Soundoff Signal nFORCE LED Interior Lightbar User manual

nForce Interior Bar Rear Facing 13-19 Utility 1018
nFORCE LED Interior Lightbar
nForce Interior Lightbar Rear Facing 2013-2019 for the PI Ford Utility
NEXUS TECHNOLOGY
1.800.338.7337 / www.soundoffsignal.com
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com//tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. or after hours 5 p.m. to 8 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to [email protected].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
!
WARNING
This product contains high intensity LED devices.
To prevent eye damage, DO NOT stare into the
light beam at close range.
OPERATION:
SEE 'ELECTRICAL INSTALLATION' SECTION
OF THE NFORCE LED INTERIOR LIGHTBAR
INSTALLATION PACKET.
TRIM
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat
build-up and re. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle
Owner’s Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
conguration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal
or local chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at
power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING
1

nForce Interior Bar Rear Facing 13-19 Utility 1018
nFORCE LED Interior Lightbar
nForce Interior Lightbar Rear Facing 2013-2019 for the PI Ford Utility
NEXUS TECHNOLOGY
1.800.338.7337 / www.soundoffsignal.com
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com//tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. or after hours 5 p.m. to 8 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to [email protected].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
NOTES:
1. TOOLING TO BE BUILT FROM 3D DATA 0.010in
2. VOLUME = mm³
3. BREAK ALL SHARP EDGES, NO BURRS ALLOWED
4. GATE & EJECTOR LOCATIONS TO BE
APPROVED BY SOUNDOFF SIGNAL PRIOR
TO TOOL BUILD
REVISIONS
REV. DESCRIPTION BY DATE ECN
Utility I-sheets
MATERIAL:
NFORCE INT DURANGO 13+ SPLT FRT-UNICOR
THIRD ANGLE
PROJECTION
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE
PROPERTY OF SOUNDOFF SIGNAL. ANY REPRODUCTION IN PART
OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF
SOUNDOFF SIGNAL IS PROHIBITED.
®
XX
TEMPLATE
JMC
DRAWN
CHKD/APPR
DATE NAME
DESCRIPTION:
C:\Users\nbollo\Desktop\Utility I-sheets
SHEET
1 OF 1
4/12/2013
SIZE
DO NOT SCALE
DRAWING
TOLERANCES
EXCEPT AS NOTED
.X ± .020
.XX ± .012
.XXX ± .006
ANGLES ± .5°
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES
C
LONG
NOTES:
1. TOOLING TO BE BUILT FROM 3D DATA 0.010in
2. VOLUME = mm³
3. BREAK ALL SHARP EDGES, NO BURRS ALLOWED
4. GATE & EJECTOR LOCATIONS TO BE
APPROVED BY SOUNDOFF SIGNAL PRIOR
TO TOOL BUILD
REVISIONS
REV. DESCRIPTION BY DATE ECN
Utility I-sheets
MATERIAL:
NFORCE INT DURANGO 13+ SPLT FRT-UNICOR
THIRD ANGLE
PROJECTION
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE
PROPERTY OF SOUNDOFF SIGNAL. ANY REPRODUCTION IN PART
OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF
SOUNDOFF SIGNAL IS PROHIBITED.
®
XX
TEMPLATE
JMC
DRAWN
CHKD/APPR
DATE NAME
DESCRIPTION:
C:\Users\nbollo\Desktop\Utility I-sheets
SHEET
1 OF 1
4/12/2013
SIZE
DO NOT SCALE
DRAWING
TOLERANCES
EXCEPT AS NOTED
.X ± .020
.XX ± .012
.XXX ± .006
ANGLES ± .5°
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES
C
LONG
1.
REMOVE THE TOP REAR HATCH MOULDING
TO ACCESS THE SHEETMETAL STRUCTURE.
2.
2
DRIVER SIDE BRACKET
HATCHBACK SHOWN IN RAISED POSITION
PLACE BRACKET IN SHOWN LOCATION AND MARK HOLES
FOR DRILLING.
USING 2 SHEETMETAL SCREWS PROVIDED, ATTACH THE
BRACKET TO THE REAR HATCH
DRIVER
SIDE
REAR WINDOW

nForce Interior Bar Rear Facing 13-19 Utility 1018
nFORCE LED Interior Lightbar
nForce Interior Lightbar Rear Facing 2013-2019 for the PI Ford Utility
NEXUS TECHNOLOGY
1.800.338.7337 / www.soundoffsignal.com
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com//tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. or after hours 5 p.m. to 8 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to [email protected].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
NOTES:
1. TOOLING TO BE BUILT FROM 3D DATA 0.010in
2. VOLUME = mm³
3. BREAK ALL SHARP EDGES, NO BURRS ALLOWED
4. GATE & EJECTOR LOCATIONS TO BE
APPROVED BY SOUNDOFF SIGNAL PRIOR
TO TOOL BUILD
REVISIONS
REV. DESCRIPTION BY DATE ECN
Utility I-sheets
MATERIAL:
NFORCE INT DURANGO 13+ SPLT FRT-UNICOR
THIRD ANGLE
PROJECTION
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE
PROPERTY OF SOUNDOFF SIGNAL. ANY REPRODUCTION IN PART
OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF
SOUNDOFF SIGNAL IS PROHIBITED.
®
XX
TEMPLATE
JMC
DRAWN
CHKD/APPR
DATE NAME
DESCRIPTION:
C:\Users\nbollo\Desktop\Utility I-sheets
SHEET
1 OF 1
4/12/2013
SIZE
DO NOT SCALE
DRAWING
TOLERANCES
EXCEPT AS NOTED
.X ± .020
.XX ± .012
.XXX ± .006
ANGLES ± .5°
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES
C
LONG
PASSENGER
SIDE
HATCHBACK SHOWN IN RAISED POSITION
PLACE BRACKET IN SHOWN LOCATION AND MARK
HOLES FOR DRILLING.
USING 2 SHEETMETAL SCREWS PROVIDED, ATTACH
THE BRACKET TO THE REAR HATCH
3
REAR WINDOW
PASSENGER SIDE BRACKET
3.

1.800.338.7337 / www.soundoffsignal.com
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com//tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. or after hours 5 p.m. to 8 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to [email protected].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
nForce Interior Bar Rear Facing 13-19 Utility 1018
REINSTALL TOP REAR HATCH MOULDING.
ADJUST SHROUD SO IT IS LEVEL AND THE TRIM IS
TOUCHING THE REAR WINDOW.
TIGHTEN ALL SCREWS TO SECURE IN PLACE
ROUTE WIRES TO SWITCHING EQUIPMENT. BE MINDFUL
TO KEEP WIRE ROUTING AWAY FROM AIRBAG
DEPLOYMENT ZONES.
OPERATION:
SEE 'ELECTRICAL INSTALLATION' SECTION OF THE NFORCE LED
INTERIOR LIGHTBAR INSTALLATION PACKET.
4
REAR WINDOW
TRIM
MOUNTING
BRACKET
RUBBER SEAL
SECURE THE MOUNTING BRACKETS TO THE LIGHTBAR SHROUD
LOOSELY USING THE PROVIDED 1/4-20 PHILLIPS HEAD SCREWS