SRC H-NC750-02-01-SL Guide

Copyright By SRC
Design and Specification are subjected to change
Page 1
No. Description Quantity Torque * (N-m) Remarks **
1 Radiator Guard 1
2 Washer M6 1
3 Nut M6 1
4 Screw M6 1 9 - 10 Use Liquid Thread Locker
SRC Design uses Metric System of Measurement and all dimensions are in Millimeters
* Recommended to use the Torque specified in the table
** Denotes Usage of Liquid Thread Locker in specified locations
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: H-NC750-02-01-SL / H-NC750-02-02
Part Description: Radiator Guard –HONDA NC750X (2012-2020)
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
Mounting Instructions
Step 1:
Remove the Fastener in the top
side of the Radiator, as shown
and the one holding the bottom
clip.
The same screws has to be used
for mounting the Radiator
Guard, along with other
hardware as per the BOM.
Step 2:
Orient and Align the Radiator
Guard (1), as shown, and in-line
with the Top flap with the
mounting point, as shown in Red
colour, and Slip-in the
Hexagonal head bolt, which was
removed earlier and secure the
threads.
The Small Radiator Pin which
projects from the bottom side of
the Radiator, has to be passed
through the hole in the bottom
side of the Radiator Guard, as
shown.

Copyright By SRC
Design and Specification are subjected to change
Page 4
Step 3:
Insert the Screw M6 (4) –1 off,
Washer M6 (2) –1 off, through the
hole in the other side of flap and
through the mounting hole (as shown
in Red colour) and secure it using Nut
M6 (3) from the other side.
Ensure symmetry of Orientation and
no fouling with Outer or peripheral
surfaces of the Radiator and tighten
it fully.
Step 4:
Mount the Clip which was removed
in Step 1 and secure it using the
fastener back and align it to the
Radiator pin, as shown in the
drawing on the left-hand side.
The final mounted condition of the
Radiator Guard is as shown in the
drawing on the Right-hand side.

Copyright By SRC
Design and Specification are subjected to change
Page 5
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow
the step-by-step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the
Accessory part to the Vehicle. We have prepared this based on our experience and knowledge,
related to the Vehicle, Part and its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s
accessory part. It is advised to the User, to inspect and ensure the original state of all other
Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour
and/or the stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will
help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all
functions of the Vehicle. It is always advised to check loosening of the fasteners after the first
50 kilo meters of ride and at regular intervals.
7. We are showing here the Scope of Supply/ Installation/Parts list & BOM from SRC
8.To the maximum extent possible, our design use the current Mounting/Fitment of the
Original Equipment, so that Installation of these accessories will not affect the Payload or
Function of the Vehicle or the Part on which it is mounted to protect it
9.If any additional modifications are to be done, prior to the fitment of the accessories, it
will be explicitly specified in the instruction sheets.