Siemens SIMATIC ET 200SP TM ECC 2xPWM ST User manual

SIMATIC
ET 200SP
Technology module TM ECC
2xPWM ST (6FE1242-6TM10-
0BB1)
Manual
04/2018
A5E42681298B
-AA
Preface
Documentation guide
1
Product overview
2
Wiring
3
Configuring/address space
4
Programming
5
Interrupts/diagnostic
messages
6
Technical specifications
7

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E42681298B-AA
Ⓟ
05/2018 Subject to change
Copyright © Siemens AG 2017 - 2018.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury
may
result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)
Manual, 04/2018, A5E42681298B-AA 3
Preface
Preface
Purpose of the documentation
This manual contains module-specific information on wiring, diagnostics as well as the
technical specifications of the technology module.
General information on installation and commissioning of the ET 200SP is available in the
ET 200SP System Manual.
Conventions
Please take into account the notes marked as follows:
Note
A note contains important information on the product described in t
his documentation, its
handling and to a section of the documentation to which you should pay particular attention.
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens' products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be
connected to an enterprise network or the internet if and to the extent such a connection is
necessary and only when appropriate security measures (e.g. firewalls and/or network
segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit.
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure
to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under.

Preface
Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)
4Manual, 04/2018, A5E42681298B-AA
See also
IndustrialSecurity (http://www.siemens.com/industrialsecurity)
http://support.automation.siemens.com (http://support.automation.siemens.com)

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)
Manual, 04/2018, A5E42681298B-AA 5
Table of contents
Preface ................................................................................................................................................... 3
1 Documentation guide .............................................................................................................................. 7
2 Product overview .................................................................................................................................. 11
2.1 Properties................................................................................................................................11
3 Wiring ................................................................................................................................................... 17
3.1 Terminal assignment and power supply .................................................................................17
3.2 Connection examples .............................................................................................................25
4 Configuring/address space.................................................................................................................... 31
4.1 Configuring..............................................................................................................................31
4.2 Reaction to CPU STOP ..........................................................................................................32
4.3 Required I/O address space ...................................................................................................32
4.4 Parameter ...............................................................................................................................33
4.5 Control and feedback interface...............................................................................................35
4.5.1 Assignment of the control interface ........................................................................................35
4.5.2 Assignment of the feedback Interface ....................................................................................37
5 Programming ........................................................................................................................................ 41
5.1 General information ................................................................................................................41
5.2 "ECC4100" functions ..............................................................................................................41
5.3 FC ECC4100 parameters .......................................................................................................42
6 Interrupts/diagnostic messages............................................................................................................. 47
6.1 Status and error displays ........................................................................................................47
6.2 Interrupts.................................................................................................................................50
6.3 Diagnostics alarms..................................................................................................................50
6.4 Device defect ..........................................................................................................................52
7 Technical specifications ........................................................................................................................ 53
7.1 Technical specifications ..........................................................................................................53
Index..................................................................................................................................................... 57

Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)
Manual, 04/2018, A5E42681298B-AA 7
Documentation guide
1
The documentation for the SIMATIC S7-1500 automation system and the SIMATIC
ET 200MP distributed I/O system is arranged into three areas.
This arrangement enables you to access the specific content you require.
Basic information
The System Manual and Getting Started describe in detail the configuration, installation,
wiring and commissioning of the SIMATIC S7-1500 and ET 200MP systems. The STEP 7
online help supports you in the configuration and programming.
Device information
Product manuals contain a compact description of the module-specific information, such as
properties, wiring diagrams, characteristics and technical specifications.
General information
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
S7-1500 and ET 200MP systems, e.g. diagnostics, communication, motion control, Web
server, OPC UA.
You can download the documentation free of charge from the Internet
(http://w3.siemens.com/mcms/industrial-automation-systems-simatic/en/manual-
overview/Pages/Default.aspx).
Changes and supplements to the manuals are documented in a Product Information.

Documentation guide
Technology module TM ECC 2xPWM ST (6FE1242-6TM10-0BB1)
8Manual, 04/2018, A5E42681298B-AA
You can download the product information free of charge from the Internet
(https://support.industry.siemens.com/cs/us/en/view/68052815).
Manual Collection S7-1500/ET 200MP
The Manual Collection contains the complete documentation on the SIMATIC S7-1500
automation system and the ET 200MP distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/86140384).
SIMATIC S7-1500 comparison list for programming languages
The comparison list contains an overview of which instructions and functions you can use for
which controller families.
You can find the comparison list on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/86630375).
"mySupport"
With "mySupport", your personal workspace, you make the best out of your Industry Online
Support.
In "mySupport", you can save filters, favorites and tags, request CAx data and compile your
personal library in the Documentation area. In addition, your data is already filled out in
support requests and you can get an overview of your current requests at any time.
You must register once to use the full functionality of "mySupport".
You can find "mySupport" on the Internet (https://support.industry.siemens.com/My/ww/en).
"mySupport" - Documentation
In the Documentation area in "mySupport" you can combine entire manuals or only parts of
these to your own manual.
You can export the manual as PDF file or in a format that can be edited later.
You can find "mySupport" - Documentation on the Internet
(http://support.industry.siemens.com/My/ww/en/documentation).
"mySupport" - CAx data
In the CAx data area in "mySupport", you can access the current product data for your CAx
or CAe system.
You configure your own download package with a few clicks.