used for image Frequency change, etc. Refer to @) MONITOR DIRECTION
AND HORIZONTAL SCANNING FREQUENCY.
—3-

@MONITOR DIRECTION AND HORIZONTAL SCANNING FREQUENCY
* MONITOR DIRECTION
Install the monitor in the positional direction (horizontal
or
vertical as applicable) suitable for each game.
For the monitor direction, refer
to
the attached manual of the specific game.
If
the attached Instruction
Manual does
not
refer to the monitor direction, position the monitor in the horizontal direction.
(HORIZONTAL)
Ne eee
*
HORIZONTAL SCANNING FREQUENCY :15.85kHz /31.69kHz
Which
one
of
15kHz
or
31kHz frequency,
or
both of the frequencies does the game correspond
to depends
on
each game. To find
out
the frequency the specific game corresponds to,
refer to the Instruction Manual attached to the game.
The frequency output
can
be designated by No. 1SW of DIP SW
on
the Filter BD.
ON ee 1OFF
Z
noe
DIPSW 1ON
15kHz
i
-
*
é 3 a For both of 15K and 31K, set DIP SW 2 ~ 3 to OFF
unless otherwise specified.
FIG. 2-32 FILTER BOARD DIP SW
The actual DIP SW may differ from the above Figure.
Zl
Note that due to acertain flickering and blurring, the Interlace display may be slightly inferior as
compared to Non-interlace display.
Also, if the cabinet monitor is not corresponding to Interlace display, on-screen noise may
appear and display is
not
satisfactory.
Among the games corresponding to both 15k and 31k, there
are
some
games for which the
use
of 31k
is strongly recommended.
If
such
a
game is displayed in 15k, WARNING may be displayed at the time
power is turned
on.
:
At
the time
of
the shipment
of
NAOMI Main BD, which
one
of
15k
or
31k the DIP SW is
set
to
depends
on
the games contained in the
same
package. Before installing in the
cabinet, be
sure
to check the setting contents
of
DIP SW, and change the DIP SW setting
if
necessary.
—4—

@ERROR MESSAGE
In the following cases, ERROR MESSAGE is displayed at the time power is
turned
on
and the test mode is finished, and the game is
not
playable.
ERROR 01
(DISPLAY)
ERROR 01
THIS GAME IS NOT ACCEPTABLE
BY MAIN BOARD.
(CAUSE) The ROM BOARD is not connected correctly to the MAIN BD.
(COUNTERMEASURES) First,
turn
power off,
connect
the ROM BD correctly.
If
the status is
not
improved yet, the board may be malfunctioning.
ERROR 02
(DISPLAY)
ERROR 02
THIS GAME IS NOT ACCEPTABLE
BY MAIN BOARD.
(CAUSE) A game of a certain country's version which is not compatible
with the Main BD is connected to the Main BD.
(COUNTERMEASURES) Connect
a
game of
a
country's version which is
compatible with the Main BD. Country setting change
can
not be performed in the TEST
mode.
ERROR 03
(DISPLAY)
ERROR 03
BOARD MALFUNCTIONING.
(CAUSE) BOOT ROM program cannot read the Main Board's serial ID.
(COUNTERMEASURES) Board malfunctioning.
Ask for the repair/servicing of ROM BD and MAIN BD.
ERROR 04
(DISPLAY)
ERROR 04
BOARD MALFUNCTIONING.
(CAUSE) BOOT ROM program cannot read the Main Board's serial ID.
(COUNTERMEASURES) Board malfunctioning.
Ask for the repair/servicing of ROM BD and MAIN BD.

CAUTION 51
(DISPLAY)
CAUTION 51
GAME ASSIGNMENTS ARE
INCORRECT.
SET CORRECTLY IN SYSTEM
ASSIGNMENTS OF TEST MODE.
(CAUSE) CABINET TYPE setting is not correct for the game.
(COUNTERMEASURES) Enter the TEST mode and change the CABINET TYPE
setting
of
SYSTEM ASSIGNMENTS to the setting suitable for the game.
For the
correct
setting, refer
to
the Instruction Manual attached to the game.
Certain games require the replacement of Control Panel.
CAUTION 52
(DISPLAY)
CAUTION 52
CHANGE VIDEO OUTPUT OF
THIS GAME TO THE SETTING
CORRESPONDING TO HORIZONTAL
SCANNING FREQUENCY 15KHz.
(CAUSE) 31kHz is employed when the game is corresponding to Horizontal
Scanning Frequency of 15kHz only.
(COUNTERMEASURES) Set the monitor to 15kHz, and set No. 1of NAOMI
FILTER BD DIP SW to ON.
For the setting method of monitor's Frequency, refer to the Instruction Manual of the cabinet.
If
the monitor is
not
corresponding to 15kHz, the game is
not
playable.
CAUTION 53
(DISPLAY)
CAUTION 53
CHANGE VIDEO OUTPUT OF
THIS GAME TO THE SETTING
CORRESPONDING TO HORIZONTAL
SCANNING FREQUENCY 31KHz.
(CAUSE) 15kHz is employed when the game is corresponding to Horizontal
Scanning Frequency of 31kHz only.
(COUNTERMEASURES) Set the monitor to 31kHz, and set No. 1 of NAOMI
FILTER BD DIP SW to OFF.
For the setting method of monitor's Frequency, refer to the Instruction Manual of the cabinet.
If the monitor is not corresponding to 31kHz, the game is not playable.
CAUTION 54
(DISPLAY)
CAUTION 54
GAME ASSIGNMENTS ARE
INCORRECT.
SET CORRECTLY IN SYSTEM
ASSIGNMENTS OF TEST MODE.
(CAUSE) The setting of MONITOR TYPE differs from the correct setting of the game.
(COUNTERMEASURES) Enter the TEST mode, and change the MONITOR TYPE
setting
of
MONITOR TYPE in SYSTEM ASSIGNMENTS to the
correct
setting suitable
for the game. For the
correct
setting, refer to the Instruction Manual attached to the game.
If necessary, perform Horizontal/Vertical transposition of the monitor, as applicable.

