Soundoff Signal ETSS100NBKTH User manual

1.800.338.7337 / www.soundo󰀨signal.com
ETSS100NBKTH 0120
1
2017 CHEVROLET TAHOE SPEAKER BRACKET
ETSS100NBKTH (for 2017-2020 model years only)
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
INSTALLATION:
1. Front bumper cover assembly must be removed
to install speaker bracket. Assembly should
be removed as one piece and not individually.
Consult a local Chevrolet service center for best
disassembly method. Keep all hardware.
2. Assemble bracket:
- If using one speaker, choose location and
use support bracket. (See Figure 1.)
- If using two speakers, support bracket is
not used (See Figure 2.)
WARNING
!
Sirens produce loud sounds that
may damage hearing
Roll up windows
Wear hearing protection
Use only for emergency response
Avoid exposure to siren sound
outside of vehicle
I
I
I
I
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat build-up and re. Follow crimp connector
manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle Owner’s Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring conguration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal or local chassis ground (-) must be sized to
supply at least 125% of max. current and properly fused at power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING Please see next page for Technical Specications
FIG. 1 FIG. 2

ETSS100NBKTH 0120
2
2017 CHEVROLET TAHOE SPEAKER BRACKET
ETSS100NBKTH (for 2017-2020 model years only)
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
FIG. 3
1.800.338.7337 / www.soundo󰀨signal.com
INSTALLATION (cont.):
3. Remove the two bottom, middle louver screws (See
Figure 3.)
4. Hang bracket, seating screws so they are started.
Tighten screws at bottom then tighten screws at
top (See Figure 4.)
5. Wire speaker to siren output and test.
6. Re-install front bumper cover assembly using
previously removed hardware.
FIG. 4
TECHNICAL SPECIFICATIONS
Material: Steel with powder coated black
nish
Dimensions
(bracket only):
17.70”H x 11.92”W x 3.13”D
HARDWARE
QTY COMPONENT
1SPEAKER BRACKET, LH
1SPEAKER BRACKET, RH
1BRACKET, CAMERA INNER TUB
418-8 STAINLESS STEEL HEX
HEAD SCREW
418-8 STAINLESS STEEL
OVERSIZED WASH
4ZINC-PLATED STEEL SPLIT LOCK
WASHER
2FLATWASHER SS 1/4" (5/8" OD)
2M6 HEX HD 18-8 SS 30MM L