Soyal AR-327-E User manual

SOYAL
ACCESS CONTROL SYSTEM
®AR-327-E / 727-E V220816
- 1 -
CN4 CN5 CN7
CN6 CN3 CN2
AR-821RB
AR-821RB
CN4 CN5 CN7
CN6 CN3 CN8
1.Tubing: The communication wires and power line should NOT be bound in the same conduit or tubing.
2.Wire selection:Use AWG 22-24 Shielded Twist Pair to avoid star wiring ,CAT 5 cable for TCP/IP connection. Don’t equip reader and lock with the same power
supply. The power for reader may be unstable when the lock is activating, that may make the reader malfunction.
3.Power supply:The standard installation: Door relay and lock use the same power supply, and reader use independent power supply.
Attach the water proof strip to the mounting plate.
Pull the cables from the square hole of the mounting plate.
Use a screwdriver to screw the base onto the wall.
Connect the terminal cables to the body and attach the body to the mounting plate.
Assemble the covers with the Allen key and screws (accessories supplied).
Turn on the power, the LED will light and hear the beep sound, you will see "Ready""
on LCD board.
2User Guide 1Products 3Terminal Cables 4Tools 5Optional
AR-721RB
Digital Relay
Water proof Strip
2User Guide
1Products 3Terminal Cables 4Tools 5Optional
AR-721RB
Digital Relay
TCP/IP Module
and Cable
Water proof Strip
3
1
2
5
4
3
1
2
4
5
Contents
AR-327-E:Touch-panel Metal Case
AR-727- E
Installation
Notice
AR-327-E
Pull the cables from the square hole of the mounting plate.
Use a screw to the mounting plate onto the wall.
Attach the water proof strip to the body, then connect the terminal cables to the body
and attach the body to the mounting plate.
Use the Allen key and screws (accessories supplied) to assemble the body onto the
mounting plate.
Turn on the power, the LED will light and hear the beep sound, you will see "Ready""
on LCD board.
AR-727- E

V220816
- 2 -
6
5
4
3
2
1
CN11
6
5
4
3
2
1
CN9
8
7
6
5
4
3
2
1
CN5
CN3
8
7
6
5
4
3
2
1
CN4
2
1
CN6
7
6
5
4
3
2
1
CN7
4
3
2
1
CN8
7
7
6
6
5
5
4
4
3
3
2
2
1
1CN18
CN2
CN18
327-E
327-E
727-E
727-E
注意事項
AR-327-E AR-727-E
40 mm
140 mm
78.5 mm
92 mm
57 mm
91 mm 46 mm
126 mm
83 mm
LCD Access Controller
Wire Application Wire Color Description
1 --- ---
2 --- ---
TCP/IP Module
Output
3 Orange White
Net - TX+
4Orange Net - TX-
5Green White Net - RX+
6Green Net - RX-
7 --- ---
Wire Application Wire Color Description
RS-485 for Lift
Controller
1Thick Green RS-485(B-)
2Thick Blue RS-485(A+)
Wire Application Wire Color Description
Anti-Tamper
Switch
1Red N.C.
2Orange COM
3Yellow N.O.
Wire Application Wire Color Description
Power 1 Red DC 12V Output
Security trigger signal 2Purple Security trigger signal Output
Arming 3 Red White Arming Output
Duress 4 Yellow White Duress Output
(AR-327-E By order)
Wire Application Wire Color Description
Lock Relay 1Blue White (N.O.)DC24V1Amp
2 Purple White (N.C.)DC24V1Amp
Lock Relay COM 3White (COM)DC24V1Amp
Door Sensor 4Orange Negative Trigger Input
Exit Switch 5Purple Negative Trigger Input
Alarm Relay 6Gray N.O./N.C. Optional (by jumper)
Power 7Thick Red DC 12V
8Thick Black DC 0V
Wire Application Wire Color Description
Beeper 1Pink Beeper Output 5V/100mA, Low
LED 2Yellow Red LED Output 5V/20mA, Max
3Brown Green LED Output 5V/20mA, Max
Door Output 4Blue White Transistor Output Max. 12V/100mA
(Open Collector Active Low)
Wiegand 5Thin Green Wiegand DAT: 0 Input
6Thin Blue Wiegand DAT: 1 Input
WG Door Sensor
7Orange Negative Trigger Input
WG Exit Switch 8Purple Negative Trigger Input
(Optional)
(Optional) (Optional)
(Optional)
Main PCB
AR-727-E LCD-PCB
Connector Table
Cable: CN4
P1
Cable: CN6P4
P2Cable: CN5
P6Cable: CN8
P5Cable: CN3
Cable: CN7P3
INSTALLATION
Front View Front ViewSide view Side view

SOYAL
ACCESS CONTROL SYSTEM
®AR-327-E / 727-E V220816
- 3 -
AR-327-E AR-727-E
18/02 FRI Duty:0 18/02 FRI Duty:0
10:49:34 10:49:34
Ready...... Ready......
