Sony WCS999 - Wireless Camcorder Microphone User manual

MICROFILM
SERVICE MANUAL
WIRELESS MICROPHONE SYSTEM
US Model
Canadian Model
SPECIFICATIONS
WCS-999
Transmitter
Receiver
Ver 1.0 1999. 09

– 2 –
TABLE OF CONTENTS
1. GENERAL ............................................................ 3
2. DISASSEMBLY ......................................................... 4
3. ELECTRICAL ADJUSTMENTS
TX Section ...................................................................... 6
RX Section ...................................................................... 8
4. DIAGRAMS
4-1. Block Diagram – TX Section – ..................................... 9
4-2. Block Diagram – RX Section – ..................................... 11
4-3. Printed Wiring Boards – TX Section –.......................... 13
4-4. Schematic Diagram – TX Section – ............................... 15
4-5. Printed Wiring Boards – RX Section – ......................... 17
4-6. Schematic Diagram – RX Section – .............................. 19
5. EXPLODED VIEWS................................................ 23
6. ELECTRICAL PARTS LIST ............................... 25
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.

– 3 –
SECTION 1
GENERAL This section is extracted from
instruction manual.

– 4 –
TX BOARD
ANTENNA SETTING
Note: Follow the disassembly procedure in the numerical order given.
SECTION 2
DISASSEMBLY
1 two screws
(P2 × 6)
4 TX board
3 case (upper)
2 two claws
3 case (lower
)
TX board
case (upper)
antenna
case (upper) rear view
cushion (lower), switc
h

– 5 –
RX BOARD
ANTENNA SETTING
3 case (upper)
2 two claws
3 case (lower)
1 two screws (P2 × 6)
4 RX board
antenna
case (upper
)
case (upper) rear view
RX board
cushion (lower), switch

– 6 –
0 dBm = 1 mW, 0 dBV = 1 Vrms
TX SECTION
1. Consumption Current Check
Setting:
Procedure:
1. Connect a regulated dc power supply (1.5V) and ampere meter.
2. Check that the value of ampere meter satisfy specified value.
Specified value: 70 mA to 80 mA
2.TX Frequency Confirmation
Setting:
Procedure:
1. Connect the 1/4 λsleeve antenna to a frequency counter, and
put the antenna by the lead wire antenna (ANT1).
2. Set the [RF CHANNEL] switch (SW51) to[1].
3. Confirm that the value of frequency counter satisfy specified
value.
4. Change the [RF CHANNEL] switch (SW51) to [2].
5. Confirm that the value of frequency counter satisfy specified
value.
6. Change the [RF CHANNEL] switch (SW51) to [3].
7. Confirm that the value of frequency counter satisfy specified
value.
Specified values: CH-1: 912.78 MHz to 912.92 MHz
CH-2: 913.68 MHz to 913.82 MHz
CH-3: 914.28 MHz to 914.42 MHz
Note: Tool
• 1/4 λsleeve antenna
Production procedure:
1. Cut about 80 mm of the outer cover at the other end of an
approximately 2 meter coaxial cable (1.5D-2V or the equiva-
lent) with a BNC connector.
2. Pull back the outer cover and fold the wire mesh over the out-
side cover.
3. Cover the folded back wire mesh (outer cover) with a tube (for
example, heat shrink tube) and fasten.
SECTION 3
ELECTRICAL ADJUSTMENTS
80 mm BNC
80 mm 80 mm BNC
BNC
The WCS-999 is a wireless microphone system operating in the 900
MHz. This system comprises the transmitter unit and the receiver unit.
+
–
regulated dc
power supply
mA Set
battery
terminal
#
battery
terminal 3
frequency counte
r
lead wire antenna (ANT1)
1/4
λ sleeve antenna
TX BASE
board

