SICK LBR User manual

GB
OPERATING INSTRUCTIONS
LBR
Two-wire 4 … 20 mA/HART

2
Contents
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
Contents
1 About this document ............................................................................................................... 4
1.1 Function ........................................................................................................................... 4
1.2 Target group ..................................................................................................................... 4
1.3 Symbols used................................................................................................................... 4
2 For your safety ......................................................................................................................... 5
2.1 Authorised personnel ....................................................................................................... 5
2.2 Appropriate use................................................................................................................ 5
2.3 Warning about incorrect use............................................................................................. 5
2.4 General safety instructions............................................................................................... 5
2.5 EU conformity................................................................................................................... 6
2.6 NAMUR recommendations .............................................................................................. 6
2.7 Radio license for Europe .................................................................................................. 6
2.8 Radio license for USA ...................................................................................................... 7
2.9 Radio license for Canada ................................................................................................. 7
2.10 Installation and operation in the USA and Canada ........................................................... 9
2.11 Safety instructions for Ex areas ........................................................................................ 9
3 Product description ............................................................................................................... 10
3.1 Conguration.................................................................................................................. 10
3.2 Principle of operation...................................................................................................... 10
3.3 Packaging, transport and storage................................................................................... 11
3.4 Accessories.................................................................................................................... 11
4 Mounting................................................................................................................................. 13
4.1 General instructions ....................................................................................................... 13
4.2 Mounting versions, plastic horn antenna ........................................................................ 13
4.3 Mounting preparations, mounting strap .......................................................................... 16
4.4 Mounting instructions ..................................................................................................... 17
5 Connecting to power supply................................................................................................. 28
5.1 Preparing the connection ............................................................................................... 28
5.2 Connecting..................................................................................................................... 29
5.3 Wiring plan, single chamber housing.............................................................................. 30
5.4 Switch-on phase............................................................................................................. 31
6 Set up with the display and adjustment module ................................................................ 32
6.1 Insert display and adjustment module............................................................................ 32
6.2 Adjustment system......................................................................................................... 33
6.3 Measured value indication - Selection of national language........................................... 34
6.4 Parameter adjustment - Quick setup .............................................................................. 35
6.5 Parameter adjustment - Extended adjustment................................................................ 35
6.6 Saving the parameterisation data................................................................................... 49
7 Setup with PACTware............................................................................................................. 50
7.1 Connect the PC.............................................................................................................. 50
7.2 Parameter adjustment .................................................................................................... 50
7.3 Saving the parameterisation data................................................................................... 50
8 Diagnosis, asset management and service ........................................................................ 51
8.1 Maintenance .................................................................................................................. 51
8.2 Measured value and event memory ............................................................................... 51

3
Contents
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
8.3 Asset Management function........................................................................................... 52
8.4 Rectify faults................................................................................................................... 55
8.5 Exchanging the electronics module................................................................................ 58
8.6 How to proceed if a repair is necessary.......................................................................... 58
9 Dismount................................................................................................................................. 59
9.1 Dismounting steps.......................................................................................................... 59
9.2 Disposal ......................................................................................................................... 59
10 Supplement ............................................................................................................................ 60
10.1 Technical data ................................................................................................................ 60
10.2 Radio astronomy stations............................................................................................... 71
10.3 Dimensions .................................................................................................................... 71
10.4 Trademark ...................................................................................................................... 81
Safety instructions for Ex areas
TakenoteoftheExspecicsafetyinstructionsforExapplications.
These instructions are attached as documents to each instrument
with Ex approval and are part of the operating instructions.
Editing status: 2020-04-21

4
1 About this document
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
1 About this document
1.1 Function
This instruction provides all the information you need for mounting,
connection and setup as well as important instructions for mainte-
nance,faultrectication,theexchangeofpartsandthesafetyofthe
user. Please read this information before putting the instrument into
operation and keep this manual accessible in the immediate vicinity
of the device.
1.2 Target group
This operating instructions manual is directed to trained personnel.
Thecontentsofthismanualmustbemadeavailabletothequalied
personnel and implemented.
1.3 Symbols used
Information, note, tip: This symbol indicates helpful additional infor-
mation and tips for successful work.
Note: This symbol indicates notes to prevent failures, malfunctions,
damage to devices or plants.
Caution: Non-observance of the information marked with this symbol
may result in personal injury.
Warning: Non-observance of the information marked with this symbol
may result in serious or fatal personal injury.
Danger: Non-observance of the information marked with this symbol
results in serious or fatal personal injury.
Ex applications
This symbol indicates special instructions for Ex applications.
• List
The dot set in front indicates a list with no implied sequence.
1 Sequence of actions
Numbers set in front indicate successive steps in a procedure.
Battery disposal
This symbol indicates special information about the disposal of bat-
teries and accumulators.

