SEW-Eurodrive MOVIFIT FC User manual

*21316996_1214*
Drive Technology \ Drive Automation \ System Integration \ Services
Operating Instructions
Decentralized Drive Control
MOVIFIT®FC
Edition 12/2014 21316996/EN

SEW-EURODRIVE—Driving the world

Contents
Operating Instructions – MOVIFIT® FC 3
Contents
1General information .................................................................................................................. 6
1.1 How to use this documentation ...................................................................................... 6
1.2 Structure of the warning instructions .............................................................................. 6
1.3 Rights to claim under limited warranty ........................................................................... 8
1.4 Exclusion of liability ........................................................................................................ 8
1.5 Other applicable documentation .................................................................................... 8
1.6 Product names and trademarks ..................................................................................... 8
1.7 Copyright notice ............................................................................................................. 8
2Safety notes ............................................................................................................................... 9
2.1 Preliminary information .................................................................................................. 9
2.2 General information ........................................................................................................ 9
2.3 Target group ................................................................................................................... 9
2.4 Designated use ............................................................................................................ 10
2.5 Transportation, storage ................................................................................................ 10
2.6 Installation .................................................................................................................... 11
2.7 Electrical connection .................................................................................................... 11
2.8 Safe disconnection ....................................................................................................... 11
2.9 Operation ..................................................................................................................... 12
3Unit structure........................................................................................................................... 13
3.1 MOVIFIT® FC ............................................................................................................... 13
3.2 Overview – Connection configuration .......................................................................... 14
3.3 EBOX (active electronics unit) ..................................................................................... 16
3.4 ABOX (passive connection unit) .................................................................................. 17
3.5 Hygienicplus design (optional) ........................................................................................ 18
3.6 MOVIFIT® with L10 PROFINET interface SCRJ/POF .................................................. 20
3.7 MOVIFIT® FC type designation .................................................................................... 21
4Mechanical installation ........................................................................................................... 28
4.1 General information ...................................................................................................... 28
4.2 Tools required .............................................................................................................. 28
4.3 Permitted mounting position ......................................................................................... 29
4.4 Installation .................................................................................................................... 30
4.5 Central opening/closing mechanism ............................................................................ 36
4.6 Tightening torques ....................................................................................................... 39
4.7 MOVIFIT® Hygienicplus design ....................................................................................... 41
5Electrical installation............................................................................................................... 44
5.1 General information ...................................................................................................... 44
5.2 Installation planning taking EMC aspects into account ................................................ 44
5.3 Installation instructions (all versions) ........................................................................... 46
5.4 Additional installation instructions for group drives ...................................................... 57
5.5 Installation topology (example) .................................................................................... 58
5.6 Standard ABOX MTA...-S02.-...-00 .............................................................................. 59
5.7 Hybrid ABOX MTA...-S42.-...-00 .................................................................................. 79
5.8 Hybrid ABOX MTA...-S52.-...-00 .................................................................................. 82
21316996/EN – 12/2014

