Skymsen Fleetwood CT-300 User manual

Office
Phone: [phone]
Fax: [phone]
Warehouse
Phone: [phone]
Fax: [phone]
www.skyfood.us[email protected] -
TOLL FREE 1-800-503-7534
UG0111 - August /2011
Instructions Manual
Conveyor Toaster
Model
CT-300

SUMMARY
1-
2-
3-
4-
5-
Specifications
Transportation
Installation
Operation
Cleaning and maintenance
Trouble shooting6-
7- General safety practices
8- Electrical Diagram
1
1
1
2
3
3
4
6

01
Electric
×
1. Specifications:
2. Transportation:
During transportation, the machine should be taken care for the strong vibration.
The package cannot be put upside sown. It should be put inside the no corrosive gas
warehouse. If it is put in the open air, it should be covered with water-proof cloth.
3. Installation:
(1) The machine should be put on the flat place. And it should have more than 4 inches (10cm)
space with around flammables. In the front, it should have enough working space.
(2).You should have fixed power wiring near the working sit and wires should be
equipped with switch break down and electric leaking protection device. It must not have
any substance put around the switch.
(3).The power supply should be the same as the indication on the nameplate of the
machine. The power supply difference should not be over 10% of the rated voltage.
(4).The earth wire of the machine (yellow &green one)is together with the power
wire. It should be fixed to the qualified earth wire for safety.
(5).The wire terminals are in the back of the machine. You should connect with over
2
2.5mm cross sectional area copper wires.
(6).If the power wire is damaged, you should call your supplier or agent to replace it
for you.
(7).The installation should be done by the qualified electricians.
Characteristcs
Voltage
Frequancy
Fan Power
Motor Power
Heat Power
Power
Unit Size
Net Weight
Shipping Weight
Unit
V
Hz
W
W
W
KW
Inches
lb
lb
CT-300
110
60
30
80
190
1.94
14”19/32 x 16” 9/16 x 14” 31/32
62
73

02
4. Operation:
(1) The adjustment of the train net: Before shipment we have adjusted well
the train net. But after some times operation, you can adjust by yourself if necessary.
You can loose the bolt by the shaft and move the bearing base to adjust the train net.
(2) Turning on the power and press down the power switch”1”and the lamp is
on. Turning the thermostat switch”4”clockwise to the required temperature and the
heating lamp is on and the up and down heaters are heating and the toaster
temperature is increasing. When the temperature increases to the required
temperature, the thermostat will cut off the power automatically and the heating
lamp is off and the heaters stop working. When the temperature is down, the
thermostat turns on the power automatically, the heaters work again, In this
circulation, the temperature is kept in the setting range.
(3) Before bakery, heat the toaster for 12 min. first, then try to bake 2 pieces
of bread slices and adjust the temperature according to the toasting color of the bread
slices. If you need color dark, turn the thermostat switch wise to
over”2”position.After adjustment, put the bread slices on the train net and the bread
slices are shipped into the toaster for bakery.
(4) After bakery, the bread slices will be shipped to the bottom container and
will be shipped to the front via the bottom container. If you like to take them from the
back, you can press down the sliding trail to make it fixed to the pole by the train
wheel. The baked bread slices will be shipped into the back container. After
operation, you can put the sliding trail back.
(5) After operation, please turn counter clock wise the thermostat in the
original position and cut off the power.
WARNING: NEVER PUT THE FLAMMABLES ON THE TOASTER
WHEN WORKING!

