SitOnit Seating WIT User manual

WIT
ASSEMBLY INSTRUCTIONS
Gone are the days when you clock in, stay in your cubicle and clock out. Dynamic
environments call for adaptable seating that rolls with the punches. Our Wit family does
exactly that. Because this is a design inspired by truths about how people work.
C684 Rev. E

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.sitonit.net
WIT ASSEMBLY INSTRUCTIONS
COMPONENT LIST
COMPONENTS
REQUIRED TOOLS
Basic Mechanism
• ⁵⁄₁₆" × 1" Screw (4)
• ⁵⁄₁₆" Washer (4)
• Back Assembly (1)
• Seat Assembly (1)
• Base Assembly (1)
• Cylinder (1)
• Optional Stool Base Foot Ring (1)
Swivel Tilt Mechanism
• ⁵⁄₁₆" × 1" Screw (4)
• ⁵⁄₁₆" Washer (4)
• Back Assembly (1)
• Seat Assembly (1)
• Base Assembly (1)
• Cylinder (1)
Standard Synchro Mechanism
• ⁵⁄₁₆" × 1" Screw (3)
• ⁵⁄₁₆" Washer (3)
• Back Assembly (1)
• Seat Assembly (1)
• Base Assembly (1)
• Cylinder (1)
¹⁄₄" Hex L-Key
Task Chair Base Option Stool Base Option
Basic Mechanism
Seat Assembly
BASE
OR OR
OR
Back Assembly
⁵⁄₁₆" × 1" Screw ⁵⁄₁₆" Washer
CylinderCylinder Foot Ring
Base AssemblyBase Assembly
HARDWARE KIT
⁵⁄₁₆" × 1" Screws
⁵⁄₁₆" Washers
HARDWARE KIT
⁵⁄₁₆" × 1" Screws
⁵⁄₁₆" Washers
HARDWARE KIT
⁵⁄₁₆" × 1" Screws
⁵⁄₁₆" Washers
Standard Synchro Mechanism
Swivel Tilt Mechanism
1:1 SCALE
MECHANISM
(Mechanism will come attached to seat. Hardware kit is packaged separately.)
2

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.sitonit.net
WIT ASSEMBLY INSTRUCTIONS
STEPS
1
3
2
BASIC MECHANISM
1. Place seat/mechanism assembly on a rm, at surface.
2. Place back assembly over hole pattern.
3. Secure back assembly by tightening four screws and four washers using a ¼" hex L-key to a minimum
torque of 150 in-lbs.
⁵⁄₁₆" × 1" Screw
⁵⁄₁₆" Washer
Back Assembly
Seat Assembly
3

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.sitonit.net
WIT ASSEMBLY INSTRUCTIONS
STEPS
1. Place seat/mechanism assembly on a rm, at surface.
2. Place back assembly over hole pattern.
3. Secure back assembly by tightening four screws and four washers using a ¼" hex L-key to a
minimum torque of 150 in-lbs.
1SWIVEL TILT MECHANISM
⁵⁄₁₆" × 1" Screw
⁵⁄₁₆" Washer
Back Assembly
Seat Assembly
3
2
4

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.sitonit.net
WIT ASSEMBLY INSTRUCTIONS
STEPS
1
2
1. Place seat/mechanism assembly on a rm, at surface. Locate yoke by sliding in bracket and
following hole pattern.
2. Secure yoke by tightening three screws and washers using a ¼" hex L-key to a minimum torque
of 150 in-lbs.
STANDARD SYNCHRO MECHANISM
⁵⁄₁₆" × 1" Screw
⁵⁄₁₆" Washer
Yoke
Bracket
Back Assembly
Seat Assembly
5

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.sitonit.net
WIT ASSEMBLY INSTRUCTIONS
STEPS
1BASE INSTALLATION
1. Slide the cylinder (for task or for stool) into the center of the base and give it a push to seat it into position.
2. For stool version: Slide the foot ring over the cylinder until it is in the desired position. Follow the instructions in
the foot ring package to tighten into place.
3. With the base assembly sitting on the oor, rmly hold the seat and back assembly, align the mechanism's
cylinder mounting hole with the top of the cylinder and push in place until seated. The cylinder is seated when
you can lift the chair and the cylinder stays attached to the mechanism.
Cylinder
Base Assembly
Base Assembly
2
3
Cylinder
Seat Assembly
Back Assembly
Foot Ring
6