Server Express SE-3 User manual

Server Express®
MODELS:
SE-3
SE-3DI
SE-4
SE-5
SE-5DI
Used with pouches up to
1½ gallons with 16mm tments.
for purchasing our Server Express®Pouched Condiment
Dispenser. This portion controlled unit is sealed and
sanitary, achieves excellent evacuation and has only a few
parts for easy clean-up.
SIMPLIFY CONDIMENT MANAGEMENT— GO POUCHED
Thank You

Page 2
OLDER MODELS
(LIDS WITH SQUARE CORNERS)
07180 07185 07186
07124, 07127 07079 07083
07122, 07123 07104 07105
PARTS
LEVER
07014
LID LID ASSEMBLY
ROLLER
07056
PUMP
07398
SHROUD
POUCH SUPPORT
07159
FEET
92098
See page 3.
HINGE PIN
07161
MODEL(S) LID LID
(ROUNDED ASSEMBLY
CORNERS)
07180 07843 07867
07124, 07127 07865 07866
07122, 07123 07851 07868
MODEL REPLACEMENT
SHROUD
07123 07857
07127 07864
07122 07856
07124 07863
11" BRUSH
82049
07180 07848
SERVER EXPRESS®MODELS
SE-3
07124
Triple
SE-4
07180
Quadruple
SE-5
07122
Quintuple
SE-3DI
07127
Triple Drop-In
SE-5DI
07123
Quintuple
Drop-In

Page 3
SAFETY
IMPORTANT
Clean, rinse, sanitize, and dry parts daily or regularly to
comply with local sanitization requirements.
According to food and safety regulations, most
foods must be stored and/or served at certain
temperatures or they could become hazardous.
Check with local food and safety regulators for
specic guidelines. Server Products, Inc. cannot be
responsible for the serving of potentially hazardous
product.
Drop-in units can be used either on a countertop
surface or can be dropped into an opening in
a countertop.
NSF International lists this pump as:
“Not acceptable for dispensing potentially
hazardous foods.”
DROP-IN UNITS
PUMP MODEL 07398
MODEL RECOMMENDED
NUMBER COUNTERTOP
OPENING SIZE
07123 QUINTUPLE 8 1/2" x 27 3/16"
07127 TRIPLE 8 1/2" x 16 3/8"
DOME 07383
PINCH VALVE 07798
PUMP HOUSING 07388
TUBE
07089
CONNECTOR*
07381
DISCHARGE
FITTING*
07796
*Unit includes 2 each spare parts.

Page 4
PUMP ASSEMBLY WASH ALL PARTS
PROPERLY BEFORE USE. See page 7.
Lubricate with a small amount of clean water.
Rotate and position until both pegs on
housing t into holes on tube.
INSTALL TUBE
3
into pump housing discharge tube.
Place loop of tting around peg on end of
discharge tube to secure.
INSERT DISCHARGE FITTING
5
Lubricate with a small amount of clean water.
Rotate and position until both pegs on
connector t into holes on tube.
Connector must point away from end of
discharge tube.
INSERT CONNECTOR
4
INSERT PINCH VALVE
1
into pump housing.
Wrap loop
around lower
opening to
secure dome.
INSTALL DOME
2
Press dome into
housing fully.
Ensure valve ap
covers bottom
opening.
TIP: Squeeze the pinch valve
open before installation to
ensure it isn’t stuck shut.

Page 5
WASH ALL PARTS
PROPERLY BEFORE USE. See page 7. SETUP
ATTACH POUCHES TO PUMPS
1
Firmly press piercing connector into
center of pouch tment.
An audible click indicates
a secure connection.
CLICK
Slide pouch and pump into
pouch support within shroud.
Align pump guides into slots in shroud.
INSTALL PUMPS
2
PLACE LID ON TOP
3
Press lever several times until you see
product in discharge tube.
PRIME PUMPS
4

Page 6
TAKE-DOWN & DISASSEMBLY
REMOVE PUMP & POUCH
2
DETACH PUMP FROM POUCH
3
REMOVE LID
1
FLUSH & RINSE PUMP
4
Place lower end of pump into container of
hot water. Pump until all remaining product is
expelled and only water ows from discharge
tube.
DISASSEMBLE
5
If lid reassembly is needed,
or to specify a different portion size:
PORTION CONTROL
THE LID IS SET TO DELIVER 1 OZ PORTIONS.
One hinge pin attaches lever to lid.
Second hinge pin attaches roller to lever.
(Controls portion dispensed.)
1/4 OZ
3/4 OZ
1/2 OZ
1 OZ
Install hinge pin through center
roller hole and desired portion
hole on lever.
Pin snaps into place.

Page 7
• External surfaces may be wiped clean with
a clean damp cloth.
• Glass and surface cleaners approved for
use in food contact areas may be used.
• Do not use abrasive, caustic or ammonia
based cleansers.
• Do not use metal scrapers or cleaning
pads that could scratch surfaces.
CLEANING
CLEAN
After disassembling,
clean all washable parts
with soap and hot water.
RINSE
fully with clear water.
1
SANITIZE
all parts according to local sanitization
requirements. All parts in contact with
food must be sanitized.
AIR DRY
all parts fully.
2
3
4
Use dishwashing
soap and hot water
Pump cleaning
YES!
• Use nylon brush to clean any
conned areas.
• Pump components are dishwasher safe.
• Refer to instruction manual provided
with pump.
This unit is constructed with
stainless steel— one of the best
materials for food serving and
storage.
If you notice corrosion beginning on
any stainless steel surface, you may need to
change the cleansing agent, sanitizing agent, or
the cleaning procedures you are using.
CARE OF STAINLESS STEEL
• A mildly abrasive nylon or brass brush may
be used to remove any stubborn food or
mineral deposits on interior surfaces of unit.
• Fully rinsing and drying all parts can help
prevent corrosion. Elements and minerals in
tap water can accumulate on stainless steel
parts and create corrosion.
• Do not use products containing acids,
alkalines, chlorine, or salt. These agents can
corrode stainless steel.

Page 8 Manual #EM_01552_RevM 012122
GENERAL SERVICE,
REPAIR OR RETURNS
Before sending any item to Server Products for
service, repair, or return, contact Server Products
customer service to request a Return Authorization
Number. Merchandise must be sent to Server
Products with this number. Service is extremely
prompt. Typically, units are repaired and ship out
within 48 hours of receipt.
Merchandise being returned for credit must be in
new and unused condition and not more than 90
days old and will be subject to a 20% restocking
charge.
TIP: Squeeze the pinch valve
open before installation to
ensure it isn’t stuck shut.
TROUBLESHOOTING
• Ensure pinch valve is inserted in housing.
• Ensure connector is snapped fully in place to
tment in pouch.
• Ensure pump is properly attached to pouch.
• Clean pump thoroughly.
• Ensure pump is properly installed into retaining
slots inside front wall of shroud.
PRODUCT DOESN’T PUMP?
• Wet parts with clean water to help t.
DIFFICULT TO ATTACH PARTS?
• Clean thoroughly. Food residue could prevent
a tight seal between dome and housing.
• Ensure dome edges are ush with housing.
DOME POPS OFF?
SERVER PRODUCTS
LIMITED WARRANTY
This Server product is backed by a two-year
limited warranty against defects in materials and
workmanship. See Server-Products.com for details.
NEED HELP?
Please be prepared with your Model, P/N and
Series located on the lid or base of the unit.
Example:
Chat with us!
[email protected]
262.628.5600 | 800.558.8722
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA MODEL
XXXX
P/N
#####
SERIES
##X ##X