P
W
R
E
R
R
02 24
14 : 49 : 04
FRI
Duty : 0
1
2
3
4
5
6
7
8
E
12V
GND
12V
GND
12V
GND
N.O.
GND
N.O.
COM
PB
12V
GND
CN4
EXIT
7
6
5
4
3
2
1CN18
727-E
727-E LCD-PCB
7
6
5
4
3
2
1
327-E
CN18
EXIT
N.C.
COM
PB
12V
GND
N.O.
N.O.
COM
N.C.
V+
V-
7
6
5
4
3
2
1CN18
727-E
727-E LCD-PCB
7
6
5
4
3
2
1
327-E
CN18
CN4
1
2
3
4
5
6
7
8
12V
GND
12V
GND
12V
GND
N.O.
GND
N.O.
COM
PB
12V
GND
CN4
EXIT
7
6
5
4
3
2
1CN18
727-E
727-E LCD-PCB 7
6
5
4
3
2
1
327-E
CN18
ALM
12V
GND
12V
GND
12V
GND
12V
GND
N.C.
CN4
N.C.
N.O.
COM
CTL
12V
1
2
3
4
5
6
7
8
7
6
5
4
3
2
1CN18
727-E
727-E LCD-PCB 7
6
5
4
3
2
1
327-E
CN18
WG Port
WG Port WG Port
WG Port
WG Port
WG Port WG Port
WG Port
Main Port
Main Port Main Port
Main Port
P.T.Exit
Optional Cables
Front Panel & Indicator
Wire Application Wire Color Description
TTL Port for
Lift Control or Voice
Module
(*Required speaker
8Ω / 1.5W (Max.
2W)
1Black DC 0V
2Yellow TX
3White TE
4Orange RX
5Red DC 5V
6 --- ---
Wire Application Wire Color Description
HID ProxII RF
Module
1Orange ANT 1
2 Purple ANT 2
3Black DC 0V
4Red DC 5V
5Blue Wiegand DAT: 1 Input
6Green Wiegand DAT: 0 Input
7White --
Cable: AR-327-E: CN10 / AR-727-E: CN18 P8Cable: CN11(Optional:Lift Control w/ AR-725L485; SW:RS485-2) P7
CN9 (Optional:Voice Module; SW:RS485-3) P9
Data
Week
Work Status
Data [e.g.] 02/24←→02 24(Network Connected)
Week
Work Shift Status
Esc/Quit
Up
Down
Left
Right
Enter/OK
Power(Green)
Alarm(Red)
Arming (Green)
Esc/Quit
Up
Down
Left
Right
Enter/OK
OK(Green)
Error (Red)
In processing (Green)
Power(Green)
Alarm(Red)
Arming (Green)
OK(Green)
Error (Red)
In processing (Green)
Connect to Electric Bolt
Wiring Diagram
Controller
RTE
POWER
12VDC
POWER
12VDC
Controller
RTE
POWER
12VDC
POWER
12VDC
Magnet Lock
Connect to Magnet Lock
Connect to Electric Strike Connect to Door Sensor
Controller
POWER
12VDC
Electric Strike
Controller
POWER
12VDC Alarm
Electric Bolt
AR-1207
RTE
POWER
12VDC
POWER
12VDC
Relay Outpot Module
Door
Sensor
※The Wiring of Enable "Share Door Relay" ( Set up via the parameters setting Window of 701ServerSQL）
Door Sensor

V220816
- 4 -
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
E
12V
GND
12V
GND
12V
GND
12V
GND
PB
PB
COM
COM
N.O.