©) REMOVING AND REINSTALLING THE ROM BOARD
Ensure that the power is off before performing work.
*
REMOVING
1) Disconnect all of the wirings connected to NAOMI , and remove NAOMI
from inside the cabinet.
2) Remove the 4
screws
(M3
x
30) which
secure
the ROM BD Case
on
NAOMI Case.
3) Remove ROM BD Case upward by holding both sides.
*
INSTALLING
1) Make
sure
that the
connector
direction is correct, and insert the ROM BD Case fully
onto NAOMI Main BD.
2) By using the 4
screws
(M3
x
30) previously removed
as
per REMOVING 2) above,
secure ROM BD Case to NAOMI Case.
SCREW(4)
ROM BOARD
WHEN INSTALLING, BE CAREFUL
f
RSS
OF THIS DIRECTION!
ING
&

©ROM REPLACEMENT (ROM BD)
Do not perform this work unless otherwise particularly instructed due to game
version change, etc.
1) Turn power off, and
remove
ROM BD Case from NAOMI Case by
referring
to
©) REMOVING
AND
REINSTALLING THE ROM BOARD above.
2) Remove the 2tap
screws
(M3
x
10) from the back
of
ROM BD Case
to
remove
the ROM
BD Case from ROM BD.
3) Remove ROM BD surface side on-socket ROM (IC22) from the socket
by using an IC EXTRACTOR.
To prevent tearing
off
on-board patterns, etc., do
not
use
tools such asa
flat-
blade type screwdriver, etc. other than the IC EXTRACTOR. For malfunctioning
resulting from using tools other than the IC EXTRACTOR, repair shall be performed on a
pay-basis. Be careful of this point.
4) Insert the
new
ROMs into the socket by paying attention to the inserting direction.
In accordance with the instructions of the supplier of new ROMs, take proper
action
to
dispose of the removed old ROMs by sending back, discarding after cutting
off
pins,
or
appropriately storing, as applicable. When instructed
to
change JUMPER
SW(JP1), change the Jumper SW in accordance with the instructions.
5) Reinstall ROM BD Case
to
ROM BD by paying attention
to
the correct
direction of ROM BD and secure with the 2tap screws (3x10) removed as per 2) above.
6) By referring to ©) REMOVING AND REINSTALLING THE ROM
BOARD, reinstall ROM BD Case to NAOMI Case.
TAPPING SCREW (2)
ROM BOARD

@ROM REPLACEMENT (MAIN BD)
Do not perform this work unless otherwise particularly instructed due
to
BOOT
ROM version change, etc.
1) Turn power off, and remove ROM BD Case from NAOMI Case by
referring to 6) REMOVING AND REINSTALLING THE ROM BOARD above.
2) Remove on-socket ROM (IC27) of NAOMI Main BD from the socket
by using an IC EXTRACTOR.
To prevent tearing
off
on-board patterns, etc., do
not
use
tools
such as a flat-blade type screwdriver, etc. other than the IC EXTRACTOR. For
malfunctioning resulting from using tools other than the IC EXTRACTOR, repair shall be
performed
on
a
pay-basis. Be careful of this point.
3) Insert the
new
ROMs into the socket by paying attention to the inserting
direction. In accordance with the instructions of the supplier of
new
ROMs, take proper
action to dispose of the removed old ROMs by sending back, discarding after cutting off
pins, or appropriately storing, as applicable.
4) By referring
to
6) REMOVING AND REINSTALLING THE ROM BOARD, reinstall ROM
BD Case
to
NAOMI Case.
ROM
DO NOT USE AFLAT-BLADE SCREWDRIVER.