Contents
Operating Instructions – MOVIFIT® FC
4
5.9 Hybrid ABOX MTA...-S533-...-00/L10 .......................................................................... 85
5.10 Hybrid ABOX MTA...-S62.-...-00 .................................................................................. 89
5.11 Hybrid ABOX MTA...-I55.-...-00, MTA...-G55.-...-00 ..................................................... 92
5.12 Hybrid ABOX MTA...-I65.-...-00, MTA...-G65.-...-00 ..................................................... 95
5.13 Electrical connections .................................................................................................. 98
5.14 Encoder connection ................................................................................................... 112
5.15 Power bus connection examples ............................................................................... 114
5.16 Fieldbus systems connection examples ..................................................................... 115
5.17 Hybrid cable ............................................................................................................... 119
5.18 Wiring notes ............................................................................................................... 125
5.19 Wiring check ............................................................................................................... 126
6 Startup.................................................................................................................................... 127
6.1 General information .................................................................................................... 127
6.2 Requirements ............................................................................................................. 128
6.3 Description of the DIP switches ................................................................................. 128
6.4 Startup procedure ...................................................................................................... 138
6.5 Startup of MOVIFIT® on the fieldbus .......................................................................... 139
6.6 Starting up MOVIFIT® frequency inverter ................................................................... 143
7Operation................................................................................................................................ 146
7.1 Status LEDs for MOVIFIT® FC ................................................................................... 146
7.2 Manual operation using the DBG keypad .................................................................. 168
8Service.................................................................................................................................... 169
8.1 Unit diagnostics .......................................................................................................... 169
8.2 Error list ...................................................................................................................... 169
8.3 Inspection/maintenance ............................................................................................. 172
8.4 SEW‑EURODRIVE Service ........................................................................................ 172
8.5 Shutdown ................................................................................................................... 173
8.6 Storage ....................................................................................................................... 173
8.7 Extended storage ....................................................................................................... 173
8.8 Disposal ..................................................................................................................... 174
9Technical data........................................................................................................................ 175
9.1 Conformity .................................................................................................................. 175
9.2 Design with operating point 400 V/50 Hz ................................................................... 176
9.3 Design with operating point 460 V/60 Hz ................................................................... 178
9.4 Electronics data .......................................................................................................... 180
9.5 Binary inputs .............................................................................................................. 181
9.6 Binary outputs DO00 – DO03 .................................................................................... 181
9.7 Binary output DB00 .................................................................................................... 182
9.8 Interfaces ................................................................................................................... 182
9.9 Cable type "A" hybrid cable ........................................................................................ 187
9.10 4Q operation for motors with mechanical brake ......................................................... 189
9.11 Internal braking resistors ............................................................................................ 190
9.12 External braking resistors ........................................................................................... 191
9.13 Hygienicplus design ...................................................................................................... 192
21316996/EN – 12/2014

Contents
Operating Instructions – MOVIFIT® FC 5
9.14 Accessories ................................................................................................................ 194
9.15 Dimension drawings ................................................................................................... 195
10 Declaration of Conformity .................................................................................................... 203
11 Address list............................................................................................................................ 206
Index ....................................................................................................................................... 216
21316996/EN – 12/2014

1General information
How to use this documentation
Operating Instructions – MOVIFIT® FC
6
1General information
1.1 How to use this documentation
This documentation is an integral part of the product. The documentation is intended
for all employees who perform assembly, installation, startup, and service work on the
product.
The documentation must be provided in a legible format. Ensure that persons respon-
sible for the machinery and its operation as well as persons who work on the unit inde-
pendently have read through the documentation carefully and understood it. If you are
unclear about any of the information in this documentation or require further informa-
tion, please contact SEW-EURODRIVE.
1.2 Structure of the warning instructions
1.2.1 Meaning of signal words
The following table shows the grading and meaning of the signal words for warning in-
structions.
Signal word Meaning Consequences if disregarded
DANGER Imminent hazard Severe or fatal injuries
WARNING Possible dangerous situation Severe or fatal injuries
CAUTION Possible dangerous situation Minor injuries
NOTICE Possible damage to property Damage to the drive system or its
environment
NOTE Useful information or tip: Simplifies
handling of the drive system.
1.2.2 Structure of section-specific warning instructions
Section-specific warning instructions do not apply to a specific action, but to several
actions pertaining to the one area. The hazard symbols used either indicate a general
hazard or a specific hazard.
Section-specific warning instructions are structured as follows:
SIGNAL WORD
Type and source of hazard.
Possible consequence(s) if disregarded.
• Measure(s) to prevent hazard.
21316996/EN – 12/2014