03
5. Cleaning and maintenance:
(1).After operation everyday, draw out of the container and remove all of the
impurities. Clean the toaster surface and wires with wet towel and un-corrosive
divergent. But you cannot wash directly with water avoid damage of the electric
components.
(2).Never bake the candy coating or juice inside food to avoid it sticking on the
toaster.
6. Trouble shooting:
The above trouble shootings is only for your reference, if any troubles
happen, please stop operation and call for service.
Troubles
Causes Treatments
1.turn on the power and turn on
the thermostat,
but the
toaster is still cold
1.thermostat breaks down
2.heaters burnt out
1.replace the thermostat
2.replace the burnt heater
2.turn on the power and tune on
thermostat,
the toaster
temperature increase but
cannot be controlled
1.the thermostat breaks down
1.replace the thermostat
3.turn to the power,
the train net
cannot move
1.the motor breaks down
2.the train net is blocked
1.repair or replace the motor
2.check and remove the blocker
This product will be replaced or repaired under warrant y, for a period of (1) year,
beginning from the date of purchase by the original purchaser/user (“End User”), or
eighteen (18) months from the date of shipment from SKYFOOD’s warehouse,
whichever expires first.
Accessories will be replaced or repaired under warranty, for a period of (30) days,
beginning from the date of purcha se by th e original purchaser/user (“En d User”), or
eighteen (18) months from the date of shipment from SKYFOOD’s wa rehouse, whichever
expires first.
This warranty shall not take effect until a properly completed and executed WARRANTY
REGISTRATION form has been received by SKYFOOD EQUIPMENT, LLC, within thirty
(30) days from the da te of purch ase. The WARRANTY REGISTRATION is available either
in the Instruction Manual of every Product or at SKYFOOD’s website www.skyfood.us. The
End User must fill out the WARRANTY REGISTRATION form and send it to SKYFOOD
according to the instructions posted on the referred website. Failure to do so will VOID
the warranty.
No extended warranties for third party products. There are no other express
warranties or conditions other than the one offered by each manufacturer for
products sold by SKYFOOD, not under the FLEETWOOD by SKYMSEN and
SKYMSEN brand.
For questions or assistance, do not return the product or accessories to the store, please
call Toll Free 1-800-503-7534, or visit the Customer Service section at www.skyfood.us.
For faster service please have th e items name, serial number, and proof of purchase for
the operator to assist you.
SKYFOOD reserves the right to change the terms of its limited warranty at any time
without any prior notice. It also reserves the right to change the design and
specifications of its equipment or any related documentation at any time. The end
user is not entitled to upgrades or refunds resulting from these changes.
Updates
These Terms and Conditions were last updated on January 14th, 2014.

7-General Safety Practices
The following safety instructions are addressed to both the operator of the
machine as well as the person in charge of maintenance.
The machine has to be delivered to the operator in perfect conditions of use by
the Distributor to the user. The user shall operate the machine only after being well
acquainted with the safety procedures described in the present manual. READ THIS
MANUAL WITH ATTENTION.
Basic Operation Practices
Dangerous parts
Some parts of the electric devices are connected to high voltage points.
These parts when touched may cause severe electrical shocks or even be fatal.
Never touch commands such as buttons, switches and knobs with wet hands, wet
clothes and/or shoes. By not following these instructions operator could be exposed to
severe electrical shocks or even to a fatal situation.
Warnings
The operator has to be well familiar with the position of ON/OFF Switch to make
sure the Switch is easy to be reached when necessary. Before any kind of maintenance,
physically remove plug from the socket.
Provide space for a comfortable operation thus avoiding accidents.
Water or oil spilled on the floor will turn it slippery and dangerous. Make sure the floor is
clean and dry.
Before giving any manual command (switch, buttons, turn keys or lever) be sure
the command is the correct one. Check this manual for further details if necessary.
Never use a manual command (switch, buttons, lever) unadvisedly.
If any work is to be made by two or more persons, coordination signs will have to be given
for each operation step. Every step of the operation shall be taken only if the sign has
been made and responded.
Advices
In case of power shortage, immediately turn the machine OFF.
Use recommended or equivalent lubricants, oils or greases.
Avoid mechanical shocks as they may cause failures or malfunction.
Avoid penetration of water, dirt or dust into mechanical or electrical components
of the machine.
DO NOT modify original characteristics of the machine.
DO NOT remove, tear off or maculate any labels stuck on the machine. If any
label has been removed or is no longer legible, contact your nearest dealer for
replacement.
IMPORTANT
If any item from the GENERAL SAFETY NOTIONS section is not applicable to
your product, please disregard it.
04
SKYFOOD EQUIPMENT LLC - SERVICE
For questions o r assistance, call SKYFOOD EQUIPMENT Toll Free: 1-800-503-7534, or
visit the Customer Service section at www.skyfood.us.
SKYFOOD’S LIMITED WARRANTY
Unless otherwise specified,new FLEETWOOD by SKYMSEN and SKYMSEN products,
excluding accessories, sold by SKYFOOD EQUIPMENT, LLC. (“SKYFOOD”), for use only
in the continental United States (collectively, “Products” or singularly, “Product”), a re
warranted to be free from defects in materials an d workmanship for a period of one (1)
year from the date of purchase by the original purchaser/user (“End User”), or eighteen
(18) months from the date of shipment from SKYFOOD’s warehouse, whichever expires
first. Several new products and accessories may be warranted for a p eri od o ther tha n o ne
(1) year while others may be subject to travel limitations, as specified on the products
Instruction Manual. Proof of purchase must be presented; if not this warra nty will be
VOID. No warranty is given or imp lie d to a subsequent transferee or any other third party.
This warranty is expressly conditional upon SKYFOOD being notified of any defects in
materials or workmanship within five (5) days of its occurrence, within the warranted time
period. If a n otice of a claim under this warranty is timel y made by the End User,
SKYFOOD or a SKYFOOD’s designated service company (“Service Company”), will repair
or replace the Product, at SKYFOOD’s discretion, subject to the additional conditions
hereinafter described.
This warranty shall not apply if damage occurs from improper installation or maintenance
performed by an unauthorized service co mpany (“Service Company”), wrong voltage, nor
to the extent that Products or parts have been used other than in conformance with
operating and maintenance instructions, subjected to misuse or abuse or dama ged by
accident, acts of God, a bnormal use, stress or any other matter unrelate d to SKYFOOD,
and beyond its reasonable control. This warranty does NOT cover s ervice labor and
trave l to perform adjustments on products and/or accessories. In addition to wear and
tear of certain items, such as, but not limited to; glass parts, blades, stones, chopper
cutting knives, plates, slicing knives, cutting disc, gaskets, oil changes, sealing tape, heat
seal wires, worm gears, self-lubricating bushings, carbon brushes for electric motors, a nd
other parts expendable by nature and that need to be replaced frequently. Electrical
components are subject to natural wear and tear, and are NOT covered by this
warranty. THIS WARRANTY EXCLUDES ALL ORAL, STATUTORY, EXPRESS OR
IMPLIED WARRANTIES WHICH MAY BE APPLICABLE TO SKYFOOD, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR PURPOSE. Under no circumstances shall SKYFOOD be
liable for loss of use, re venue or profit or for incidental or consequential damages.
SKYFOOD shall under no circumstances be liable for any loss, damage, concealed
damage, expense or delay of goods for any reason when said goods are in th e custody,
possession or control of third parties selected by SKYFOOD to forward, enter, clear,
transport, or ren der other services with respect to such goods. The sole and exclusive
remedy for breach of any warranty is limited to the remedies provided in the paragraph
above.
All products held at non-comme rcial facilities or domiciles, mu st be taken or shipped,
shipping charges prepaid, either to SKYFOOD's facility or a SKYFOOD's designated
service company ("Service Company"). Products held at comme rcial facilities and weighing