BATTERY REPLACEMENT (MAIN BD)
Except for special
cases
such
as
using up the battery, etc., do
not
perform this work.
1) Turn power off, and
remove
ROM BD Case from NAOMI Case by referring
to
©) REMOVING AND REINSTALLING THE ROM BOARD above.
2) Carefully remove the battery on the Battery Holder of NAOMI Main BD.
3) With the positive pole facing upward, insert the
new
Battery (CR2032) into the Holder.
4) By referring
to
©) REMOVING AND REINSTALLING THE ROM BOARD,
reinstall ROM BD Case to NAOMI Case.
BATTERY FOR NAOMI
SEGA PART No. 401-0054
SEGA PART NAME BATTERY CR2032/1F MATSUSHITA
BATTERY CR2032
FIG. 4

@REPAIR/SERVICING AND CARTON BOX
When transporting NAOMI for repair/servicing, follow the instructions below.
The accessory
carton
box is needed when transporting NAOMI for repair/servicing. Be
sure
to safely store the Carton Box.
* When sending for repair/servicing, remove all of the wire harnesses and cables
from the Filter BD in front.
* When transporting NAOMI Main BD for the repair/servicing, ensure that the ROM
BD used is in
an
as
is installed status.
* When sending the NAOMI Main BD for repair/servicing, be sure to put it in the
accessory carton box together with the Shield Case. The Main Board (Shield Case) and
carton box have an identical serial number. When sending, ensure that the combination
serial number is identical with each other.
* When putting NAOMI SHIELD CASE in the carton box, the Leg Bracket need
not be removed.
* Where the repair /servicing is to be performed depends on the maker of each
game on the ROM BD. Check this by referring to the attached Instruction Manual.
"CHECK SIDE” DISPLAY
SERIAL NO.

3. SYSTEM TEST MODE
This test mode mainly allows the IC Board to be checked for accurate functioning,
monitor color
to
be adjusted
as
well as COIN ASSIGNMENTS AND GAME
ASSIGNMENTS
to
be adjusted.
TEST ITEM SELECT
1) After turning power on, press the TEST button
to
have the following test item
menu
displayed.
SYSTEM MENU
USA VERSION
RAM TEST
JVS TEST
SOUND TEST
C.R.T. TEST
SYSTEM ASSIGNMENTS
COIN ASSIGNMENTS
BOOKKEEPING
BACKUP DATA CLEAR
CLOCK SETTING
ROM BOARD TEST
GAME TEST MODE
[ZOMBIE ZONE ] <- Game name is
entered.
->
EXIT
SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON
2) Press the SERVICE button to move the arrow. Bring the arrow to the desired
item and press the TEST button.
3) Upon finishing the test, bring the
arrow
to
EXIT and press the TEST button to
return to the Game mode.
IMPORTANT!
The contents of setting changes in SYSTEM ASSIGNMENTS, COIN ASSIGNMENTS,
and GAME TEST MODE are stored when the test mode is EXITed. If the power is
turned off before EXITing, the contents of setting changes
are
ineffective.
Be very careful of this point.

@) RAM TEST
This allows for checking the functioning of the RAM
on
the NAOMI Main BD.
"GOOD" is displayed for satisfactory RAMs, and "BAD" is indicated for irregular RAMs, if any.
RAM TEST
1¢29 GOOD
1¢35 GOOD
1¢16 GOOD 1C18 GOOD
1¢20 GOOD 1C22 GOOD
1c09 GOOD 1C10 GOOD
1¢11 GOOD 1012 GOOD
PRESS TEST BUTTON TO EXIT
During test, "TESTING NOW" is displayed.
Press the TEST button to return to the menu mode.

@IVS TEST
In this test, Specifications
of
the I/O Board connected
to
NAOMI
can
be checked,
and INPUT TEST
can
be performed. First, I/O Board Specifications
are
displayed.
JVS TEST
INPUT TEST
NEXT NODE
—> EXIT
NODE 1/1
NAME SEGA ENTERPRISES, LTD.
1/0 838-18683
VER 1.04
98/12
CMD VER 1.1
JVS VER 2.0
COM VER 1.0
SWITCH 2PLAYER(S) 11BITS
COIN 2SLOT
ANALOG 8CH
ROTARY OCH
KEYCODE 0
SCREEN X:0 Y:0 CH:0
CARD OSLOT
HOPPER OUT OCH
DRIVER OUT 8SLOT
ANALOG OUT OCH
CHARACTER CHARA:0 LINE:0
BACKUP 0
SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON
(A)
(B)
(C)
|Name and version of I/O BOARD.
Select with the SERVICE button and press the TEST button.
(A) INPUT TEST: Proceeds
to
the INPUT TEST of I/O BOARD being displayed.
(B) NEXT NODE: In the
case
where
more
than 2I/O Boards
are
connected,
proceeds
to
the
next
I/O Board.
(C) EXIT: Returns to
INPUT TEST SCREEN
the
menu
mode.
NODE 1/1
SWITCH
SYSTEM
PLAYER1
PLAYER2
COIN
JVS TEST
INPUT TEST
NEXT NODE
—> EXIT
00000000
00000000
00000000
00000000
00000000
1from 0.
ANALOG
0000 0000
0000 0000 0000 0000
0000 0000 0000 0000
SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON
0000 and FFOO.
p> When INPUT is performed for the switches
ofControl Panel, etc., the value changes
to
Be If the Coin SW is inputted, the count starts.
When the TEST MODE is finished, the
count is cleared and returned to[ 0000].
p> Analogue values
are
displayed between