1
General information
Structure of the warning instructions
Operating Instructions – MOVIFIT® FC 7
Meaning of the hazard symbols
The hazard symbols in the warning instructions have the following meaning:
Hazard symbol Meaning
General hazard
Warning of dangerous electrical voltage
Warning of hot surfaces
Warning of risk of crushing
Warning of suspended load
Warning of automatic restart
1.2.3 Structure of embedded warning instructions
Embedded warning instructions are included in the instructions directly just before the
description of the dangerous action.
Embedded warning instructions are structured as follows:
• SIGNAL WORD Type and source of hazard.
Possible consequence(s) if disregarded.
– Measure(s) to prevent hazard.
21316996/EN – 12/2014

1General information
Rights to claim under limited warranty
Operating Instructions – MOVIFIT® FC
8
1.3 Rights to claim under limited warranty
A requirement of fault-free operation and fulfillment of any rights to claim under limited
warranty is that you adhere to the instructions in the documentation. Read the docu-
mentation before you start working with the product.
1.4 Exclusion of liability
You must comply with the information contained in this documentation to ensure safe
operation and to achieve the specified product characteristics and performance fea-
tures. SEW-EURODRIVE assumes no liability for injury to persons or damage to
equipment or property resulting from non-observance of these operating instructions.
In such cases, any liability for defects is excluded.
1.5 Other applicable documentation
Note also the following documentation:
• "DR.71 – 315 AC Motors" operating instructions
• and fieldbus interface manual
– e.g. "MOVIFIT® Function Level "Classic" .."
– e.g. "MOVIFIT® Function Level "Technology" .."
• and functional safety manual
– e.g. "MOVIFIT® MC/FC – Functional Safety"
– e.g. "MOVIFIT® MC/FC – Functional Safety with S12 Safety Option"
(only for MOVIFIT® with S12 safety option)
You can download or order these publications on the Internet (http://
www.sew‑eurodrive.com under the heading "Documentation").
1.6 Product names and trademarks
All product names included in this documentation are trademarks or registered trade-
marks of the respective titleholders.
1.7 Copyright notice
© 2015 SEW‑EURODRIVE. All rights reserved.
Unauthorized reproduction, modification, distribution or any other use of the whole or
any part of this documentation is strictly prohibited.
21316996/EN – 12/2014

2
Safety notes
Preliminary information
Operating Instructions – MOVIFIT® FC 9
2Safety notes
The following basic safety notes must be read carefully to prevent injury to persons
and damage to property. The operator must ensure that the basic safety notes are
read and observed. Ensure that persons responsible for the system and its operation,
as well as persons who work independently on the unit, have read through the operat-
ing instructions carefully and understood them. If you are unclear about any of the in-
formation in this documentation, or if you require further information, please contact
SEW‑EURODRIVE.
2.1 Preliminary information
The following safety notes are principally concerned with the use of MOVIFIT® units. If
you use other SEW components, also refer to the safety notes for these particular
components in the corresponding documentation.
Also observe the additional safety notes provided in the individual chapters of this
document.
2.2 General information
Never install or operate damaged products. In the event of damage, submit a com-
plaint to the shipping company immediately.
During operation, the MOVIFIT® unit can have live or uninsulated parts, as well as hot
surfaces according to the degree of protection.
Removing required covers without authorization, improper use or incorrect installation
and operation may result in severe injury to persons, or damage to machinery. Refer
to the documentation for more information.
2.3 Target group
Only qualified electricians are authorized to install, start up or service the units or
correct unit faults (observing IEC 60364 or CENELEC HD 384 or DIN VDE 0100 and
IEC 60664 or DIN VDE 0110 as well as national accident prevention regulations).
Qualified electricians in the context of these basic safety notes are all persons familiar
with installation, assembly, startup and operation of the product who possess the nec-
essary qualifications.
All persons involved in any other work, such as transportation, storage, operation and
waste disposal, must be trained appropriately.
21316996/EN – 12/2014