5
2 For your safety
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
2 For your safety
2.1 Authorised personnel
All operations described in this documentation must be carried out
onlybytrained,qualiedpersonnelauthorisedbytheplantoperator.
During work on and with the device, the required personal protective
equipment must always be worn.
2.2 Appropriate use
LBR is a sensor for continuous level measurement.
Youcannddetailedinformationabouttheareaofapplicationin
chapter "Product description".
Operational reliability is ensured only if the instrument is properly
usedaccordingtothespecicationsintheoperatinginstructions
manual as well as possible supplementary instructions.
2.3 Warning about incorrect use
Inappropriate or incorrect use of this product can give rise to applica-
tion-specichazards,e.g.vesseloverllthroughincorrectmounting
or adjustment. Damage to property and persons or environmental
contamination can result. Also, the protective characteristics of the
instrument can be impaired.
2.4 General safety instructions
This is a state-of-the-art instrument complying with all prevailing
regulations and directives. The instrument must only be operated in a
technicallyawlessandreliablecondition.Theoperatorisresponsi-
ble for the trouble-free operation of the instrument. When measuring
aggressive or corrosive media that can cause a dangerous situation
if the instrument malfunctions, the operator has to implement suitable
measures to make sure the instrument is functioning properly.
The safety instructions in this operating instructions manual, the na-
tional installation standards as well as the valid safety regulations and
accident prevention rules must be observed by the user.
For safety and warranty reasons, any invasive work on the device
beyond that described in the operating instructions manual may be
carried out only by personnel authorised by the manufacturer. Arbi-
traryconversionsormodicationsareexplicitlyforbidden.Forsafety
reasons,onlytheaccessoryspeciedbythemanufacturermustbe
used.
To avoid any danger, the safety approval markings and safety tips on
the device must also be observed.
The low transmitting power of the radar sensor is far below the inter-
nationally approved limits. No health impairments are to be expected
with intended use.The band range of the transmission frequency can
be found in chapter "Technical data".

6
2 For your safety
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
2.5 EU conformity
ThedevicefullsthelegalrequirementsoftheapplicableEUdirec-
tives.ByaxingtheCEmarking,weconrmtheconformityofthe
instrument with these directives.
The EU conformity declaration can be found on our homepage.
2.6 NAMUR recommendations
NAMUR is the automation technology user association in the process
industry in Germany. The published NAMUR recommendations are
acceptedasthestandardineldinstrumentation.
ThedevicefullstherequirementsofthefollowingNAMURrecom-
mendations:
• NE 43 – Signal level for fault information from measuring transduc-
ers
• NE53–Compatibilityofelddevicesanddisplay/adjustment
components
• NE107–Self-monitoringanddiagnosisofelddevices
For further information see www.namur.de.
2.7 Radio license for Europe
The instrument was tested according to the latest issue of the follow-
ingharmonizedstandards:
• EN 302372 - Tank Level Probing Radar
• EN 302729 - Level Probing Radar
It is hence approved for use inside and outside closed vessels in
countries of the EU.
Use is also approved in EFTA countries, provided the respective
standards have been implemented.
For operation inside of closed vessels, points a to f in annex E of
EN302372mustbefullled.
For operation outside of closed vessels, the following conditions must
befullled:
• The instrument must be stationary mounted and the antenna
directed vertically downward
• The instrument may only be used outside closed vessels in the
version with G1½ or 1½ NPT thread with integrated horn antenna.
• The mounting location must be at least 4 km away from radio
astronomy stations, unless special permission was granted by the
responsible national approval authority
• When installed within 4 to 40 km of a radio astronomy station,
the instrument must not be mounted higher than 15 m above the
ground.
A list of the respective radio astronomy stations can be found in chap-
ter "Appendix" of the operating instructions.