N.O.
CN4
CN4
12V
GND
12V
GND
PB
COM
N.C.
CN4
EXIT EXIT
7
6
5
4
3
2
1CN18
727-E
727-E
LCD-PCB
7
6
5
4
3
2
1
327-E
CN18
7
6
5
4
3
2
1CN18
727-E
727-E
LCD-PCB
7
6
5
4
3
2
1
327-E
CN18
7
6
5
4
3
2
1CN18
727-E
727-E
LCD-PCB
7
6
5
4
3
2
1
327-E
CN18
EXIT
WG Port WG Port WG Port
WG Port WG Port WG Port
Main Port Main Port Main Port
N.C.
N.O.
COM
CTL
12V
E
BZ
RLED
GLED
WG 1
12V
GND
1
2
3
6
12V
GND
12V
GND
CN5
CN4
BZ
RLED
GLED
Door Output
WG 0
WG 1
WG-DS
WG-PB
7
8
N.C.
EXIT
1
2
3
4
5
6
7
8
5
4
WG 0
7
6
5
4
3
2
1CN18
727-E
727-E
LCD-PCB
7
6
5
4
3
2
1
327-E
CN18
WG Port
WG Port
Main Port
P.T.Exit
EXIT
12V
GND
12V
GND
N.O.
12V
GND
CN4
N.C.
N.O.
COM
CTL
12V
GND
PB
AR-721RB
12V
GND
DDR
CN8
3
4
5
6
7
8
2
1
4
1 2 3
LCD Access Controller
If any re emergency, the people can escape by press a switch to open all doors
RTERTE
RTE
POWER
12VDC
POWER
12VDC
Electric Strike Electric Bolt
AR-1207
Fire Emergency
Transistor
IN4007
Transistor
IN4007
Transistor
IN4007
Magnet Lock POWER
12VDC
RTE
Controller
Controller
Reader
RTE
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
Door Contact
Strengthen security with AR-721RB
Electric Bolt
AR-1207
Electric Bolt
AR-1207
Connect to Reader
※ The Wiring of Disable "Share Door Relay" ( Set up via the parameters
setting Window of 701ServerSQL
※This wiring method is not eligible for "Share Door Relay" function (set up via
parameter setting of 701ServerSQL). If there is external wiring to Wiegand reader, WG
Port must enabled Digital Relay Output to enable "Share Door Relay" function.
AR-837-E/EE/EF/ER become WG mode
327-E/727-E WGoutput
12V
GND
CN4 CN4
CN8
CN5
CN5
BZ
RLED
GLED
Door Output
WG 0
WG 1
DS
PB
DS
PB
Duress
ALM
COM PB 12V GND 12V GND
1
2
3
4
5
6
7
8
1
2
3
4
1
2
3
4
5
6
7
8
1. When AR-327-E / AR-727-E become WG mode,it can be
used with any controllers.
POWER
12VDC
327-E/727-E Master
1
2
3
5
6
7
8
4
1
2
3
5
6
7
8
4
2. Standalone Setting: Enter programming mode -> 4. Parameters(2) ->
WG1 Port Share Main Relay -> select 1: YES
Networking Setting: Select E Series Controller Parameter Edit in 701Server,
tick up the function “Ev5 WG out/Hv3 Lift out”

SOYAL
ACCESS CONTROL SYSTEM
®AR-327-E / 727-E V220816
- 5 -
Access programming mode → Add/Delete → Add -> RF-Learn → Input 5/6-digit user address
→ Input Tag Units(pcs) → Close Tag into RF Area
※ If adding a batch of Sequential tags, please input Tag Units(pcs) in the quantity of the tags and present the
tag with the lowest card code to the access controller.