2Safety notes
Designated use
Operating Instructions – MOVIFIT® FC
10
2.4 Designated use
MOVIFIT® is a component intended for installation in electrical systems or machines.
In case of installation in machines, startup of MOVIFIT® units (i.e. start of designated
operation) is prohibited until it is determined that the machine meets the requirements
stipulated in the Machinery Directive 2006/42/EC.
Startup (i.e. the start of designated use) is only permitted under observance of EMC
Directive 2004/108/EC.
MOVIFIT® meets the requirements stipulated in the low voltage directive 2006/95/EC.
The standards contained in the declaration of conformity are used for MOVIFIT®.
Adhere to the technical data and information on the connection requirements as provi-
ded on the nameplate and in the documentation.
2.4.1 Safety functions
MOVIFIT® may not perform any safety functions unless they are described and ex-
pressly approved.
For safety applications, ensure that the information in the following publications is ob-
served.
• For MOVIFIT® with STO (with or without S11 PROFIsafe option):
"MOVIFIT® MC/FC – Functional Safety" manual
• For MOVIFIT® with S12 safety option:
"MOVIFIT® MC/FC – Functional Safety with S12 Safety Option" manual
Use only those components in safety applications that were explicitly designed and
delivered for this purpose by SEW‑EURODRIVE. Safety-related components are
marked with the FS logo for functional safety.
2.4.2 Hoist applications
Hoist applications are only permitted with MOVIFIT® FC if a hoist startup has been
performed.
Do not use MOVIFIT® FC as a safety device in hoist applications. Use monitoring sys-
tems or mechanical protection devices as safety equipment to avoid possible damage
to property or injury to people.
2.5 Transportation, storage
Observe the notes on transportation, storage and proper handling. Observe the climat-
ic conditions as stated in the "Technical Data" sections.
21316996/EN – 12/2014

2
Safety notes
Installation
Operating Instructions – MOVIFIT® FC 11
2.6 Installation
The units must be installed and cooled according to the regulations and specifications
in the corresponding documentation.
Protect MOVIFIT® from excessive strain.
The following applications are prohibited unless explicitly permitted:
• Use in potentially explosive atmospheres.
• Use in areas exposed to harmful oils, acids, gases, vapors, dust, radiation, etc.
• Use in non-stationary applications with strong mechanical oscillation and impact
loads; see chapter "Technical Data".
2.7 Electrical connection
Observe applicable national accident prevention guidelines (e.g. BGV A3) when work-
ing on a live MOVIFIT®.
Perform electrical installation according to the pertinent regulations (e.g. cable cross
sections, fusing, protective conductor connection). For any additional information, refer
to the applicable documentation.
For notes on EMC-compliant installation, such as shielding, grounding, arrangement
of filters and routing of lines, refer to chapter "Installation instructions". The manufac-
turer of the system or machine is responsible for maintaining the limits established by
EMC legislation.
Protective measures and protection devices must comply with the regulations in force
(e.g. EN 60204-1 or EN 61800-5-1).
2.8 Safe disconnection
MOVIFIT® meets all requirements for safe disconnection of power and electronic con-
nections in accordance with EN 61800-5-1. All connected circuits must also satisfy the
requirements for safe disconnection to ensure reliable isolation.
21316996/EN – 12/2014