SAFETY PROCEDURES AND NOTES BEFORE SWITCHING ON
IMPORTANT
Carefully read ALL INSTRUCTIONS of this manual before turning the machine ON.
Be sure to be familiar with the instructions and that you have well understood all
information contained in this manual. If you have any question contact your
supervisor or your nearest Dealer.
Danger
An electric cable or electric wire with damaged jacket or bad insulation could
cause electrical shocks as well as electrical leak. Before use, check conditions of all
wires and cables.
Advices
Be sure ALL INSTRUCTIONS in this manual have been thoroughly understood.
Every function and operational procedure have to be very clear to the operator.
Contact your nearest Dealer for further questions.
Any manual command (switch, button or lever) shall be given only after being
sure it is the correct one.
Precautions
The electric cable has to be compatible with the power required by the machine.
Cables touching the floor or close to the machine need to be protected against short
circuits.
AFTER THE WORK ENDS
Cares
Always clean the machine, to do the cleaning SWITCH IT OFF, AND TAKE
OUT THE PLUG FROM THE ELECTRICITY SUPPLY SOCKET .
Never clean the machine BEFORE IT IS COMPLETELY STOPED.
Fit all the machine components in their due places, before switching it on
again.
MAINTENANCE
Dangers
Any maintenance is dangerous if made with the machine switched on.
SWITCH IT OFF AND TAKE OUT THE PLUG FROM THE SOCKET, DURING
ALL THE MAINTENANCE OPERATION.
IMPORTANT
In any emergency situation, always take the plug out of its socket.
CEADVI S
e t c lrc a i mt n ebu ie es n .
El cri ao me h n cal ainena c shall e madeby q alif d p r o s
s nin camt n n e prel h c mwsThe per ohrgeofthe ain e a c eformanc s shal c e k the achine ork
OLF Y DTO .under T TASA ET CON I I NS
05 06
8- Electrical Diagram
K1:POWER SWITCH
K2:Equipment power switch
HI1:POWER INDICATOR
HL2:HEATING INDICATOR
M1:FAN
M2:MOTOR
KV1/KV2:VOLTAGE REGULATOR
R1/R2:HEATING ELEMENT