1 2
Adding Tag by RF Learn Function Tag Information
SITE CODE
CARD CODE
SITE CODE
CARD CODE
※ User capacity: 16384 (00000~16383)
Access programming mode → Add/Delete → Add -> Card ID → Input 5/6-digit user address → Input Site Code → Input Card Code
11
Adding Tag by Tag ID
Access programming mode → Add/Delete → Delete -> Addr → Input Starting address → Input Ending address
1 5
Deleting User Address
Access programming mode → User Setting → Access Mode → Input User Address → 0: Invalid; 1: Card ; 2: Card or PIN; 3: Card & PIN
2 2
Setting up the access mode
Access programming mode → Add/Delete → Delete -> ID # → Input Site Code → Input Card Code
1 6
Deleting Tag by Tag ID
F. PIN Code
C. Initial setup
E. Duress Code
Access programming mode → User Setting → Password → Input
5/6-digit user address → Input 4-digit PIN (0001~9999) → Succeeded Or via
701Client set it on Users screen
21
Node ID of Reader Setting
Access programming mode → Parameters[1] → Node
ID → Input New Node ID : 1~254 (default value:001) → Main
Door Number : 0~255 → WG1 Door Number : 0~255 →
Show WG Message (0=No,1=Enable) → Network setting
→ Succeeded
3 1
Language Setting
Access programming mode → Tools → Language →
0EN → Succeeded → Initial system...
5 1
H. Enable Voice Module (supporting version : F/w Ver 3.02
or later)
Software Setting 701 Server or
Programming
B. Entering and Exiting Programming Mode
Changing the Master Code
Access programming mode → Tools → Master Code →
Input the 6-digit new master code → Succeeded
5 2
A. Keyboard Lock/ Unlock
Lock/ Unlock
Press and , and at the same time to lock keyboard.
Press again to unlock.
Entering
Input 123456 or PPPPPP
[e.g.] The Default Value= 123456. If already changed the Master
Code= 876112, input 876112 → Access programming mode
P.S.If entering no instruction within 30 sec., it will automatically
leave the programming mode.
Exiting
Press the repeatedly → Quit or Quit and Arming
(Please refer to alarm / arming setting)
6 7
G. Setting up the alarm / arming
Conditions: 1. Arming enabled 2.Alarm system connected
Application:
1. Door open too long: Door is open longer than door relay time plus door close
time.
2. Force open (Opened without a valid user card): Access by force or illegal
procedure.
3. Door position abnormal: When power is o󰀨 and then on, reader on arming
before power o󰀨.
Step 1. Click "Read from Controller"
Step 2. Select "Card Reader / Voice Module" in RS485-2 section.
Step 3. Click "Write to Controller" to nish the setting.
Hardware setting
Access programming mode → Tools → Ext. Comm Port → Voice
552
Adding and Deleting Tag
1
2
3
Or via 701Server to set it on AR-829E-V5 screen
※Duress Code is only available in networking mode. It will
substitute a personal pin code and send the message of Duress
to computer as a warning signal.
※The Duress Code 0000 means that disable Duress Function and
the default value is set as 0000 already.
Access programming mode → Parameters[2] → Duress
Code → 4 sets (select one) → Input 4-digit PIN (0001~9999) →
Succeeded
4 7
D. PIN & UID Length setting
Access programming mode → Parameters[1] → PIN & UID
format → User PIN Length Range:4~8(4 is default value)
；
Card PIN Length Range:2~8(4 is default value)
39

V220816
- 6 -
RESET
LCD Access Controller
Enable/Disable the arming status:
Standby Mode
Access Programming mode
Card only Card or PIN Card and PIN
Open the door
Present the tag to reader → Input
4 digits arming PWD →
Input user address → Input 4
digits individual PWD → →
Input 4 digits arming PWD →
Present the tag to reader → Input
4 digits individual PWD → →
Input 4 digits arming PWD →
Enable: Access programming mode → Quit & Arming
7Disable: Access programming mode → Quit 6
No open the door
→ Input 4 digits arming PWD
→ Present the tag to reader
E. Setting up the alarm / arming
Restoring Factory Settings
Reset all device parameters and user card data
Reset IP Setting:
When the device's power is on, press the
【
RESET】 button the main board untill the ERR (Red) LED of
screen lights up. (Reference to picture)
※ After operation as above, you will hear the long reminder sound,and wait until the
sound disappear then reset the power of the controller,the device will restore factory setting.