2Safety notes
Operation
Operating Instructions – MOVIFIT® FC
12
2.9 Operation
Systems in which MOVIFIT® is installed must, if necessary, be equipped with addition-
al monitoring and protection devices according to applicable safety regulations; e.g.,
the German law governing technical equipment (Gesetz über technische Arbeitsmit-
tel), accident prevention regulations, etc. Additional protective measures may be nec-
essary for applications with increased hazard potential. Changes to MOVIFIT® using
the operating software are permitted.
Do not touch live components or power connections immediately after disconnecting
the MOVIFIT® from the supply voltage because there may still be some charged ca-
pacitors. Wait at least for 1 minute after having switched off the supply voltage.
As soon as supply voltage is present at the MOVIFIT®, the ABOX must be closed i.e.,
the MOVIFIT® EBOX and any hybrid cable connector must be connected and screwed
on.
Do not disconnect the EBOX of the MOVIFIT® or any power plug connectors during
operation. Doing so can lead to dangerous electric arcs forming, which can cause ir-
reparable damage to the unit (fire risk, irreparable contacts).
Important: The MOVIFIT® maintenance switch disconnects only the integrated fre-
quency inverter from the grid. The terminals of the MOVIFIT® unit are still connected to
the line voltage after the maintenance switch is activated.
The unit may still be live and connected to the supply system, even if the operation
LEDs and other display elements are no longer illuminated.
Mechanical blocking or internal safety functions of the unit can cause a motor stand-
still. Eliminating the cause of the problem or performing a reset may result in the drive
re-starting automatically. If this is not permitted for the driven machine for safety rea-
sons, disconnect the unit from the supply system before you start correcting the error.
Caution: Risk of burns: The surface temperature of the MOVIFIT® and the external op-
tions, e.g. the braking resistor heat sink, can exceed 60 °C during operation.
21316996/EN – 12/2014

3
Unit structure
MOVIFIT® FC
Operating Instructions – MOVIFIT® FC 13
3Unit structure
3.1 MOVIFIT® FC MOVIFIT®
FC
MOVIFIT® FC is a decentralized drive controller with integrated frequency inverter that
controls a maximum of up to two gearmotors.
The following figure shows a MOVIFIT® FC unit in size 1 in standard design:
[1]
[2]
4285969931
[1] EBOX (active electronics unit)
[2] ABOX (passive connection unit)
3.1.1 MOVIFIT® FC unit characteristics
• Parameterizable open loop frequency inverter
• Power range from 0.37 to 4 kW (in 2 sizes)
• Integrated energy distribution
• Integrated brake management
• Optional braking resistor
• Optional maintenance switch
• Interface fieldbus interface
PROFIBUS
PROFINET IO
PROFINET POF
EtherNet/IP™
Modbus/TCP
DeviceNet™
• Optional design without fieldbus interface as SBus slave
• Digital inputs/outputs
• CAN/SBus interface
• "Safe torque off" STO function
• S11 PROFIsafe option or S11 safety option with safety-related inputs and outputs
• Simple and fast parameterization via DIP switches (Easy mode)
• Extended parameterization via fieldbus or diagnostic interface (Expert mode)
21316996/EN – 12/2014

3Unit structure
Overview – Connection configuration
Operating Instructions – MOVIFIT® FC
14
3.2 Overview – Connection configuration
The following figures show the MOVIFIT® FC designs that are described in these oper-
ating instructions:
EBOX ABOX Design
MTF...-...-00
Size 1
Size 2
MOVIFIT® FC with integrated fre-
quency inverter
ABOX
MTA...-S02.-...-001)
Standard ABOXwith terminals and cable bushings
MTA...-S42.-...-002)
Hybrid ABOX
with M12 for I/Os
MTA...-S52.-...-001)
Hybrid-ABOX
with M12 for I/Os and bus
MTA...-S53.-...-00/L103)
X31 X30
[A]
Hybrid-ABOX
with POF option L10,
with M12 for I/Os, bus and 24 V output
MTA...-S62.-...-003)
Hybrid ABOX
with M12 for I/Os and push-pull RJ45 for bus
[A] The 3 M12 plug connectors (bus + 24 V) for connecting the POF option L10 are assigned at the factory.
1) In connection with DeviceNet™: Micro-style connector for DeviceNet™ connection
2) Not available in connection with DeviceNet™
3) Not available in connection with DeviceNet™ and PROFIBUS
More designs are listed on the next page.
21316996/EN – 12/2014