7
2 For your safety
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
2.8 Radio license for USA
This approval is only valid for USA. Hence the following text is only
available in the English language:
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
• This device may not cause interference, and
• This device must accept any interference, including interference
that may cause undesired operation of the device
This device is approved for unrestricted use only inside closed,
stationary vessels made of metal or concrete. From electronics index
.-03theuseincontainersmadeofreinforcedberglassisalsopermit-
ted.
For operation outside of closed vessels, the following conditions must
befullled:
• This device shall be installed and maintained to ensure a verti-
cally downward orientation of the transmit antenna's main beam.
Furthermore, the use of any mechanism that does not allow the
main beam of the transmitter to be mounted vertically downward is
prohibited.
• Operation of the instrument is only permitted with thread G1½ or
1½ NPT with integrated horn antenna.
• Thisdeviceshallbeinstalledonlyatxedlocations.TheLPR
device shall not operate while being moved or while inside a mov-
ing container.
• Hand-held applications are prohibited.
• Marketing to residential consumers is prohibited.
Changesormodicationsnotexpresslyapprovedbythemanufac-
turer could void the user’s authority to operate this equipment.
2.9 Radio license for Canada
This approval is only valid for Canada. Hence the following texts are
only available in the English/French language:
This device complies with Industry Canada's license-exempt RSS
standard(s). Operation is subject to the following conditions:
• This device may not cause interference, and
• This device must accept any interference, including interference
that may cause undesired operation of the device
This device has been approved for both closed containers and open-
air environments with the following limitations:
• ClosedContainers:Forinstallationsutilizingatiltduringinstalla-
tion: This device is limited to installation in a completely enclosed
container made of metal or concrete to prevent RF emissions,
which can otherwise interfere with aeronautical navigation, the
maximum approved tilt angel is 10°. From electronics index .-03
theuseincontainersmadeofreinforcedberglassisalsopermit-
ted.

8
2 For your safety
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
• Open Air Environment: For operation outside of closed vessels,
thefollowingconditionmustbefullled:Thisdeviceshallbe
installed and maintained to ensure a vertically downward orienta-
tion of the transmit antenna's main beam. Furthermore, the use of
any mechanism that does not allow the main beam of the transmit-
ter to be mounted vertically downward is prohibited.
• Operation of the instrument outside of closed vessels is only per-
mitted with G1½ or 1½ NPT with integrated horn antenna.
• The installation of the LPR/TLPR device shall be done by trained
installers, in strict compliance with the manufacturer's instructions.
• Thisdeviceshallbeinstalledonlyatxedlocations.TheLPR
device shall not operate while being moved or while inside a mov-
ing container.
• Hand-held applications are prohibited.
• Marketing to residential consumers is prohibited.
• The use of this device is on a "no-interference, no-protection"
basis.That is, the user shall accept operations of high-powered
radar in the same frequency band which may interfere with or
damage this device.
• However, devices found to interfere with primary licensing opera-
tions will be required to be removed at the user's expense.
• The installer/user of this device shall ensure that it is at least 10 km
from the Dominion Astrophysical Radio Observatory (DRAO) near
Penticton, British Columbia. The coordinates of the DRAO are
latitude49°19′15″Nandlongitude119°37′12″W.Fordevicesnot
meeting this 10 km separation (e.g., those in the Okanagan Valley,
British Columbia,) the installer/user must coordinate with, and
obtain the written concurrence of, the Director of the DRAO before
the equipment can be installed or operated.The Director of the
DRAO may be contacted at 250-497-2300 (tel.)or 250-497-2355
(fax). (Alternatively, the Manager, Regulatory Standards, Industry
Canada, may be contacted.)
Le présent appareil est conforme aux CNR d’Industrie Canada ap-
plicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux conditions suivantes :
• L’appareil ne doit pas produire de brouillage; et
• L’utilisateur de l’appareil doit accepter tout brouillage radioélect-
rique subi, même si le brouillage est susceptible d’en compromet-
tre le fonctionnement.
Cet appareil est homologué pour une utilisation dans les cuves fer-
mées et les environnements ouverts avec les restrictions suivantes :
• Cuves fermées : Pour les installations impliquant une inclinaison
lors de l'installation : cet appareil ne doit être installé que dans
une cuve totalement fermée en métal ou en béton, pour empêcher
les émissions RF susceptibles d'interférer avec la navigation
aéronautique. L'angle d'inclinaison maximum autorisé est de 10°.
De l'indice électronique .-03, l'utilisation dans des conteneurs
fabriquésenbredeverreestégalementpermise.
• Environnement ouvert : Pour l'utilisation hors des cuves fermées,
la condition suivante doit être remplie : L'appareil doit être installé

