ShelterLogic Shed-in-a-Box User manual

1 05_70443_70743_F3
DESCRIPTION MODEL #
12' x 12' x 8'Shed-in-a-Box ®- Gray 70443
12' x 12' x 8'Shed-in-a-Box ®- Sandstone 70743
5/23/12
Shed-in-a-Box®
Assembly Manual
Before you start: 2 or more individuals recommended for assembly, approximate time 2 hours.
Please read instructions COMPLETELY before assembly. This shelter MUST be securely anchored.
THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED AS A PERMANENT STRUCTURE.
RECOMMENDED TOOLS
OR 7/16"
11mm
1-800-524-9970
1-800-559-6175
Canada:
VIEW AN ONLINE INSTRUCTIONAL VIDEO
OF A GARAGE BEING BUILT!
www.shelterlogic.com/UserFiles/video/index.html
150 Callender Road
Watertown, CT 06795
www.shelterlogic.com

SERVICE HOTLINE
TEL.: [phone] / 95117-0
FAX: [phone]
E-MAIL: [email protected]OM
50NRTH GmbH
STRASSBURGSTR. 14-16
54516 WITTLICH / GERMANY
.50NRTH.com
2 05_70443_70743_F3

2 05_70443_70743_F3

4 05_70443_70743_F3
PARTS LIST
B
A
A
A
x66
01010
10014
x4
10016
x4
x38
03032
x20
10115
10240
x8
10015
x4
12270
x4
x2
801256 x2
801257
x8
10114
800938
x8
x12
01011
802637
x4x8
13201 x8
13202
x1
802600 - Gray
801215 - Sandstone
800318 - Gray
801217 - Sandstone
x1
800317 - Gray
801216 - Sandstone
x1
x2
10066
802129
x4
x3
801258
x4
802694
802693
x4
802695
x6
802130
x10 x8
801209
B

5 05_70443_70743_F3
12270 12270
802130
802130
802130
802130
800938
800938
800938
800938
801209
801209
801209
801209
802694
802693
802694
802693
802637 802637
#10115
#10115
#03032
#03032
#03032
#03032
#10114
#10114
801209
800938
10114
01010
801256
801257
1. ASSEMBLE 2 END RIBS
2. ASSEMBLE 2 MIDDLE RIBS

605_70443_70743_F3
3. CONNECT FRONT END RIB TO A MIDDLE RIB
A. Connect 2 Side Cross Rails (802130) at front end rib with ShelterLock® 3X (800938) as shown.
B. Connect Side Cross Rails at middle rib with ShelterLock® 3X as shown. Leave open for next rib connection.
C. Use Top Cross Rail (801258) to connect ribs at the top.
C
D
D
A
A
B
B
800938 800938
802130
801258
801257
801256
801258
03032
01010
801258
801258
C
01010
01010
03032
801209
801209
802129
802130
802130
01010
03032
802130

7 05_70443_70743_F3
800938
01010
03032
801209
802129
4. CONNECT REMAINING RIBS
A. Use #802129 Side Cross Rails and ShelterLock® 3X (800938) to connect middle ribs as shown.
B. Use #802129 Side Cross Rails and ShelterLock® 3X to connect rear end rib.
C. Use Top Cross Rail (801258) to connect ribs at the top.
802129
802129
801258
801258
A
C
C
B
B
A
800938
03032
802129
802129
801209
01010
801257
03032 01010
801258
801258

8 05_70443_70743_F3
12' 3"
12' 3"
NOTE:
15" Augers are for temporary use only!
For best results ShelterLogic recommends
using our Easy Hooks (#10036 4-pack,
#10035 6-pack, or #10038 8-pack) or 30"
Augers (#10075 4-pack, #10078 6-pack, or
#10079 8-pack) for a stronger, more secure
installation.
Call 1-800-524-9970
or visit
www.shelterlogic.com
for more information.
X
5. SQUARE THE FRAME
A. Place frame in its nal location, which
needs to be as at and level as possible.
B. Measure across opposite corners (X & Y).
These distances must be equal to within
1 inch.
C. Check that the front and rear of the frame
measures 12 ft. 3 in. wide.
Y
6. PROPERLY ANCHOR THE FRAME
A. Anchors must be placed inside shelter at the corner legs. Insert a ¾-inch pipe or steel rod through the eyelet
of the auger and turn the anchor clockwise until the eyelet is sticking out of the ground 1 to 2 inches allowing
room to be anchored to the legs.
B. Thread cable provided through the eyelets of the Anchor as indicated in gure. Secure the cable with the
clamps provided.
WARNING:
Serious injury to persons
or property could result if
cover is installed and shelter
is not anchored and is left
unattended. Shelter must be
securely anchored before use.
TIP If soil is too compact, dig a hole with a shovel or post hole
tool. Set anchor in hole and rell. For a stronger, more
secure installation, ll hole with quick-set cement.

905_70443_70743_F3
7. DOOR PANEL AND BACK PANEL INSTALLATION
A. (1) Hold end panel at the top center with white inner surface facing inside of the shelter. (2) Wrap the edges
of the fabric panel around the end rib and line up the cross rails with the pre made slits in the fabric.
C. (1) Disconnect side cross rail from the end rib. Leave the ShelterLock® 3X attached to the rib with the bolt.
(2) Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel.
(3) Reattach the side cross rail to the end rib.
A1
C1 C2 C3
A2
B. (1) Disconnect top cross rail (the horizontal pipe that runs from front to back along the top) from the end rib.
(2) Pull the end panel over the end rib and bring the end of the cross rail through the cut slit in the panel.
(3) Reattach the top cross rail to the end rib.
B1 B2 B3

10 05_70443_70743_F3
PULL
END PANEL
VIEW FROM
INSIDE
D. At the bottom, where the webbing exits the pocket on each side of end panel, pull webbing as you would a
drawstring to remove the slack. Be careful not to pull the webbing strap out of the webbing pocket.
E. Insert the “S”- Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet
and pull tight. Wind the ratchet so that the webbing overlaps itself. Position the end panel so that it is
centered on the building before fully tightening the end panel.
F. Tighten ratchets, alternating from one side to the other, until the end panel is tight. NOTE: Keep zippers
closed when tightening door panel.
D
EF
7. END PANEL INSTALLATION - continued
PULL
WEBBING
STRAP

11 05_70443_70743_F3
802695
COVER RAILS
8. INSTALLING COVER AND COVER RAILS
A. Lay the cover on the ground next to the frame with inside of the cover (the side with the pipe pockets) facing
down and the webbing on the front and rear of the corner of the building.
B. Pull cover over the frame, making sure to center cover on frame. There should be an equal amount of over-
hang at all four corners.
C. Insert the “S”- Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet
and pull tight. Wind the ratchet so that the webbing overlaps itself.
D. Disassemble cover rails and slide through fabric pockets at each leg and reattach with clamps to each leg.
Repeat this on other side. Push down on cover rails to tighten cover, before tightening bolts completely.
E. Check and tighten Ratchets and Cover Rails monthly to ensure the cover is tight.
NOTE: The ShelterLogic®logo should
be oriented as shown below.
CORRECT
Webbing and Ratchets Securing Cover
FRONT
REAR
INCORRECT
10115
802695
13202
01011
01010
Corner
Leg
10115
802695
802695
13201
Middle
Leg
01010
01011

12 05_70443_70743_F3
9. USING BUNGEES TO HOLD DOOR OPEN (optional)
A. Unzip the door to the height of the grommets.
B. Roll up door section to the height of the grommets.
C. Insert 1 Bungee Cord (#10066) through grommet.
D. Secure Bungee around ball.
A
C D
B