3
Unit structure
Overview – Connection configuration
Operating Instructions – MOVIFIT® FC 15
Designs with circular connector (Intercontec) for connecting the motor:
EBOX ABOX Design
MTF...-...-00
Size 1
Size 2
MOVIFIT® FC with integrated fre-
quency inverter
ABOX
MTA...-I55.-...-001)
Hybrid ABOX
with 1 round connector (Intercontec), 1 x downward
motor output, and M12 for I/Os and bus
MTA...-G55.-...-001)
Hybrid ABOX
with 1 circular connector (Intercontec), 1 x motor out-
put at front, and M12 for I/Os and bus
MTA...-I65.-...-002)
Hybrid ABOX
with 1 circular connector (Intercontec), 1 x downward
motor output, M12 for I/Os, push-pull RJ45 for bus
MTA...-G65.-...-002)
Hybrid ABOX
with 1 circular connector (Intercontec), 1 x motor out-
put at front, M12 for I/Os, push-pull RJ45 for bus
1) In connection with DeviceNet™: Micro-style connector for DeviceNet™ connection
2) Not available in connection with DeviceNet™ and PROFIBUS
21316996/EN – 12/2014

3Unit structure
EBOX (active electronics unit)
Operating Instructions – MOVIFIT® FC
16
3.3 EBOX (active electronics unit)
The MOVIFIT® FC EBOX is a closed electronics unit with a communication interface,
digital inputs/outputs (I/Os) and a frequency inverter:
MOVIFIT
®
DI03
DI01
DI02
DI00
DI04
DI05
DI06
DI07
DI08
DI09
DI11
DI12/DO00
DI13/DO01
DI14/DO02
DI15/Do03
SYS-F
BUS-F
24V-C
24V-S
RUN
RUN-PS
ON
1 2 3 4 5 6
S10
MOVIFIT
®
EBOX "MTF...-....-00"
X X
DI03
DI01
DI02
DI00
DI04
DI05
DI06
DI07
DI08
DI09
DI10
DI11
DI12/DO00
DI13/DO01
DI14/DO02
DI15/Do03
SYS-F
BUS-F
24V-C
24V-S
RUN
RUN-PS
MOVIFIT
®
[8]
[1]
[7]
[5]
[A] [B]
DI03
DI01
DI02
DI00
DI04
DI05
DI06
DI07
DI08
DI09
DI10
DI11
DI12/DO00
DI13/DO01
DI14/DO02
DI15/Do03
SYS-F
BUS-F
24V-C
24V-S
RUN
RUN-PS
[2]
[1]
[3]
[4]
[6]
S11
ON
1 2 3 4
18014399322004747
[A] Size 1
[B] Size 2
[1] Central opening/closing mechanism
[2] Operation LEDs for I/Os (can be labeled), communication, and unit status
[3] Outer nameplate of the EBOX
[4] Unit identification of the EBOX
[5] DIP switch S10 for unit functions
[6] DIP switch S11 for IP parameters (only for PROFINET IO, EtherNet/IP™, Mod-
bus/TCP)
[7] Inner nameplate of the EBOX
[8] Connection to ABOX (connection box)
21316996/EN – 12/2014

3
Unit structure
ABOX (passive connection unit)
Operating Instructions – MOVIFIT® FC 17
3.4 ABOX (passive connection unit)
The following figure depicts examples of the MOVIFIT® ABOX:
X
ON
1 2 3 4 5 6 7 8
S2
S1
X
S3
[1]
[13]
[10]
[9] [8]
[7]
[6]
[2] [3] [4]
[11]
[12]
[5]
I
ON
0 OFF
ABOX "MTA...-....-00"
18014399322006411
[1] Mounting rail
[2] Connection to EBOX
[3] Nameplate of complete unit
[4] Inner nameplate of the ABOX
[5] Protection cover
[6] DIP switch S2 for bus address (PROFIBUS and DeviceNet™ design only)
[7] DIP switches S3 for bus termination SBus
[8] DIP switch S1 for bus termination
[9] Maintenance switch (triple lock)
[10] Grounding screws
[11] Unit identification of the ABOX
[12] Outer nameplate of the ABOX
[13] Diagnostic interface underneath the screw plug
21316996/EN – 12/2014