9
2 For your safety
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
et entretenu de manière à garantir une orientation verticale vers
le bas du faisceau principal de l’antenne émettrice. De plus,
l’utilisation de tout mécanisme ne permettant pas l’orientation ver-
ticale vers le bas du faisceau principal de l’émetteur est interdite
• Il est uniquement autorisé d'utiliser la version d'appareil avec le
letageG1½ou1½NPTenenvironnementsouvertes.
• L’installationd’undispositifLPRouTLPRdoitêtreeectuée
pardesinstallateursqualiés,enpleineconformitéavecles
instructions du fabricant.
• Cetappareilnedoitêtreinstalléqu'àdesemplacementsxes.
L’appareil LPR ne doit pas être utilisé pendant qu’il est en train
d’être déplacé ou se trouve dans un conteneur en mouvement.
• Les applications portables sont interdites.
• La vente à des particuliers est interdite.
• Ce dispositif ne peut être exploité qu'en régime de non-brouillage
et de non-protection, c'est-à-dire que l'utilisateur doit accepter que
des radars de haute puissance de la même bande de fréquences
puissent brouiller ce dispositif ou même l'endommager.
• D'autre part, les capteurs de niveau qui perturbent une exploita-
tion autorisée par licence de fonctionnement principal doivent être
enlevés aux frais de leur utilisateur.
• La personne qui installe/utilise ce capteur de niveau doit s'assurer
qu'il se trouve à au moins 10 km de l'Observatoire fédéral de
radioastrophysique (OFR) de Penticton en Colombie-Britannique.
Lescoordonnéesdel'OFRsont:latitudeN49°19′15″,longitude
O119°37′12″.Lapersonnequiinstalle/utiliseundispositifne
pouvant respecter cette distance de 10 km (p. ex. dans la vallée
de l'Okanagan [Colombie-Britannique]) doit se concerter avec le
directeurdel'OFRand’obtenirdesapartuneautorisationécrite
avant que l'équipement ne puisse être installé ou mis en marche.
Le directeur de l'OFR peut être contacté au 250-497-2300 (tél.) ou
au 250-497-2355 (fax). (Le Directeur des Normes réglementaires
d'Industrie Canada peut également être contacté).
2.10 Installation and operation in the USA and
Canada
This information is only valid for USA and Canada. Hence the follow-
ing text is only available in the English language.
Installations in the US shall comply with the relevant requirements of
the National Electrical Code (ANSI/NFPA 70).
Installations in Canada shall comply with the relevant requirements of
the Canadian Electrical Code
A Class 2 power supply unit has to be used for the installation in the
USA and Canada.
2.11 Safety instructions for Ex areas
For Ex applications, only devices with corresponding Ex approval may
beused.ObservetheEx-specicsafetyinstructions.Thesearean
integral part of the operating instructions and are enclosed with every
device with Ex approval.

10
3 Product description
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
3 Product description
3.1 Conguration
This operating instructions manual applies to the following instrument
versions:
• Hardware version from 1.0.3
• Software version from 1.3.2
The scope of delivery encompasses:
• LBR radar sensor
• Hexagon socket wrench (for instruments with swivel holder)
The further scope of delivery encompasses:
• Documentation
– Quick setup guide LBR
– Instructions for optional instrument features
– Ex-specic"Safety instructions" (with Ex versions)
– Ifnecessary,furthercerticates
Information:
Optional instrument features are also described in this operating
instructions manual.The respective scope of delivery results from the
orderspecication.
3.2 Principle of operation
The LBR is a radar sensor for continuous level measurement of bulk
solidsunderdierentprocessconditions.
It is ideal for level measurement in very high silos, large bunkers and
segmented vessels. The very good signal focussing ensures a simple
setup and reliable measurement.
TheLBRisavailablewithdierentantennasystems:
1 2 3
Fig. 1: Antenna systems LBR
1 Metal-jacketed lens antenna
2 Plastic horn antenna
3 Thread with integrated horn antenna
Scope of this operating
instructions
Scope of delivery
Application area