Manu Tree
5. Tools
1. Language
2. Master Code
3. Master Range
4. Terminal Port
5. Ext.Comm Port
6. Open Time Zone
7. Informations
8. Clock Setting
9. Daily Alarm
0. UART Port
A. Event Logs
6. Quit
7. Quit & Arming
4. Parameters[2]
1. Auto Relock
2. Egress(R.T.E)
3. Miscellaneous
4. Force Open
5. Close & Stop
6. Anti-pass-back
7. Duress Code
8. Password Mode
9. Factory Reset
3. Parameters[1]
1. Node ID
2. OnO󰀨 OpenZone
3. Door Relay Tm
4. Door Close Tm
5. Alarm Relay Tm
6. Alarm Delay Tm
7. Arming Delay Tm
8. Arming PWD
9. PIN&UID format
2. User Setting
1. Password
2. Access Mode
3. Extend Options
4. Single Floor
5. Multi Floor
1. Add/ Delete
1. Add > Card ID
2. Add > RF Learn
3. Suspend > Address
4. Suspend > ID #
5. Delete > Address
6. Delete > ID #
7. Recover > Address
8. Recover > ID #
9. Antipass Group
Reset all device parameters and user card data:
Access programming mode → Parameters2 → Factory Reset →0 : System Param ;
1 : User Setting ; 2 : System & User
94
IP Setting
Log-in User Password
When you choose the "Networking Setting" or "User Password" at rst.
Log-in window will pop out and please input
※ At the Factory Default
User name: SuperAdm
Password: 721568
Open your Web Browser and input factory default IP
address: http://192.168.1.127
Networking Setting
You will nd initial IP Address 192.168.1.127 and check
MAC Address is the same as sticker on Ethernet Module
device. Please revise IP address you want, and then click
“Update” button. After updating the IP, please re-connect
the Web Browser by new IP address.
User Password
The password composes of 10 characters at most, it can be
either A~Z or 0~9.
Change the log-in password to lock the IP setting of
Ethernet Module.
If the IP address of AR-327-E
/ 727-E has changed We must
enter the new IP address.
※ The full screen menu setting is on page7 - Full Function Command Menu Table

V220816
- 7 -
LCD Access Controller
Entering
Input 123456 or PPPPPP
[e.g.] The Default Value= 123456. If already changed the Master Code= 876112, input 876112
→ Access programming mode
P.S.If no instruction is entered within 30 sec., it will automatically leave the programming mode.
Up
Down
Enter/OKEsc/Quit
1. Add/ Delete
2. User Setting
1-4. Suspend > ID #
2-4. Single Floor
1-9. Antipass Group
1-4-1
2-4-1
1-9-1
1-4-2
2-4-2
1-9-2
Set Site:
00000:XXXXX
Range: (0-65535)
User Address:
F3: Prev F4: Next
Range (0-016383)
Input Start Address
Range: (0-16383)
Set Code:
00000:XXXXX
Range: (0-65535)
Set Single Floor
(Range: 01~64)
Clear the Others
Input End Address
Range: (0-16383)
1-5. Delete > Address
2-5. Multi Floors
1-5-1
2-5 -1
1-5-2
2-5-2
Input Start Address
Range: (0-16383)
User Address:
F3: Prev F4: Next
Range: (0-016383)
Input End Address
Range: (0-16383)
Select Range:
1: 01-16 2: 17-32
3: 33-48 4: 49-64
1-3. Suspend -> Address
2-3. Extend Options
1-8. Recover > ID #
1-3-1
2-3-1
1-8-1
1-3-2
2-3-2
1-8-2
Input Start Address
Range: (0-16383)
User Address:
F3: Prev F4: Next
Range (0-16383)
Set Site:
00000:XXXXX
Range: (0-65535)
Input End Address
Range: (0-16383)
Is Guard User
0: NO 1: YES
Set Code:
00000:XXXXX
Range: (0-65535)
1-1. Add -> Card ID
2-1. Password
1-6. Delete > ID #
1-1-1
2-1-1
1- 6 -1
1-1-2
2-1-2
1-6-2
1-1-3
User Address:
00000 XXXXX
Range: (0-16383)
User Address:
F3: PreV F4: Next
Range (0-016383)
Set Site:
00000:XXXXX
Range: (0-65535)
Set (User Address) Code:
00000 XXXXX
(1-10 Digital)
Input PIN Code
Rang: 0000~9999
Set Code:
00000:XXXXX
Range: (0-65535)
Set (User Address) Code:
00000:_XXXX
Range: (0-65535)
1-2. Add -> RF-learn
2-2. Access Mode
1-7. Recover > Address
1-2-1
2-2-1
1-7-1
1-2-2
2-2-2
1-7-2
1-2-3
2-3-3 2-5-3
1-9-3
User Address:
F3: Prev F4: Next
Range: (0-016383)
User Address:
F3: Prev F4: Next
Range (0-163833)
Input Start Address
Range: (0-16383)
Tag Uints (Pcs)
Must be Sequence
Range: (1-016378)
0: Invalid 1: Card
2: Card or PIN
3: Card & Pin
Input End Address
Range: (0-16383)
Close Tag
Into RF Area
Enable Antipass
0: NO 1: YES
Data: 1
0->NO 1->YES
Current Setting:
1000000000000000
Enable Antipass
0: NO 1: YES
Data: 0
Full Function Command Menu Table

V220816
- 8 -
LCD Access Controller
Full Function Command Menu Table
3. Parameters [1]
4. Parameters [2]
3-3. Door Relay Tm
3-8. Arming PWD.