RX SECTION
1. Consumption Current Check
Setting:
Procedure:
1. Connect a regulated dc power supply (1.5V) and ampere meter.
2. Set the [RF CHANNEL] switch (SW1) to [1].
3. Check that the value of ampere meter satisfy specified value.
Specified value: 55 mA to 65 mA
2. RX Frequency Adjustment
Setting:
Procedure:
1. Connect the 1/4 λsleeve antenna to a SSG, and put the an-
tenna by the lead wire antenna (ANT2).
2. Connect a digital voltmeter to TP51 and TP102 on the RX
BASE board.
3. Connect REC out plug (P1) to an oscilloscope.
4. Set the [RF CHANNEL] switch (SW1) to [1].
5. Adjust CT3 on the RX BASE board so that the value of digi-
tal voltmeter becomes 1.4 V.
6. Confirm that the waveform of oscilloscope is sine wave.
7. Change the carrier frequency of SSG to 913.75 MHz.
8. Change the [RF CHANNEL] switch (SW1) to [2].
9. Adjust CT2 on the RX BASE board so that the value of digi-
tal voltmeter becomes 1.4 V.
10. Confirm that the waveform of oscilloscope is sine wave.
11. Change the carrier frequency of SSG to 914.35 MHz.
12. Change the [RF CHANNEL] switch (SW1) to [3].
13. Adjust CT1 on the RX BASE board so that the value of digi-
tal voltmeter becomes 1.4 V.
14. Confirm that the waveform of oscilloscope is sine wave.
– 7 – – 8 –
+
–
regulated dc
power supply
mA Set
battery
terminal
#
battery
terminal 3
3.TX Output Level Confirmation
Setting:
Procedure:
1. Connect the 1/4 λsleeve antenna to a spectrum analyzer, and
put the antenna by the lead wire antenna (ANT1).
2. Set the [RF CHANNEL] switch (SW51) to [1].
3. Confirm that the value of spectrum analyzer satisfy specified
value.
4. Change the [RF CHANNEL] switch (SW51) to [2].
5. Confirm that the value of spectrum analyzer satisfy specified
value.
6. Change the [RF CHANNEL] switch (SW51) to [3].
7. Confirm that the value of spectrum analyzer satisfy specified
value.
Specified values: CH-1: –10 dBm to –20 dBm
CH-2: –10 dBm to –20 dBm
CH-3: –10 dBm to –20 dBm
4. VCO Voltage Adjustment
Setting:
Procedure:
1. Connect a digital voltmeter to CP52 (the line of the TX BASE
board to the VCD board) and shield case (GND) of the VCO
board.
2. Set the [RF CHANNEL] switch (SW51) to [2].
3. Adjust CT1 on the VCO board so that the value of digital volt-
meter becomes 1.18 V.
4. Set the [RF CHANNEL] switch (SW51) to [1].
5. Confirm that the value of digital voltmeter satisfy specified
value.
6. Set the [RF CHANNEL] switch (SW51) to [3].
7. Confirm that the value of digital voltmeter satisfy specified
value.
Specified values: CH-2: 1.16V to 1.20 V
CH-1: 0.87 V to 0.89 V
CH-3: 1.37 V to 1.39 V
5.TX Modulation Sensitivity Adjustment
Setting:
Procedure:
1. Connect an AF OSC to the MIC jack (J1) on the TX BASE
board (transmitter unit).
2. Connect the REC out plug (receiver unit) to an audio analyzer.
3. Set the [RF CHANNEL] switch (SW51) to [1].
4. Adjust RV1 on the TX BASE board (transmitter unit) so that
the value of audio analyzer becomes –41 dBV.
5. Change the [RF CHANNEL] switch (SW51) to [2].
6. Adjust RV2 on the TX BASE board (transmitter unit) so that
the value of audio analyzer becomes –41 dBV.
7. Change the [RF CHANNEL] switch (SW51) to [3].
8. Adjust RV3 on the TX BASE board (transmitter unit) so that
the value of audio analyzer becomes –41 dBV.
Adjustment Location:
3. RX Output Level Adjustment
Setting:
Procedure:
1. Connect the 1/4 λsleeve antenna to a SSG, and put the an-
tenna by the lead wire antenna (ANT2).
2. Connect REC out plug (P1) to an audio analyzer.
3. Set the [RF CHANNEL] switch (SW1) to [2].
4. Adjust RV52 on the RX BASE board so that the value of au-
dio analyzer becomes –46.7 dBV.
Adjustment Location:
–TX BASE BOARD –
(Component Side)
MIC jack
(J1)
1
t 2 t 3
SW51
[RF CHANNEL]
RV3 CH-3
RV1 CH-1
RV2 CH-2
TX Modulation
Sensitivity Adjustment
RV51
TX Output Level
Adjustment
CT1
VCO Voltage
Adjustment
lead wire antenna (ANT1)
–VCO BOARD –
shield case CP52
audio
analyzer
AF OSC
Frequency: 1 kHz
Output level: –50 dBV
+
–MIC jack (J1)
TX BASE
board
receiver
unit
lead wire antenna (ANT1)
REC out plug
(P1)
spectrum analyze
r
more than 1 GHz
lead wire antenna (ANT1)
1/4
λ sleeve antenna
TX BASE
board
FM RF SSG
Carrier frequency: 912.85 MHz
Modulation: 1 kHz,
± 20 kHz deviation
Output level: – 60 dBm
REC out plug (P1)
RX BASE
board
lead wire
antenna (ANT1)
1/4
λ sleeve
antenna
+
–
digital voltmeter
to TP102 to TP51
oscilloscop
e
(DC range)
FM RF SSG
Carrier frequency: 913.75 MHz
Modulation: 1 kHz,
± 20 kHz deviation
Output level: – 60 dBm audio
analyzer
REC out plug (P1)
RX BASE
board
lead wire
antenna (ANT1)
1/4
λ sleeve
antenna
– RX BASE BOARD (Component Side) –
1 t 2 t 3 SW1
[RF CHANNEL]
CT3
CH-1CT2
CH-2 CT1
CH-3
RX Frequency
Adjustment
RV52
RX Output Level
Adjustment
lead wire antenna (ANT2)
+
–
digital voltmeter
Set
CP52
shield case
TP102
IC1
TP51
– RX BASE BOARD (Coductor Side) –

