SitOnit Seating Parallon User manual

Parallon
POWER READY MEETING,
CAFÉ AND OCCASIONAL DISC-BASE TABLE
C6621 Rev A |www.sitonit.net |1
ASSEMBLY INSTRUCTIONS
Everything to the table.
When you want cohesion in spaces large,
small, shared or separate, there’s Parallon.
It’s a single collection with a singular look,
oering an array of choices for a variety of
environments—and all the features to t.
Ensure design is never a distraction in the
places where everyone needs to focus. Our
Parallon line of café and occasional tables
provides a unied and streamlined look from
room to room.

2 |www.sitonit.net |C6620 Rev A
Parallon MEETING/CAFÉ/OCCASIONAL TABLE ASSEMBLY INSTRUCTIONS
Failure to follow instructions could result in product failure or
potential injury.
Do not apply sudden weight to table.
Do not exceed 200 lb static load weight capacity.
• Cordless Drill/Driver
• #3 Phillips Bit
• Hex Shank to ¼" Square Drive
Adapter
• 1⁄2" Hex Socket, 1⁄4" Drive
• 3⁄8" Hex Socket, 1⁄4" Drive
Recommended Tools
Cordless
Drill/Driver
#3 Phillips Bit
Hex Shank to
1⁄4" Square Drive Adapter
1⁄2" Hex Socket,
1⁄4" Drive
3⁄8" Hex Socket,
1⁄4" Drive
CAUTION
Read the entire instruction manual before you start installation and
assembly. If you have any questions regarding any of the instructions or
warnings, please contact your local distributor for assistance.
To report any issues with this product, contact our customer experience
team at: [phone] or [email protected].

C6620 Rev A |www.sitonit.net |3
Parallon MEETING/CAFÉ/OCCASIONAL TABLE ASSEMBLY INSTRUCTIONS
• Tabletop (1, round, square, rectangle
or racetrack)
• Column (1)
• Disc Base (1)
• Power Cone (1)
• Power Module (1, optional)
• Grommet (1)
• Pack A:
•#12 × 1" Screw (8)
• Pack B:
•5⁄16" × 1½" Bolt (2)
• Pack P:
•¼" x 1⁄2" Bolt (4)
#12 x 1" Screws
PACK A
Parts
Column
5⁄16 x 1½" Bolts
PACK B
1⁄4"x 1⁄2" Bolts
PACK P
Power Cone
Disc Base
Round
Tabletop
Rectangular
Tabletop
Square
Tabletop
OR
OR
OR
Racetrack
Tabletop
(Double all component parts for racetrack and rectangular tabletops.
Power
Module
Grommet

4 |www.sitonit.net |C6620 Rev A
Parallon MEETING/CAFÉ/OCCASIONAL TABLE ASSEMBLY INSTRUCTIONS
Step 1: Remove the plastic nut from the power module.
Plastic Nut
Note: If power module was not purchased, go to Step 4 on page 7.
Repeat all steps twice if installing the dual disc base table.

C6620 Rev A |www.sitonit.net |5
Parallon MEETING/CAFÉ/OCCASIONAL TABLE ASSEMBLY INSTRUCTIONS
Step 2: Insert the power module in through the top-side of the tabletop.

6 |www.sitonit.net |C6620 Rev A
Parallon MEETING/CAFÉ/OCCASIONAL TABLE ASSEMBLY INSTRUCTIONS
Step 3: Flip the tabletop over and tighten the plastic nut back onto the
power module.
Note: Place the tabletop on top of packaging to prevent damage to the
power module.

C6620 Rev A |www.sitonit.net |7
Parallon MEETING/CAFÉ/OCCASIONAL TABLE ASSEMBLY INSTRUCTIONS
Step 4: Slide the power cone onto the column.

8 |www.sitonit.net |C6620 Rev A
Parallon MEETING/CAFÉ/OCCASIONAL TABLE ASSEMBLY INSTRUCTIONS
Step 5: Attach the power cone to the column.
1:1 HARDWARE TOOLS
1⁄4"x 1⁄2" Bolt (Pack P)
3⁄8" Hex Socket, 1⁄4Drive
Hex Shank to Square Drive Adapter

C6620 Rev A |www.sitonit.net |9
Parallon MEETING/CAFÉ/OCCASIONAL TABLE ASSEMBLY INSTRUCTIONS
Step 6: Feed the power cord through the hole in the power cone and
route it through the opening at the bottom of the column.
Note: If power module was not purchased, skip this step.

10 |www.sitonit.net |C6620 Rev A
Parallon MEETING/CAFÉ/OCCASIONAL TABLE ASSEMBLY INSTRUCTIONS
Step 7: Attach the power cone to the underside of the tabletop.
1:1 HARDWARE
#12 x 1" Screw (Pack A) #3 Phillips Bit
TOOLS

C6620 Rev A |www.sitonit.net |11
Parallon MEETING/CAFÉ/OCCASIONAL TABLE ASSEMBLY INSTRUCTIONS
Step 8: Attach the disc base to the columns.
1:1 HARDWARE TOOLS
5⁄16 x 11⁄2" Bolt (Pack B)
1⁄2" Hex Socket, ¼" Drive
Hex Shank to Square Drive Adapter

12 |www.sitonit.net |C6620 Rev A
Parallon MEETING/CAFÉ/OCCASIONAL TABLE ASSEMBLY INSTRUCTIONS
Step 9: Turn the table upright with the help of another person and if
applicable, press the optional grommet into the cutout.
Note: Use packaging to prevent damage to the disc base when turning the
table upright.