11
3 Product description
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
The instrument emits a continuous, frequency-modulated radar signal
throughitsantenna.Theemittedsignalisreectedbythemedium
andreceivedbytheantennaasanechowithmodiedfrequency.The
frequency change is proportional to the distance and is converted into
the level.
3.3 Packaging, transport and storage
Your instrument was protected by packaging during transport. Its
capacity to handle normal loads during transport is assured by a test
based on ISO 4180.
The packaging consists of environment-friendly, recyclable card-
board. For special versions, PE foam or PE foil is also used. Dispose
of the packaging material via specialised recycling companies.
Transport must be carried out in due consideration of the notes on the
transport packaging. Nonobservance of these instructions can cause
damage to the device.
The delivery must be checked for completeness and possible transit
damage immediately at receipt. Ascertained transit damage or con-
cealed defects must be appropriately dealt with.
Up to the time of installation, the packages must be left closed and
stored according to the orientation and storage markings on the
outside.
Unless otherwise indicated, the packages must be stored only under
the following conditions:
• Not in the open
• Dry and dust free
• Not exposed to corrosive media
• Protected against solar radiation
• Avoiding mechanical shock and vibration
• Storage and transport temperature see chapter "Supplement -
Technical data - Ambient conditions"
• Relative humidity 20 … 85 %
With instrument weights of more than 18 kg (39.68 lbs) suitable and
approved equipment must be used for lifting and carrying.
3.4 Accessories
The instructions for the listed accessories can be found in the down-
load area on our homepage.
The display and adjustment module is used for measured value indi-
cation, adjustment and diagnosis.
The integrated Bluetooth module (optional) enables wireless adjust-
ment via standard adjustment devices.
Functional principle
Packaging
T
ransport
Transport inspection
Storage
Storage and transport
temperature
Lifting and carrying
Display and adjustment
module

12
3 Product description
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
The electronics module LBR is a replacement part for radar sensors
LBR.
Electronics module

13
4 Mounting
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
4 Mounting
4.1 General instructions
Protect your instrument against moisture ingress through the following
measures:
• Use a suitable connection cable (see chapter "Connecting to
power supply")
• Tighten the cable gland or plug connector
• Lead the connection cable downward in front of the cable entry or
plug connector
This applies mainly to outdoor installations, in areas where high
humidity is expected (e.g. through cleaning processes) and on cooled
or heated vessels.
Note:
Makesurethatthedegreeofcontaminationspeciedinchapter
"Technical data" meets the existing ambient conditions.
Note:
Make sure that during installation or maintenance no moisture or dirt
can get inside the instrument.
To maintain the housing protection, make sure that the housing lid is
closed during operation and locked, if necessary.
Note:
For safety reasons, the instrument must only be operated within the
permissibleprocessconditions.Youcannddetailedinformationon
the process conditions in chapter "Technical data" of the operating
instructions or on the type label.
Hence make sure before mounting that all parts of the instrument ex-
posed to the process are suitable for the existing process conditions.
These are mainly:
• Active measuring component
• Processtting
• Process seal
Process conditions in particular are:
• Process pressure
• Process temperature
• Chemical properties of the medium
• Abrasionandmechanicalinuences
The mounting position and orientation of the sensor must take into ac-
count the limitations in chapter "For your safety", "Radio approval for
USA" "Radio approval for Canada" of this operating instructions.
4.2 Mounting versions, plastic horn antenna
The optional mounting strap allows simple mounting of the instrument
on a wall, ceiling or boom. Especially in the case of open vessels, this
Protection against mois-
ture
Process conditions
Radio license for USA/
Canada
Mounting strap

14
4 Mounting
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
isasimpleandeectivewaytoalignthesensortothesurfaceofthe
bulk solid material.
The following versions are available:
• Length 300 mm
• Length 170 mm
The instrument is normally mounted vertically with a bracket on the
ceiling.
This allows swivelling the sensor up to 180° for optimal orientation
and rotating for optimal connection.
Fig. 2: Ceiling mounting via the mounting strap with length 300 mm
Asanalternativethestrapmountingiscarriedouthorizontallyor
obliquely.
> 200 mm
(7.87")
Fig. 3: Wall mounting horizontally via the mounting strap with length 170 mm
Mounting strap - Ceiling
mounting
Mounting strap - Wall
mounting

15
4 Mounting
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
Fig. 4: Wall mounting with inclined wall via the mounting strap with length
300 mm
Two versions are available for mounting the instrument on a socket:
• Combicompressionange
• Adapterange
Combicompressionange
Thecombicompressionangeissuitablefordierentvesselanges
DN 80, ASME 3" and JIS 80. It comes not sealed against the radar
sensorandcanthusonlybeusedunpressurized.Itcanberetrotted
oninstrumentswithsinglechamberhousing,retrottingtoadouble
chamber housing is not possible.
1
Fig. 5: Combi compression ange
1 Combi compression ange
Adapterange
TheadapterangeisavailablefromDN100,ASME4"andJIS100.It
is permanently connected with the radar sensor and sealed.
Flange