WCS-999
– 9 – – 10 –
SECTION 4
DIAGRAMS
4-1. BLOCK DIAGRAM –TX Section –
TRANSMITTER
IC51
DC/DC CONVERTER
IC101
05
•SIGNAL PATH
: TX
DC/DC CONVERTER
ON/OFF SWITCH
Q102
B+
OUT EXT
L101
D101
ANT1
LEAD
ANTENNA
PD
OUT
OSC1
IN
VCO BLOCK
OUT
XTALE
XTALB
X51
28.528MHz
X52
28.556MHz
X53
28.575MHz
D51
SW51-1
MIC
J1 RF
CHANNEL
SW51
CH-1
RV1
CH-2
RV2
CH-3
RV3
TX OUTPUT
LEVEL
RV51
VCO
VOLTAGE
CT1
TX MODULATION
SENSITIVITY
RV1 – 3
LOW-PASS
FILTER
OSC
Q101
OSC
BUFFER
IC52
FREQUENCY
DOUBLER
Q1
LINE
FILTER
LF101
RF AMP
Q2, 3
MULTIVIBRATOR
(FOR MUTING)
Q109, 110
REGULATOR
Q103
LED DRIVE
Q108
VOLTAGE
DETECT
IC102
DC/DC CONVERTER
CONTROL SWITCH
Q104, 105
SWITCHING
Q106
CRYSTAL
OSCILLATOR
PHASE
DETECTOR
OUTPUT
CIRCUIT
PWM
CONTROL
ERROR
AMP
VREF CHIP
ENABLE
f/N
MIC AMP
IC1 (1/2)
BUFFER
IC1 (2/2)
OSC4
1
23
7
8
9
4
1
SW51-2
D1 CT1 X1
1
2
3
POWER
SW101
BATT
D103
ON
OFF
DRY BATTERY
SIZE “AA”
(IEC DESIGNATION R6)
1PCS. 1.5V
CE
1,084MHz

WCS-999
– 11 – – 12 –
4-2. BLOCK DIAGRAM – RX Section –
FM FRONT-END, IF AMP, DET
IC1 (1/2)
POWER AMP
IC1 (2/2)
05
•SIGNAL PATH
: RX
B+
ANT2
LEAD
ANTENNA
RF
FRONT-END BLOCK
ANT
CT3
CT1
CF2
10.7MHz
CF1
10.7MHz
CT2
EXPANDER
D51
v
J51
RF
CHANNEL
SW1 RF
CHANNEL
D153
CH-3
CT1
CH-2
CT2
CH-1
CT3
RX OUTPUT
LEVEL
RV52
RX
FREQUENCY
CT1 – 3
BUFFER
IC52 (1/2)
BUFFER
IC51 (2/2)
BUFFER
Q152
SWITCHING
Q153
LED DRIVE
Q155
LINE AMP
IC52 (2/2)
LINE AMP
IC51 (1/2)
LINE
FILTER
LF101
EMI
FILTER
LF51
LOCAL OSC
Q3
LED DRIVE
Q101
TUNING
METER
FM IF
AMP
FM
DISCRIMI-
NATOR
FM
FRONT-END
AF POWER
AMP
DET,
AGC
RF AMP
Q1
MIXER
Q4
MIX
MIC
J52
X1
433.92MHz
1
2
3
POWER
SW101
BATT
D102
ON
OFF
DRY BATTERY
SIZE “AA”
(IEC DESIGNATION R6)
1PCS. 1.5V
SIGNAL METER
BUFFER
Q151
L1
(RF)
L2
(OSC)
REG (1.25V)
VREF
FM/AM
FE OUT
FM RF
IN
FM IF
IN
FM DISCRI
DET
OUT
MUTING
Q154
P1
(REC OUT)
VREF
VOL
AF
IN
AF
OUT
METER AFC/AGC AFC/AGC REG OUT AFC FM OSC FM RF
9 7 6 8 19 21 22
12 17
14
2
23
4
24 27
LIMITER
D151
D154
DC/DC CONVERTER
IC101
VOUT LX
OSC
OUTPUT
CIRCUIT
PWM
CONTROL
ERROR
AMP
VREF
23
L101
D101

WCS-999
4-4. SCHEMATIC DIAGRAM –TX Section – • See page 21 forWaveforms. •See page 22 for IC Block Diagrams.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ωand 1/4W or less unless otherwise
specified.
•C: panel designation.
•U: B+ Line.
•H: adjustment for repair.
• Powervoltage isdc 1.5 V and fedwith regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
• Voltages are taken with aVOM(Input impedance 10MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F:TX
– 15 – – 16 –

WCS-999
– 19 – – 20 – – 21 –
4-6. SCHEMATIC DIAGRAM – RX Section – • See page 22 for IC Block Diagrams.
3.9 Vp-p
10.2 µ s
– RX BASE Board –
1IC101 2(OUT)
2 V/DIV, 5 µs/DIV
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ωand 1/4W or less unless otherwise
specified.
•C: panel designation.
•U: B+ Line.
•H: adjustment for repair.
• Powervoltage isdc1.5V andfedwith regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : without the signal
( ) : receive the signal
• Voltages aretakenwith aVOM(Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J: RX
• Waveforms
–TX BASE Board –
1IC51 8(XTALE)
200 mV/DIV, 20 ns/DIV
2IC101 3(EXT)
2 V/DIV, 5 µs/DIV
580 mVp-p
CH-1 : 35.05 ns
CH-2 : 35.02 ns
CH-3 : 35.00 ns
3 Vp-p
10
µ s

