Soundoff Signal PNFSLFLKTTH User manual

TAHOE FOG LIGHT ASSEMBLY
PNFSLFLKTTH (for 2015-2020 model years)
1.800.338.7337 / www.soundo󰀨signal.com
Pg. 1 PNFSLFLKTTH 0120
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat
build-up and re. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle
Owner’s Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
conguration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal
or local chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at
power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING
TECHNICAL SPECIFICATIONS
Material: Plastic molded bezel, Black nish
Dimensions
(bracket only):
8.00”H x 11.00”W x 7.00”D
FRONT FOG LIGHT ASSEMBLY
-DRIVER/ PASSENGER-
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION

TAHOE FOG LIGHT ASSEMBLY
PNFSLFLKTTH (for 2015-2020 model years)
1.800.338.7337 / www.soundo󰀨signal.com
Pg. 2 PNFSLFLKTTH 0120
STEP 1
FOG LIGHT ASSEMBLY
-DRIVER SIDE SHOWN-
REAR VIEW OF FRONT BUMPER
-DRIVER SIDE-
4X SCREWS
- DO NOT DISCARD-
REMOVE FRONT BUMPER COVER ASSEMBLY AS ONE PIECE AND NOT INDIVIDUALLY.
CONSULT A LOCAL GM SERVICE CENTER FOR BEST DISASSEMBLY METHOD.
-KEEP ALL HARDWARE-
STEP 2
REMOVE THE 4 SCREWS THAT HOLD THE FACTORY
FOG LIGHT BEZEL AND PROCEED TO STEP 3 AND 4
FOR THE ASSEMBLY PROCEDURE.

TAHOE FOG LIGHT ASSEMBLY
PNFSLFLKTTH (for 2015-2020 model years)
1.800.338.7337 / www.soundo󰀨signal.com
Pg. 2 PNFSLFLKTTH 0120 Pg. 3 PNFSLFLKTTH 0120
STEP 3
FOG LIGHT BEZEL ASSEMBLY
-DRIVER SIDE SHOWN-
BEZEL
NFORCE LIGHT
MOUNTING PLATE
4X SCREWS,
4-40 X .25 LONG
2X SHEETMETAL SCREW
ASSEMBLE THE NFORCE LIGHT TO BEZEL AS
SHOWN BELOW. USE THE 4-40 SCREWS SUPPLIED
TO ATTACH PLATE TO LIGHT HOUSING IN 4 PLACES.
SCREW IN THE LIGHT HOUSING WITH PLATE TO THE
PLASTIC BEZEL WITH THE 2 SUPPLIED SHEETMETAL
SCREWS.
STEP 4
RE-ASSEMBLE THE BEZEL TO THE FRONT BUMPER IN REVERSE ORDER AND REUSE THE
EXISTING HARDWARE THAT WAS REMOVED ON STEP 2.
STEP 5
MAKE ALL ELECTRICAL CONNECTIONS. REFER TO THE INSTRUCTION
SHEET SUPPLIED WITH THE LIGHTS.