SKYDANCE R9 User manual

Technical Parameters
Features
LVDRED
Input and Output
Operation temperature
Environment
Ta: -30
O
C ~ +55
O
C
Safety and EMC
EMC standard (EMC) ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Radio Equipment(RED) ETSI EN 300 328 V2.2.2
Certication CE,EMC,LVD,RED
EN 62368-1:2020+A11:2020
Safety standard(LVD)
Output signal (2.4 z)RF GH
Working voltage 3 AAAx2)VDC(
Working current <5mA
Standby current <10μA
Standby time 1 year
Remote distance 30m(Barrier-free space)
Warranty
5 years
Warranty
Gross weight
Size
Package
0.058kg
L114 x W65 x H20mm
Mechanical Structures and Installations
9mm
58.5mm
107mm
58.5mm
37.00 mm
63.00 mm
68.00 mm
C 2032 BatteryR
Back holder
To fix the remote, two options are offered for selection:
Option 1:
fix the remote' back holder on the wall with two screws.
Option 2:
adhere the remote' back holder to the wall with paster.
1
User Manual Ver 1.1.8
Model No.: R9
1 zone RGB or RGBW / 27 key / Wireless remote 30m distance / CR2032 battery
Ultrathin RGB/RGBW RF Remote Controller
● Apply to RGB or RGBW LED controller.
● Each remote can match one or more receiver.
● R bC 2032 attery powered.
● Operate with LED indicator light.
Note: If the LED indicator is not on when press key,
it is due to dead battery or bad contact caused by multiple plugging,
please replace the battery, or raise the battery shrapnel with a screwdriver.
Special
function key
"1"/Red,
"2"/Green,
"3"/Blue,
"4"/Yellow,
"5"/Purple,
"6"/Cyan
"7"/Orange
"8"/Grape
"9"/Grass green
"0"/Natural white
Mode+
Mode-
Speed- Bright-
On/Off
White
R/G/B+/-
Speed+ Bright+
Scene
Key function
Pull out the plastic battery barrier sheet from the battery compartment located on the bottom of the remote before key operation.
Mode+/-: Short press switch dynamic mode built in controller, long press 2s
Mode+ run mode cycle, long press 2s Mode- run the first mode.
The remote is default 10 dynamic mode, when match with SPI controller which
have 32 dynamic mode, please long press 2s Mode+ key firstly.
Speed+/-: Adjust dynamic mode speed,
short press 10 levels, long press 2s get the fastest / slowest speed.
Bright+/-: Adjust brightness,
short press 10 levels, long press 1-6s for continuous 256 levels adjustment.
R/G/B+/-: Adjust R/G/B brightness respectively, short press 10 levels,
long press 1-6s for continuous 256 levels adjustment to achieve millions of colors.
White: Adjust white color, for RGB light, short press turn on/off white(RGB mix),
long press 1-6s adjust saturation continuously.
For RGBW light, press W key will adjust W channel brightness.
short press turn on/off W channel,
long press 1-6s adjust W channel brightness continuously.
Scene: Short press recall the scene, long press 2s save the current color into the scene.
The LED indicator will light up longer when save OK.

1
User Manual Ver 1.1.8
● Set LED strip length [Pixel number(8~1024)]. * + 3 number + * for example:
*032* set pixel number to 32.
*600* set pixel number to 600.
*1024* set pixel number to 1024.
● Set LED strip chip type. * + 2 number + *
*11*：TM1803
*12*：TM1809, TM1804, TM1812, UCS1903, UCS1909, UCS1912, SK6813, UCS2903, UCS2909,
UCS2912, WS2811, WS2812, WS2813, WS2815
*13*：TM1829
*14*：TLS3001, TLS3002
*15*：GW6205
*16*：MBI6120
*17*：TM1814B(RGBW)
*18*：SK6812(RGBW), WS2813(RGBW), WS2814(RGBW)
*19*：UCS8904B(RGBW)
*21*：LPD6803, LPD1101, D705, UCS6909, UCS6912
*22*：LPD8803, LPD8806
*23*：WS2801, WS2803
*24*：P9813
*25*：SK9822
*31*：TM1914A
*32*：GS8206,GS8208
*33*： UCS2904
*34*： SM16804
*35*： SM16825
*36*： SM16714(RGBW)
*37*： UCS5603
*38*： UCS2603
● Set LED strip RGB order. * + 1 number + *
*1*：RGB, *2*：RBG, *3*：GRB, *4*：GBR, *5*：BRG, *6*：BGR.
Use R9 remote set SPI digital LED strip
Match Remote Control (two match ways)
Use the controller’s Match key
Match:
Short press match key, immediately press on/off key on the remote.
The LED indicator fast flash a few times means match is successful.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
End user can choose the suitable match/delete ways. Two options are offered for selection:
Delete:
Press and hold match key for 5s to delete all match,
The LED indicator fast flash a few times means all matched remotes
were deleted.
Safety information
1. Read all instructions carefully before you begin this installation.
2. When installing battery, pay attention to the battery positive and negative polarity.
A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the battery.
3. If no response from the receiver, please re-match the remote.
4. Gently handle remote, beware of falling.
5. For indoor and dry location use only.