GND
28
AF OUT
27
VCC AFC/AGC
26
RIPPLE FILTER
25
AF IN
24
DET OUT
23 22
AFC/AGC
21
IF GND
20
TUNING METER
19
NC
18
FM IF IN
17
AM IF IN
16
FM/AM BAND SELECT
15
MUTE
1
FM DISCRI
2
NF
FM OSC
3
VOL
4
AM OSC
5
AFC
6 7
REG OUT
8
FM RF
9
AM RF IN
10
NC
11
FM RF IN
12
FE GND
13
FM/AM FE OUT
14
TUNING
METER
FM IF
AMP
FM
DISCRIMI-
NATOR
FM
FRONT-END
AM
FRONT-END
AF
POWER AMP
AM IF AMP, DET,
AGC
• IC Block Diagrams
–TX BASE Board –
IC51 MC13176DR2
– 22 – – 23 – – 24 –
IC101 RH5RH303B-T1
IC101 XC6371A301PR
– RX BASE Board –
IC1 CXA1691AM-T6
OSC1 1
NC 2
NC 3
OSC4 4
VEE 5
ICONT 6
PD OUT 7
XTALE 8
IMOD
16
OUT GND
15
OUT2
14
OUT1
13
VCC
12
ENABLE
11
REG. GND
10
XTALB
9
CRYSTAL
OSCILLATOR
PHASE
DETECTOR
f/N
LX
SWITCH
CE 1
OUT 2
EXT 3
LX 4
VSS 5
OSC
BUFFER
PHASE
COMPARATOR
PWM
CONTROL
VLX
LIMITER
SLOW
START
CHIP
ENABLE
ERROR
AMP
VREF
+
–
LX
SWITCH
VSS 1
VOUT 2
LX 3
BUFFER
PHASE
COMPARATOR
PWM CONTROL
OSC
50/100/180kHz
VLX
LIMITER
SLOW
START
ERROR
AMP
VREF
+
–
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
(2) RX SECTION
(1) TX SECTION
SECTION 5
EXPLODED VIEWS
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Accessories and packing materials are given
in the last of the electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑↑
Parts Color Cabinet's Color
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 A-4540-594-A CASE (RX) SUB ASSY
52 2-544-527-11 KNOB (C)
53 2-544-526-11 KNOB (P)
*54 A-4541-195-A RX BASE BOARD, COMPLETE
55 2-545-828-01 TERMINAL (-), BATTERY
56 2-545-827-01 TERMINAL (+), BATTERY
57 2-544-532-01 CLIP (LOWER)
58 4-958-149-02 SPRING (CLIP)
59 2-544-531-01 CLIP (UPPER)
60 3-895-517-11 SCREW (2), TAPPING STEP
61 7-626-314-61 PIN, SPRING 2X5
62 7-685-104-19 SCREW +P 2X6 TYPE2 NON-SLIT
63 2-545-825-01 LID, BATTERY CASE
64 2-544-524-11 CASE (LOWER)
65 8-952-251-90 HEADPHONE MDR-E122 SET
66 4-963-644-11 CUSHION (LOWER), SWITCH
67 4-956-742-01 BUSHING CASE
P1 1-769-573-11 CORD, MICROPHONE (1 CORE) (REC OUT)
1 A-4540-593-A CASE (TX) SUB ASSY
2 2-544-527-11 KNOB (C)
3 2-544-526-11 KNOB (P)
*4 A-4541-194-A TX BASE BOARD, COMPLETE
5 2-545-828-01 TERMINAL (-), BATTERY
6 2-545-827-01 TERMINAL (+), BATTERY
7 2-544-532-01 CLIP (LOWER)
8 4-958-149-02 SPRING (CLIP)
9 2-544-531-01 CLIP (UPPER)
10 3-895-517-11 SCREW (2), TAPPING STEP
11 7-626-314-61 PIN, SPRING 2X5
12 7-685-104-19 SCREW +P 2X6 TYPE2 NON-SLIT
13 2-545-825-01 LID, BATTERY CASE
14 2-544-524-11 CASE (LOWER)
15 A-4540-587-A MICRROPHONE ASSY
16 4-963-644-11 CUSHION (LOWER), SWITCH
4
2
1
36
514
15
13
12
11
10
9
8
7
16
not
supplied
51
67
52
53
P1
65
64
63
55
56
54
62
61
60
59
58
57
66
not
supplied