3Unit structure
Hygienicplus variant (optional)
Operating Instructions – MOVIFIT® FC
18
3.5 Hygienicplus design (optional) Hygienicplu
s variant
(optional)
3.5.1 Properties
The Hygienicplus design has the following characteristics:
• IP66 in accordance with EN 60529 and IP69K in accordance with DIN 40050-9
(MOVIFIT® housing closed and all cable bushings sealed according to the relevant
degree of protection)
• Easy-to-clean housing (self-draining design)
• Surface with non-stick properties
• High impact resistance of the surface against mechanical damage
• Compatibility with cleansing agents having the following properties:
– Alkaline
– Acidic
– Disinfectant
Do not mix cleaning and disinfecting agents under any circumstances!
Never mix acids and chloralkalis, as poisonous chlorine gas will result.
Strictly observe the safety instructions of the cleaning agent manufacturer.
• Resistant to temperature fluctuations
• Resistant to condensation due to coated connection boards
INFORMATION
The Hygienicplus design is only available in connection with the standard ABOX.
For other properties of the Hygienicplus design, refer to the next page and to chapter
"Technical Data".
21316996/EN – 12/2014

3
Unit structure
Hygienicplus variant (optional)
Operating Instructions – MOVIFIT® FC 19
The following figure depicts the additional features of MOVIFIT® units in the optional
Hygienicplus design:
Y
X
DI03
DI01
DI02
DI00
DI04
DI05
DI06
DI07
DI08
DI09
DI11
DI12/DO00
DI13/DO01
DI14/DO02
DI15/Do03
SYS-F
BUS-F
24V-C
24V-S
RUN
RUN-PS
MOVIFIT®
X
DI03
DI01
DI02
DI00
DI04
DI05
DI06
DI07
DI08
DI09
DI10
DI11
DI12/DO00
DI13/DO01
DI14/DO02
DI15/Do03
SYS-F
BUS-F
24V-C
24V-S
RUN
RUN-PS
MOVIFIT®
[1] [2] [4] [6]
[5]
[3]
[11]
Y
[9]
[8]
[7]
[10]
ABOX "MTA12...-S02.-...-00"
EBOX "MTF12...-....-00"
9007200067232139
[1] EBOX with special surface treatment (available only in one color)
[2] Signal plug connector with gasket
[3] Gasket between ABOX and cover plate
[4] Power plug connector with gasket
[5] Screws with thread sealant
[6] Replaceable profile seal
[7] Mounting rail with surface coating (only available in one color)
[8] Connection board with increased resistance to moisture condensation (coated)
[9] ABOX with special surface treatment (available only in one color)
[10] In connection with the Hygienicplus design: Generally without maintenance switch
[11] Stainless steel screw plug (available as an option)
21316996/EN – 12/2014

3Unit structure
MOVIFIT® with L10 PROFINET interface SCRJ/POF
Operating Instructions – MOVIFIT® FC
20
3.6 MOVIFIT® with L10 PROFINET interface SCRJ/POF MOVIFIT®
with L10
PROFINET
interface
SCRJ/POF
3.6.1 Unit structure
The following figure shows MOVIFIT® with the L10 PROFINET interface SCRJ/POF
(POF option L10):
[1] [3][2]
[4]
[6]
[5]
9007202682186763
[1] MOVIFIT®
[2] Special mounting rail
[3] POF option L10 (POF = Polymer Optical Fiber)
[4] Status LEDs
[5] X30/X31 connections for PROFINET POF
[6] Electrical connections between the POF option L10 and the ABOX
These connections are installed at the factory.
3.6.2 Functional description
The POF option L10 converts the optical signals that are transmitted via polymer opti-
cal fiber cables (POF) into electrical signals with PROFINET IO protocol and vice ver-
sa.
The POF option L10 makes it possible to connect the ABOX to the optical PROFINET
IO.
21316996/EN – 12/2014