SRC H-CB500X-07-01-SL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: H-CB500X-07-01-SL / H-CB500X-07-02
Part Description: GPS BAR –HONDA CB500X
Applicable to Finished colour versions of Black and Silver
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
Mounting Instructions
Step 1:
Removal of Windshield Guard Unscrew
the 4 mounting screws,(as shown) and
remove the Windshield Guard and keep
it aside. This will facilitate, access for
the mounting of SRC GPS Bar
Step 2:
Step 2: Unscrew the 4 mounting screws
(2 on each side) of the Windshield
Mounting Bracket, as shown.

Copyright By SRC
Design and Specification are subjected to change
Page 4
In the subsequent steps, we will
explain, as to how to move down the
Windshield Mounting bracket
Step 3:
Align the Top two mounting holes of the
Windshield bracket to the top two holes,
of the Inner bracket.
It is moving down, by One-pitch distance
of the Mounting holes in both the
Windshield bracket and the Inner
bracket

Copyright By SRC
Design and Specification are subjected to change
Page 5
Step 4:
Orient the Body of the Crash Bar (1),
its mounting holes aligned in-line with
the Windshield brackets (from both
sides) and slide-in the Washer M6 (5)
and Screw M6 x 10 (7) –2 off from
either side.
Secure the threads on the mounting
holes of the Inner bracket.
The GPS Bar (2), can be mounted to
the Body of the GPS Bar, using the
Adaptor (3) –2 off (1 from each side),
M8 Washer (4) and Screw M8 x 20 (6).
Mounting of the GPS Bar to the Body
of the GPS Bar, can be done off-line
too.
Step 5:
Tighten the Screws fully to the torque,
as specified in the BOM table

Copyright By SRC
Design and Specification are subjected to change
Page 6
Step 7:
The final mounted condition of the
GPS Bar is as shown.
Step 6:
The Windshield Guard, can be
mounted back in its original position

Copyright By SRC
Design and Specification are subjected to change
Page 7
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-by-
step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to the
Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part and
its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part. It
is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride and
at regular intervals.
7. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle or
the Part on which it is mounted to protect it
8. If any additional modifications are to be done, prior to the fitment of the accessories, it will be explicitly
specified in the instruction sheets