– 25 –
SECTION 6
ELECTRICAL PARTS LIST FE RX BASE
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts speci-
fied in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when order-
ing these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. . uPA. . : µPA. .
uPB. . : µPB. . uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
When indicating parts by reference
number, please include the board.
FE BOARD
********
(Included in RX BASE board complete)
< CAPACITOR >
C1 1-162-906-11 CERAMIC CHIP 1.5PF 0.25PF 50V
C2 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C3 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C4 1-162-909-11 CERAMIC CHIP 4PF 0.25PF 50V
C5 1-162-918-11 CERAMIC CHIP 18PF 5% 50V
C6 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C8 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C9 1-162-920-11 CERAMIC CHIP 27PF 5% 50V
C10 1-113-713-91 CERAMIC CHIP 1PF 0.1PF 50V
C12 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C13 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V
C14 1-162-925-11 CERAMIC CHIP 68PF 5% 50V
C15 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C16 1-162-906-11 CERAMIC CHIP 1.5PF 0.25PF 50V
C17 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C20 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C21 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C23 1-162-906-11 CERAMIC CHIP 1.5PF 0.25PF 50V
C24 1-162-906-11 CERAMIC CHIP 1.5PF 0.25PF 50V
C28 1-162-917-11 CERAMIC CHIP 15PF 5% 50V
C29 1-162-924-11 CERAMIC CHIP 56PF 5% 50V
C30 1-162-921-11 CERAMIC CHIP 33PF 5% 50V
C39 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C40 1-162-909-11 CERAMIC CHIP 4PF 0.25PF 50V
C41 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C43 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C44 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C46 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C51 1-104-511-44 CERAMIC 0.001uF
C52 1-111-231-44 CERAMIC 2PF
C53 1-111-231-44 CERAMIC 2PF
< DIODE >
D1 8-719-988-61 DIODE 1SS355TE-17
< RESISTOR >
JC2 1-218-331-11 METAL CHIP 51K 5% 1/16W
< COIL >
L1 1-469-237-11 INDUCTOR CHIP 0.68uH
L2 1-469-237-11 INDUCTOR CHIP 0.68uH
L3 1-414-665-11 INDUCTOR CHIP 12nH
L4 1-414-665-11 INDUCTOR CHIP 12nH
L5 1-414-660-11 INDUCTOR CHIP 4.7nH
L6 1-414-660-11 INDUCTOR CHIP 4.7nH
< TRANSISTOR >
Q1 8-729-046-22 FET 3SK240 (TE85L)
Q3 8-729-043-92 TRANSISTOR 2SC5084-0 (TE85L)
Q4 8-729-232-73 TRANSISTOR 2SC4320 (TE85L)
< RESISTOR >
R1 1-216-845-11 METAL CHIP 100K 5% 1/16W
R2 1-218-331-11 RES, CHIP 51K 5% 1/16W
R4 1-216-853-11 METAL CHIP 470K 5% 1/16W
R5 1-216-845-11 METAL CHIP 100K 5% 1/16W
R7 1-218-269-11 RES, CHIP 360 5% 1/16W
R8 1-216-834-11 METAL CHIP 12K 5% 1/16W
R10 1-216-845-11 METAL CHIP 100K 5% 1/16W
R11 1-216-810-11 METAL CHIP 120 5% 1/16W
R12 1-216-809-11 METAL CHIP 100 5% 1/16W
R13 1-216-803-11 METAL CHIP 33 5% 1/16W
< VIBRATOR >
X1 1-767-906-11 RESONANTOR, SAW (433.92MHz)
**************************************************************
*A-4541-195-A RX BASE BOARD, COMPLETE
************************
(Including FE board complete)
< CAPACITOR >
C1 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C2 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C3 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C4 1-162-921-11 CERAMIC CHIP 33PF 5% 50V
C5 1-162-925-11 CERAMIC CHIP 68PF 5% 50V
C6 1-128-006-11 ELECT CHIP 4.7uF 20% 25V
C7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C8 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C9 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C10 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V

– 26 –
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C11 1-162-924-11 CERAMIC CHIP 56PF 5% 50V
C12 1-162-996-11 CERAMIC CHIP 7PF 0.5PF 50V
C13 1-107-686-11 TANTALUM CHIP 4.7uF 20% 16V
C14 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C15 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C16 1-104-851-11 TANTALUM CHIP 10uF 10% 10V
C17 1-162-912-11 CERAMIC CHIP 7PF 0.5PF 50V
C18 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C19 1-135-177-21 TANTALUM CHIP 1uF 10% 25V
C20 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C21 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C51 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C52 1-128-257-21 ELECT CHIP 33uF 20% 10V
C53 1-164-392-11 CERAMIC CHIP 390PF 5% 50V
C54 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C55 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V
C56 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C57 1-135-179-21 TANTALUM CHIP 2.2uF 10% 16V
C58 1-126-603-11 ELECT CHIP 4.7uF 20% 35V
C59 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C60 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C61 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V
C62 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C63 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C64 1-104-329-11 CERAMIC CHIP 0.1uF 10% 50V
C65 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C66 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C67 1-126-607-11 ELECT CHIP 47uF 20% 4V
C68 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C69 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C70 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C71 1-126-209-11 ELECT CHIP 100uF 20% 4V
C72 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C73 1-126-209-11 ELECT CHIP 100uF 20% 4V
C74 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C75 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C77 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C78 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C79 1-164-505-11 CERAMIC CHIP 2.2uF 16V
C80 1-115-156-11 CERAMIC CHIP 1uF 10V
C101 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C102 1-113-642-11 TANTALUM CHIP 47uF 20% 10V
C103 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C104 1-113-642-11 TANTALUM CHIP 47uF 20% 10V
C105 1-115-156-11 CERAMIC CHIP 1uF 10V
C151 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C152 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V
C153 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C154 1-126-607-11 ELECT CHIP 47uF 20% 4V
C155 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C156 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C158 1-115-156-11 CERAMIC CHIP 1uF 10V
< FILTER >
CF1 1-767-362-11 FILTER, CERAMIC
CF2 1-767-414-71 FILTER, CERAMIC
<TRIMMER>
CT1 1-141-327-11 CAP, CHIP TYPE TRIMMER 10PF
CT2 1-141-327-11 CAP, CHIP TYPE TRIMMER 10PF
CT3 1-141-327-11 CAP, CHIP TYPE TRIMMER 10PF
< DIODE >
D51 8-719-820-41 DIODE 1SS302
D101 8-719-076-79 DIODE ISS383-TE85L
D102 8-719-989-53 LED CL-200HR-C-TSL (BATT)
D151 8-719-054-23 DIODE RB706D-40-T146
D152 8-719-988-61 DIODE 1SS355TE-17
D153 8-719-062-48 LED CL-200YG-C-TS (RF CHANNEL)
D154 8-719-988-61 DIODE 1SS355TE-17
< IC >
IC1 8-752-092-18 IC CXA1691AM-T6
IC51 8-759-344-00 IC NJM2100E (TE2)
IC52 8-759-344-00 IC NJM2100E (TE2)
IC101 8-759-644-78 IC XC6371A301PR
< JACK >
J51 1-764-624-11 JACK (v)
J52 1-764-624-11 JACK (MIX MIC)
< RESISTOR >
JC152 1-216-864-11 METAL CHIP 0 5% 1/16W
< COIL >
L1 1-412-933-11 INDUCTOR 0.33uH
L2 1-419-331-21 COIL, CHIP 84nH
L51 1-414-671-21 INDUCTOR 0.1nH
L52 1-414-671-21 INDUCTOR 0.1nH
L53 1-414-671-21 INDUCTOR 0.1nH
L54 1-414-671-21 INDUCTOR 0.1nH
L101 1-419-334-21 COIL, CHIP 100uH
L151 1-412-034-11 COIL, CHIP 330uH
< FILTER >
LF51 1-411-236-11 FILTER, EMI
LF101 1-411-236-11 FILTER, EMI
< TRANSISTOR >
Q101 8-729-230-49 TRANSISTOR 2SC2712-YG
Q151 8-729-230-49 TRANSISTOR 2SC2712-YG
Q152 8-729-050-31 FET 2SK880-Y-TE85L
Q153 8-729-920-31 TRANSISTOR DTC343TK
Q154 8-729-015-39 TRANSISTOR DTC323TK
Q155 8-729-040-78 TRANSISTOR DTA124GKA-T146
< RESISTOR/THERMISTOR >
R1 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R2 1-216-815-11 METAL CHIP 330 5% 1/16W
R3 1-218-331-11 RES, CHIP 51K 5% 1/16W
R4 1-218-293-11 RES, CHIP 24K 5% 1/16W
R5 1-216-843-11 METAL CHIP 68K 5% 1/16W
R6 1-216-093-11 RES, CHIP 68K 5% 1/10W
RX BASE