3-3-1
3-8-1
Main Door OpenTm
Range: 000~609
601~609=0.1~0.9
0077
Input PIN Code
Range: 0000~9999
1234
3-4. Door Close Tm
3-9. PIN&UID format
3-7. Arming Delay Tm3-5. Alarm Relay Tm 3-6. Alarm Delay Tm
3-4-1
3-9-1 3-9-3 3-9-5 3-9-7
3-7-13-5-1 3-6-1
Main Door Close
delay time (Sec)
Range: 000~255
015
User PIN Length
Range: 4~8
4
Show UID :0=No
1=WG 2=ABA
3=HEX 4=WG26
5=ABA8
1
RFID 125KHz RF
0: Disable
1: Enable
1
User Capacity:
0: 16384 1: 32768
2: 65536 (0~2)
0
Enter armed sta.
Delay time (Sec)
Range: 000~255
001
Alarm Relay Time
Range: 000~609
601~609=0.1~0.9
015
Alarm Output
Delay time (Sec)
Range: 000~255
3-2. OnOff OpenZone
3-2-1
Main Controller
Auto Open Zone
Dis/Enable (0/1)
0
3-1. Node ID
4-1. Auto Relock 4-2. Egress(R.T.E) 4-3. Miscellaneous
3-1-1
4-1-1 4-2-1 4-3-1 4-3-4 4-3-7
3-1-2
4-1-2 4-2-2 4-3-2 4-3-5 4-3-8
4-3-3 4-3-6 4-3-9
3-1-6 3-2-2
3-3-2 3-4-2
3-9-2 3-9-4 3-9-6 3-9-8
3-7-2
3-1-3 3-1-5 3-1-7
3-1-4 3-1-8
Input New NodeID
Range: 001~254
Current Data: 001
Main Controller
Auto Relock Door
0: NO 1:YES
0
Main Controller
Request TO Exit
0: Dis 1:Enable
0
Main Controller
TimeAttendance
0: YES 1: NO
0
WG1 Port
Skip PIN Check
0: NO 1: YES
0
WG1 Port
Share Main Relay
0: NO 1: YES
0
Main Door Number
Range: 000~255
WG Prot
Auto Relock Door
0: NO 1:YES
0
WG1 Port
Request TO Exit
0: Dis 1:Enable
0
WG1 Port
TimeAttendance
0: YES 1: NO
0
Main Controller
Pass any Tags
0: NO 1: YES
0
Tag Second time
interval (10ms)
Range: 0000~9999
0100
Main Controller
Skip PIN Check
0: NO 1: YES
0
WG1 Port
Pass any Tags
0: NO 1: YES
0
Max error times
for lock keypad
Range: (0~9)
5
IP Address (IPv4)
192.168.001.127
192.xxx.xxx.xxx
WG1 Port Auto Open
Zone Dis/Enable (0/1)
0
WG1 Door OpenTm
Range: 000~609
601~609=0.1~0.9
007
WG1 Door Close
delay time (Sec)
Range: 000~255
015
Card UID Length
Range: 2~8
4
NFC 13.56MHz RF
0: Disable
1: Enable
1
'#' is Door Bell
0: Disable
1: Enable
0
Enable Buzzer
0: NO 1: YES
1
Armed Pulse out-
put time. (10ms)
Range:000~255
000
WG1 Door Number
Range: 000~255
Net Mask (IPv4)
255.255.255.000
255.xxx.xxx.xxx
Show WG Message
0: NO 1:Enable
1
Gateway (IPv4)
192.168.001.254
192.xxx.xxx.xxx
Enable DHCP
0: No 1: En 2: Exit
192.168.001.127*
0
※User PIN Length Range:4~8(4 is default value)
；
Card PIN Length Range:2~8(4 is default value)

