Server InSeason INS User manual

InSeason™
Seasoning
Dispenser
...for purchasing our InSeason Dispenser™—
This handheld, lightweight model dispenses
precise portions of granular seasonings for
consistent taste and texture.
PERFECTLY SEASONED EVERY TIME!
Thank You
MODEL: INS

Page 2
ASSEMBLY WASH ALL PARTS
PROPERLY BEFORE USE. See page 5.
SELECT PORTION TRIGGER
1
INSERT TRIGGER
2
With unit upside down on countertop, slide
spring end of trigger assembly into side slot.
Smooth side of trigger should face down.
Portion size is also
stamped in trigger cavity.
(if more than one is provided).
Trigger determines portion size dispensed.
1/2 TSP
1/3 TSP
1/4 TSP
0.15 TSP
1/8 TSP
1/16 TSP
PORTION SIZE TRIGGER
GREEN
BLUE
BLACK
WHITE
BURGUNDY
TAN
INSTALL CLOSER PLATE
3
into unit body.
Hold closer plate by grasp tab.
Slowly push trigger assembly into unit body.
Ensure spring does not pop loose.
Insert closer plate rim tab into largest
interior opening of trigger.

Page 3
Portion size is also
stamped in trigger cavity.
FILL UNIT
5
Flip unit right-side up and
add granular ingredient.
INSTALL LID
6
onto unit body, rotating clockwise to tighten.
INSTALL SPREADER
4
onto unit body, rotating clockwise to tighten.
IMPORTANT: Refill
when product level
falls below fill line.

Page 4
SAFETY
According to food and safety regulations, most
foods must be stored and/or served at certain
temperatures or they could become hazardous.
Check with local food and safety regulators for
specific guidelines. Server Products, Inc. cannot be
responsible for the serving of potentially hazardous
product.
The dispenser is designed for use in high-heat
environments, but is not intended for direct contact
with heat sources such as griddle surfaces.
IMPORTANT
Clean, rinse, sanitize, and dry parts daily or regularly
to comply with local sanitization requirements.
NSF International listed.
DISASSEMBLY
EMPTY UNIT
Pour out any remaining ingredient.
2
REMOVE LID
1REMOVE SPRING FROM TRIGGER
only if necessary for cleaning.
• Pry off spring with a flathead screwdriver.
• Push straight end of spring out of center groove
in circular tab of trigger.
RE-INSTALL SPRING
• Align straight end of spring into center groove in
circular tab of trigger.
• Use flathead screwdriver to press down on
straight end of spring.
• Snap spring into circular tab of trigger.
REMOVE SPREADER
3
REMOVE CLOSER PLATE
Set unit upside down on countertop.
Grasp tab of closer plate while holding
trigger in.
Pull closer plate up and out of unit.
Slowly release trigger to home position,
to ensure spring does not pop loose.
4
REMOVE TRIGGER ASSEMBLY
from side slot of unit.
5

Page 5
CLEANING
SANITIZE
all parts according to local sanitization
requirements. All parts in contact with food
must be sanitized.
3
AIR DRY
all parts fully before refilling.
5
Use dishwashing
soap and hot water
YES!
• Dishwasher safe
• Do not use abrasive, caustic or ammonia
based cleansers.
• Do not use cleansing agents with high
concentrations of acid, alkaline or chlorine.
• Do not use metal scrapers or cleaning
pads that could scratch surfaces.
RINSE
Fully rinse all parts thoroughly with clear
water.
2
WASH
After disassembly, wash all parts with
dishwashing detergent and hot water.
1
Heat and moisture can cause ingredients
to settle and become packed in.
• Shake unit to dislodge light clumping.
• Ensure ingredients have not become clogged
within the unit—disassemble and inspect.
• Clean unit and air dry fully before refilling.
• Ensure ingredient level is above fill line.
INCONSISTENT PORTIONS?
• Ensure closer plate is properly installed with
rim tab in the largest opening of trigger.
TRIGGER WON’T PUSH IN?
NO YES
TROUBLESHOOTING

Page 6
DID YOU KNOW?
THERE ARE TWO KINDS OF SPREADERS
SPREAD PATTERN
Wide Disbursement
DROP PATTERN
4"Diameter
(patty or single serving) (fry dump or platter)
Dispenser includes one of the following spreader styles.
Spreaders determine dispensing pattern.
TIP: This spreader has
small holes in the center.
GENERAL SERVICE,
REPAIR OR RETURNS
Before sending any item to Server Products for service,
repair, or return, contact Server Products customer
service to request a Return Authorization Number.
Merchandise must be sent to Server Products with this
number. Service is extremely prompt. Typically, units
are repaired and ship out within 48 hours of receipt.
Merchandise being returned for credit must be in new
and unused condition and not more than 90 days old
and will be subject to a 20% restocking charge.
SERVER PRODUCTS
LIMITED WARRANTY
Server Products equipment is backed by a
two-year limited warranty against defects in
materials and workmanship.
For complete warranty information go to:
www.Server-Products.com

Page 7
RELATED ITEMS
EXPRESS™ CONDIMENT SYSTEMS
• Dispense from 1½ gallon pouches
with a 16mm fitment, forming a sealed,
sanitary system.
• Durable, plastic pumps have only a few
parts, are quick to breakdown and achieve
up to 98% evacuation.
• Models available for countertop and drop-in
applications to dispense 1–6 condiments.
FASTFILL™ BOTTLE FILLER (FSF 87690)
• Refills squeeze bottles in seconds.
• Allows you to use the same ketchup
SKU for both front and back-of-house;
uses common 1½ gallon pouches with
16mm fitment.
• Wall-mounted, lever-operated dispenser
applies pressure to the bag for fast and
complete evacuation.

Page 8 Manual #01674-RevF 081816
HELP or ORDERING REPLACEMENT PARTS
262.628.5600 | 800.558.8722
[email protected]
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA
LID
87091
BODY
87092
CLOSER PLATE
87095
AVAILABLE
TRIGGER ASSEMBLIES
Please be prepared with the Part Numbers for your
items. Individual part numbers are listed above.
1/2 TSP
1/3 TSP
1/4 TSP
0.15 TSP
1/8 TSP
1/16 TSP
PORTION SIZE TRIGGER PART
GREEN
BLUE
BLACK
WHITE
BURGUNDY
TAN
87126
87127
87128
87129
87131
87132
INSEASON™INDIVIDUAL PARTS
AVAILABLE
SPREADERS:
DROP PATTERN
4" DIAMETER
87102
SPREAD PATTERN
WIDE DISBURSEMENT
87096