– 27 –
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R7 1-216-812-11 METAL CHIP 180 5% 1/16W
R51 1-216-821-11 METAL CHIP 1K 5% 1/16W
R52 1-216-835-11 METAL CHIP 15K 5% 1/16W
R53 1-216-837-11 METAL CHIP 22K 5% 1/16W
R54 1-218-294-11 RES, CHIP 30K 5% 1/16W
R55 1-803-804-21 THERMISTOR, CHIP 15K
R56 1-216-834-11 METAL CHIP 12K 5% 1/16W
R57 1-216-833-11 RES, CHIP 10K 5% 1/16W
R58 1-216-847-11 METAL CHIP 150K 5% 1/16W
R59 1-216-833-11 RES, CHIP 10K 5% 1/16W
R62 1-216-837-11 METAL CHIP 22K 5% 1/16W
R65 1-220-158-11 RES, CHIP 3.6K 5% 1/16W
R66 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R67 1-216-833-11 RES, CHIP 10K 5% 1/16W
R68 1-218-707-11 RES, CHIP 4.3K 5% 1/16W
R69 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R70 1-216-836-11 METAL CHIP 18K 5% 1/16W
R71 1-216-833-11 RES, CHIP 10K 5% 1/16W
R72 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R73 1-216-821-11 METAL CHIP 1K 5% 1/16W
R74 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R75 1-216-821-11 METAL CHIP 1K 5% 1/16W
R76 1-216-815-11 METAL CHIP 330 5% 1/16W
R77 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R78 1-216-833-11 RES, CHIP 10K 5% 1/16W
R79 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R80 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R101 1-216-297-11 RES, CHIP 5.1 5% 1/10W
R102 1-216-826-11 METAL CHIP 2.7K 5% 1/16W
R103 1-216-849-11 METAL CHIP 220K 5% 1/16W
R104 1-218-332-11 RES, CHIP 130K 5% 1/16W
R151 1-218-273-11 RES, CHIP 510K 5% 1/16W
R152 1-216-821-11 METAL CHIP 1K 5% 1/16W
R153 1-216-837-11 METAL CHIP 15K 5% 1/16W
R154 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
R155 1-216-857-11 METAL CHIP 1M 5% 1/16W
R156 1-218-331-11 RES, CHIP 51K 5% 1/16W
R158 1-216-833-11 RES, CHIP 10K 5% 1/16W
R159 1-218-484-11 RES, CHIP 750 5% 1/16W
R161 1-216-845-11 METAL CHIP 100K 5% 1/16W
< VARIABLE RESISTOR >
RV51 1-223-586-11 RES, ADJ, CARBON 10K
RV52 1-223-586-11 RES, ADJ, CARBON 10K
< SWITCH >
SW1 1-692-034-11 SWITCH, SLIDE (RF CHANNEL)
SW101 1-572-018-11 SWITCH, SLIDE (POWER)
**************************************************************
*A-4541-194-A TX BASE BOARD, COMPLETE
***********************
(Including VCO board complete)
< CAPACITOR >
C1 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C2 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C3 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C4 1-164-346-11 CERAMIC CHIP 1uF 16V
C5 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C7 1-107-520-11 TANTALUM CHIP 33uF 20% 2.5V
C8 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C9 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C10 1-135-177-21 TANTALUM CHIP 1uF 10% 25V
C11 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C12 1-104-851-11 TANTALUM CHIP 10uF 20% 10V
C54 1-135-180-21 TANTALUM CHIP 3.3uF 20% 10V
C55 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C56 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C57 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C58 1-162-922-11 CERAMIC CHIP 39PF 5% 50V
C59 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C60 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C62 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C63 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C64 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C65 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C66 1-162-905-11 CERAMIC CHIP 1PF 0.25PF 50V
C67 1-135-177-21 TANTALUM CHIP 1uF 10% 25V
C69 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C70 1-162-909-11 CERAMIC CHIP 4PF 0.25PF 50V
C71 1-113-996-11 TANTALUM CHIP 220uF 20% 4V
C72 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C73 1-162-905-11 CERAMIC CHIP 1PF 0.25PF 50V
C101 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C102 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C103 1-107-520-11 TANTALUM CHIP 33uF 20% 2.5V
C104 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C105 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C106 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C107 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C108 1-111-253-11 TANTALUM CHIP 100uF 20% 6.3V
C109 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C110 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C111 1-111-253-11 TANTALUM CHIP 100uF 20% 6.3V
C112 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C113 1-135-177-21 TANTALUM CHIP 1uF 10% 25V
C114 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C115 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C116 1-164-160-11 CERAMIC CHIP 20PF 5% 50V
C117 1-164-160-11 CERAMIC CHIP 20PF 5% 50V
< DIODE >
D1 8-719-820-41 DIODE 1SS302
D51 8-719-041-39 DIODE KV1470
D101 8-719-076-81 DIODE SBS004CH3-TL
D102 8-719-056-74 DIODE UDZ-TE-17-3.0B
D103 8-719-989-53 LED CL-200HR-C-TSL (BATT)
< IC >
IC1 8-759-344-00 IC NJM2100E (TE2)
IC51 8-759-546-09 IC MC13176DR2
IC52 8-759-330-32 IC TC75S51F-TE85L
IC101 8-759-380-06 IC RH5RH303B-T1
IC102 8-759-572-21 IC S-80808ANNP-E7Y-T2
RX BASE TX BASE