V220816
- 9 -
LCD Access Controller
Full Function Command Menu Table
4. Parameters [2]
5. Tools
6. Quit
※More Details：Introduction of New Function Commands for Enterprise E Controller and Home H Controller
7. Quit & Arming
4-3. Miscellaneous
5-1. Language
5-2. Master Code
5-3. Master Range
5-6. Open Time Zone 5-9. Daily Alarm 5-0. UART Port CN9
5-A. Event Logs
5-8. Clock Setting5-7. Informations
5-4. Terminal RS-485 5-5. Ext.Comm CN11
4-7. Duress Code 4-8. Password Mode 4-9. Factory Reset
4-4. Force Open .. 4-5. Close & Stop 4-6. Anti-passback
4-3-10
5-1-1
5-2-1
5-3-1
5-6-1 5-9-1 5-0 -15-8-15-7-1
5-4-1 5-5-1
4-7-1 4-8-1 4-9-1
4-4-1 4-5-1 4-6-14-3-12
4- 3-11
5-3-2
5-6-2 5-9-2 5-0-25-8-2
5-6-3 5-9-3
5-A-1
5-4-2 5-5-2
5-5-3
4-4-2 4-5-2 4-6-2
Main Controller
On Egress Beeps
0: NO 1: Bi 2: Bibb
2
0: English (USA)
1: Chinese (TW)
0
Input MasterCode
000001~999999
123456
Input Start Addr
Range: (0-16383)
000000
Set <F1~F4,#>: 01
00:00~00:00 ..
SuMoTuWeThFrSaHo
0 0 0 0 0 0 0 0
Set <F1~F4,#>: 01
00:00 Sec.=000
SuMoTuWeThFrSaHo
0 0 0 0 0 0 0 0
0: Lift9600 1: PRN
2: LED 3: Voice
0
YY: XXXX MM: XX
Day: XX Hour: XX
Min: XX Sec: XX
F/w Ver: 4.4T
Users: 00000
Messages: 00000
Press any Key ...
0: Lift 1: Host
2:LED 3: PRN
1
0: Suspend 1:Lift
2: Voice 3: PRN
1
Input PIN Code
Range: 0000~9999
Password Mode
0: Addr. & PIN(M4)
1: PIN(M8) 2:M6
1
0: System Param.
1: User Setting
2: System & User
2
Main Controller
Force Open Alarm
0: NO 1: YES
0
Main Controller
Close Door Stop
Alarm 0: NO 1:YES
0
Main Controller
Anti-passback
0: NO 1: YES
0
Lock Door Relay
0: NO 1: YES
0
WG1 Port
On Egress Beeps
0: NO 1: Bi 2: Bibb
2
Input End Addr
Range: (0-16383)
000000
Time=00:00~00:00
Nain Port (0/1):0
WG Port (0/1):0
Start Tm=00:00
Effect Sec.=000
Elevator oor
button available
Range: (1~600)
015
Month/Day Format
0: DD/MM 1: MM/
DD
Weekday: (0/1)
SuMoTuWeThFrSaHo
X X X X X X X X
0 0 0 0 0 0 0 0
Weekday: (0/1)
SuMoTuWeThFrSaHo
X X X X X X X X
0 0 0 0 0 0 0 0
20'06/04 2359:26
(M24)Controller
Power On 00000
Bud Selection
0: 9600 1: 19200
2: 38400 3: 57600
0: 4800 1: 9600
2: 19200 3: 38400
1
Elevator oor
button available
Range: (1~600)
000
WG1 Port
Force Open Alarm
0: NO 1: YES
0
WG1 Port
Close Door Stop
Alarm 0: NO 1:YES
0
WG1 Port
Anti-passback
0: NO 1: YES
0