Soundoff Signal EFL1 User manual

FUSION LED LIGHT
#EFL1(x)Ø(x)
#EFL2(x)0(x)
EFL1B0(x)_EFL1W0(x) 1.15 Pg. 1
1.800.338.7337 / www.soundoffsignal.com
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage. To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at
www.soundoffsignal.com/sales-support. If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the
automated message). Questions or comments that do not require immediate attention may be emailed to [email protected].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
FIGURE 2
Please see last page for Technical Specifications !
WARNING
This product contains high intensity LED devices. To
prevent eye damage, DO NOT stare into the light
beam at close range.
INSTALLATION:
1. Establish a position on the vehicle on a level
surface. Orient the light output level on the
horizon.
2. Use the screw holes in the assembly as
a template to mark locations of wire and
mounting screws.
3. Use a 5/16” diameter drill for the wire holes
4. Size pilot holes for mounting screws
appropriately.
5. Fasten light using mounting
screws. Do not torque mounting screws
beyond 20 in - lbs.
FIGURE 1
WIRE HOOK-UP TABLE
WIRE COLOR: CONNECT TO:
RED +Vdc
BLACK Ground (-)
WHITE Pattern Select/Sync
GREEN Group Flash
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat
build-up and fire. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle
Owner’s Manual for deployment zones.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or fire.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
configuration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal
or local chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at
power source.
•Install protective grommets when routing wire through firewall or metal.
WARNING

FUSION LED LIGHT
#EFL1(x)Ø(x)
#EFL2(x)0(x)
EFL1B0(x)_EFL1W0(x) 1.15 Pg. 2
1.800.338.7337 / www.soundoffsignal.com
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage. To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at
www.soundoffsignal.com/sales-support. If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the
automated message). Questions or comments that do not require immediate attention may be emailed to [email protected].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
PATTERN SELECT
1. With light powered, touch White wire to Red Power wire for 1
second.
PATTERN RESET
1. With light powered, touch White wire to Red wire for 3
seconds.
2. Remove White wire from power. Pattern resets to 1.
SYNC MULTIPLE LIGHTS
1. Set up all lights to the same pattern
2. Connect White wires of all lights to sync together.
a. Note, only 6 lights can be synced together.
b. Insulate connections
3. Green Wire Connection
a. For Simultaneous Flashing of a group of lights:
i. Connect all Green wires together of the group of lights
desired to flash in unison.
ii. All Green wires connected together form one light group
b. For alternating flashing of a group of lights:
i. Connect one group of Green wires to Power (+Vdc)
ii. These lights will flash in unison.
iii. Connect one group of Green wires together but leave
floating.
iv. These lights will flash in unison.
v. Together, both light groups will alternate.
vi. For two lights simply connect one Green wire to Power
(+Vdc) and leave the other Green wire floating.
vii. Insulate connections.
Tech Specs Fusion Lite
Flash Patterns: 6 Flash Patterns
Light Sync: Yes
Technology: 1 Gen3 LED
Mounting: Surface Mount
Input Voltage: 10 - 30 Vdc
Current Draw: less than 0.1 amps
Dimensions:
Width x Height x Depth
3.125” (79.4 mm) W x 1.5” (38.5 mm)
H x .75” (19.5 mm) D
Operating Temp.: -20° to +65° C
Flash Patterns
Pattern Name
SAE
Pattern
ECE
Pattern 1 Light
F.P.M.
(Flashes / Minute)
1. Warp x x 353
2. Power Pulse x x 182
3. Road Runner x x 113
4. ECE Single x x 62
5. ECE Double x x 144
6. Quad x x 81