– 28 –
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< JACK >
J1 1-764-624-11 JACK (MIC)
< RESISTOR >
JC1 1-216-295-00 SHORT 0
JC2 1-216-864-11 METAL CHIP 0 5% 1/16W
JC51 1-216-864-11 METAL CHIP 0 5% 1/16W
JC52 1-216-295-00 SHORT 0
JC53 1-216-295-00 SHORT 0
JC54 1-216-296-00 SHORT 0
< COIL >
L1 1-412-933-11 COIL, CHIP 0.33uH
L2 1-412-933-11 COIL, CHIP 0.33uH
L51 1-419-332-21 COIL, CHIP 1.8uH
L52 1-419-332-21 COIL, CHIP 1.8uH
L101 1-419-333-21 COIL, CHIP 68uH
< FILTER >
LF101 1-411-236-11 FILTER, EMI
< TRANSISTOR >
Q101 8-729-040-79 TRANSISTOR 2SD1628G-TD
Q102 8-729-230-49 TRANSISTOR 2SC2712-YG
Q103 8-729-046-89 TRANSISTOR 2SB970-S (TX).S0
Q104 8-729-230-72 TRANSISTOR 2SA1362YG
Q105 8-729-230-49 TRANSISTOR 2SC2712-YG
Q106 8-729-230-49 TRANSISTOR 2SC2712-YG
Q108 8-729-230-49 TRANSISTOR 2SC2712-YG
Q109 8-729-230-49 TRANSISTOR 2SC2712-YG
Q110 8-729-230-49 TRANSISTOR 2SC2712-YG
< RESISTOR >
R1 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R2 1-218-348-11 RES, CHIP 110K 5% 1/16W
R3 1-216-845-11 METAL CHIP 100K 5% 1/16W
R4 1-216-817-11 METAL CHIP 470 5% 1/16W
R5 1-216-821-11 METAL CHIP 1K 5% 1/16W
R6 1-218-344-11 RES, CHIP 7.5K 5% 1/16W
R7 1-216-847-11 METAL CHIP 150K 5% 1/16W
R8 1-216-835-11 METAL CHIP 15K 5% 1/16W
R9 1-216-839-11 METAL CHIP 33K 5% 1/16W
R51 1-216-845-11 METAL CHIP 100K 5% 1/16W
R52 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R53 1-216-845-11 METAL CHIP 100K 5% 1/16W
R54 1-216-845-11 METAL CHIP 100K 5% 1/16W
R55 1-216-853-11 METAL CHIP 470K 5% 1/16W
R56 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R57 1-216-838-11 METAL CHIP 27K 5% 1/16W
R58 1-216-821-11 METAL CHIP 1K 5% 1/16W
R59 1-202-926-11 RES, CHIP 36K 5% 1/16W
R60 1-216-811-11 METAL CHIP 150 5% 1/16W
R61 1-216-814-11 METAL CHIP 270 5% 1/16W
R62 1-216-817-11 METAL CHIP 470 5% 1/16W
R63 1-216-816-11 METAL CHIP 390 5% 1/16W
R101 1-216-809-11 METAL CHIP 100 5% 1/16W
R102 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R103 1-216-839-11 METAL CHIP 33K 5% 1/16W
R104 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R105 1-218-285-11 RES, CHIP 75 5% 1/16W
R106 1-216-849-11 METAL CHIP 220K 5% 1/16W
R107 1-216-833-11 RES, CHIP 10K 5% 1/16W
R108 1-216-845-11 METAL CHIP 100K 5% 1/16W
R109 1-218-350-11 RES, CHIP 3.9 10% 1/2W
R110 1-216-833-11 RES, CHIP 10K 5% 1/16W
R111 1-216-809-11 METAL CHIP 100 5% 1/16W
R112 1-216-849-11 METAL CHIP 220K 5% 1/16W
R113 1-216-853-11 METAL CHIP 470K 5% 1/16W
R114 1-216-853-11 METAL CHIP 470K 5% 1/16W
R115 1-218-332-11 RES, CHIP 130K 5% 1/16W
R116 1-216-849-11 METAL CHIP 220K 5% 1/16W
R117 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R118 1-216-837-11 METAL CHIP 22K 5% 1/16W
R119 1-216-837-11 METAL CHIP 22K 5% 1/16W
R120 1-216-851-11 METAL CHIP 330K 5% 1/16W
R121 1-216-851-11 METAL CHIP 330K 5% 1/16W
R122 1-216-837-11 METAL CHIP 22K 5% 1/16W
R123 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
< VARIABLE RESISTOR >
RV1 1-225-947-21 RES, CHIP ADJ 3K
RV2 1-225-947-21 RES, CHIP ADJ 3K
RV3 1-225-947-21 RES, CHIP ADJ 3K
RV51 1-225-946-21 RES, CHIP ADJ 200
< SWITCH >
SW51 1-692-034-11 SWITCH, SLIDE (RF CHANNEL)
SW101 1-572-018-11 SWITCH, SLIDE (POWER)
< VIBRATOR >
X51 1-781-623-11 OSCILLATOR, CRYSTAL (28.528MHz)
X52 1-781-624-11 OSCILLATOR, CRYSTAL (28.556MHz)
X53 1-781-625-11 OSCILLATOR, CRYSTAL (28.575MHz)
**************************************************************
VCO BOARD
**********
(Included in TX BASE board complete)
< CAPACITOR >
C1 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C2 1-162-906-11 CERAMIC CHIP 1.5PF 0.25PF 50V
C3 1-162-932-11 CERAMIC CHIP 2PF 0.25PF 50V
C4 1-162-904-11 CERAMIC CHIP 0.5PF 0.25PF 50V
C5 1-162-904-11 CERAMIC CHIP 0.5PF 0.25PF 50V
C6 1-162-904-11 CERAMIC CHIP 0.5PF 0.25PF 50V
C7 1-162-906-11 CERAMIC CHIP 1.5PF 0.25PF 50V
C8 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C9 1-162-911-11 CERAMIC CHIP 6PF 0.5PF 50V
C10 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V
C11 1-164-376-11 CERAMIC CHIP 11PF 5% 50V
C12 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
C13 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V
C15 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C16 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
TX BASE VCO