16
4 Mounting
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
3
1
2
Fig. 6: Adapter ange
1 Connection screw
2 Adapter ange
3 Process seal
4.3 Mounting preparations, mounting strap
The mounting strap is supplied unassembled (optionally) and must be
screwed to the sensor before setup with three hexagon socket screws
M5 x 10 and spring washers. Max. torque, see chapter "Technical
data".Requiredtools:Allenwrenchsize4.
Therearetwodierentvariantsofscrewingthestraptothesensor,
see following illustration:
1 2
Fig. 7: Mounting strap for screwing to the sensor
1 For angle of inclination in steps
2 For angle of inclination, innitely variable
Depending on the selected variant, the sensor can be rotated in the
strap:
• Single chamber housing
– Angle of inclination in three steps 0°, 90° and 180°
– Angleofinclination180°,innitelyvariable
• Double chamber housing
– Angle of inclination in two steps 0° and 90°
– Angleofinclination90°,innitelyvariable

17
4 Mounting
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
Fig. 8: Adjustment of the angle of inclination
Fig. 9: Turning by fastening in the centre
4.4 Mounting instructions
Radar sensors for level measurement emit electromagnetic waves.
Thepolarizationisthedirectionoftheelectricalcomponentofthese
waves.
Thepolarizationdirectionismarkedbyanoseonthehousing,see
following drawing:
1
Fig. 10: Position of the polarisation
1 Nose for marking the direction of polarisation
Note:
Whenthehousingisrotated,thedirectionofpolarizationchanges
andhencetheinuenceofthefalseechoonthemeasuredvalue.
Please keep this in mind when mounting or making changes later.
Mount the sensor at least 200 mm (7.874 in) away from the vessel
wall.
Polarisation
Installation position

18
4 Mounting
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
200 mm
(7.87
")
Fig. 11: Mounting the radar sensor on the vessel top
If you cannot maintain this distance, you should carry out a false
signal suppression during setup. This applies particularly if buildup on
the vessel wall is expected. In such cases, we recommend repeating
the false signal suppression at a later date with existing buildup.
Theinstrumentshouldnotbemountedtooclosetotheinowing
medium, as the radar signal could be disrupted.
Silowithllingfromtop
Theoptimalmountingpositionisoppositethellingaperture.Toavoid
heavysoiling,thedistancetoanylterordustexhaustershouldbeas
large as possible.
Fig. 12: Mounting of the radar sensor with inowing medium
Silowithlaterallling
Inbulksolidssiloswithlateralpneumaticllingtheinstrumentshould
notbemountedabovethellingstream,astheradarsignalwillbe
disrupted.Theoptimalmountingpositionistothesideofthelling
aperture.Toavoidheavysoiling,thedistancetoanylterordust
exhauster should be as large as possible.
Inowingmedium

19
4 Mounting
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
Fig. 13: Mounting of the radar sensor with inowing medium
For socket mounting, the socket should be as short as possible and
itsendrounded.Thisreducesfalsereectionsfromthesocket.
With threaded connection, the antenna end should protrude at least
5 mm (0.2 in) out of the socket.
ca. 5 mm
21 3
Fig. 14: Recommended socket mounting with dierent versions of LBR
1 Metal-jacketed lens antenna
2 Plastic horn antenna
3 Thread with integrated horn antenna
Mounting socket

20
4 Mounting
LBR • Two-wire 4 … 20 mA/HART
62273-EN-200520
Ifthereectivepropertiesofthemediumaregood,youcanmount
LBR on sockets longer than the antenna.The socket end should be
smooth and burr-free, if possible also rounded.
Note:
When mounting on longer sockets, we recommend carrying out a
false signal suppression (see chapter "Parameter adjustment").
Youwillndrecommendedvaluesforsocketheightsinthefollowing
illustration or the tables.The values come from typical applications.
Deviating from the proposed dimensions, also longer sockets are
possible, however the local conditions must be taken into account.
d
h
d
h
d
h
21 3
Fig. 15: Socket mounting with deviating socket dimensions with dierent ver-
sions of LBR
1 Metal-jacketed lens antenna
2 Plastic horn antenna
3 Thread with integrated horn antenna
Metal-jacketed lens antenna
Socket diameter d Socket length h
100 mm 4" ≤500mm ≤19.7in
150 mm 6" ≤800mm ≤31.5in
Plastic horn antenna
Socket diameter d Socket length h
80 mm 3" ≤400mm ≤15.8in
100 mm 4" ≤500mm ≤19.7in
150 mm 6" ≤800mm ≤31.5in
Thread with integrated horn antenna
Socket diameter d Socket length h
40 mm 1½" ≤150mm ≤5.9in
50 mm 2" ≤200mm ≤7.9in