– 29 –
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C17 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C18 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C19 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C20 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C21 1-135-180-21 TANTALUM CHIP 3.3uF 20% 10V
C22 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C23 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C24 1-162-907-11 CERAMIC CHIP 2PF 0.25PF 50V
C51 1-125-825-11 CERAMIC 0.001uF 50V
C52 1-125-825-11 CERAMIC 0.001uF 50V
C53 1-125-824-11 CERAMIC 2PF 0.5PF 50V
< TRIMMER >
CT1 1-131-874-21 TRIMMER 3PF
< DIODE >
D1 8-713-101-23 DIODE 1T365-04-T8A
< COIL >
L1 1-419-329-21 COIL, CHIP 4.7nH
L2 1-419-330-21 COIL, CHIP 10nH
L3 1-419-328-21 COIL, CHIP 3.9nH
L4 1-419-330-21 COIL, CHIP 10nH
L5 1-419-330-21 COIL, CHIP 10nH
< TRANSISTOR >
Q1 8-729-043-92 TRANSISTOR 2SC5084-0 (TE85L)
Q2 8-729-043-92 TRANSISTOR 2SC5084-0 (TE85L)
Q3 8-729-043-92 TRANSISTOR 2SC5084-0 (TE85L)
< RESISTOR >
R1 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R2 1-216-819-11 METAL CHIP 680 5% 1/16W
R3 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R4 1-216-817-11 METAL CHIP 470 5% 1/16W
R5 1-216-841-11 METAL CHIP 47K 5% 1/16W
R6 1-216-837-11 METAL CHIP 22K 5% 1/16W
R7 1-216-837-11 METAL CHIP 22K 5% 1/16W
R8 1-216-839-11 METAL CHIP 33K 5% 1/16W
R9 1-216-809-11 METAL CHIP 100 5% 1/16W
R10 1-216-809-11 METAL CHIP 100 5% 1/16W
R11 1-216-801-11 METAL CHIP 22 5% 1/16W
< VIBRATOR >
X1 1-781-175-21 OSCILLATOR, DIELECTRICS (1,080MHz)
**************************************************************
MISCELLANEOUS
***************
P1 1-769-573-11 CORD, MICROPHONE (1 CORE) (REC OUT)
******************************************************************
ACCESSORIES & PACKING MATTERIALLS
**********************************
1-769-573-11 CORD, MICROPHONE (1 CORE) (REC OUT)
3-867-779-11 MANUAL, INSTRUCTION (ENGLISH, FRENCH)
(US, Canadian)
VCO
8-952-251-90 HEADPHONE MDR-E122 SET

– 30 –
WCS-999
Sony Corporation
Personal Audio Company
9-927-161-11 99I0519-1
Printed in Japan C1999. 9
Published by General Engineering Dept.