SRC S-VS1050XT-09-01-AL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: S-VS1050XT-09-01-AL / S-VS1050XT-09-02-AL
Part Description: Engine Guard–SUZUKI V-STROM1050 XT
Applicable to Finished colour versions of Silver and Black
Installation / Parts List / Bill of Material for Mounting
=

Copyright By SRC
Design and Specification are subjected to change
Page 2
Mounting Instructions
Before installation,
remove the original Guard
and original crash bar (as
show)
As show RH motorbike
As show LH motorbike
Orient the Bracket RH (2)
and slip-in the Bush RH (7)-1
off, the washer M10 (13) –1
off, the long bolt M10x95
(12)-1 off,
Orient the Bracket Lower (4)
and slip-in the taper ring
(15) –1 off, the screw
M8x30 (10) –1 off,
And tighten it to torque as
shown in the BOM table.
As show RH motorbike

Copyright By SRC
Design and Specification are subjected to change
Page 3
Orient the Bracket LH (3)
and slip-in the Bush LH (6)-1
off, the washer M10 (13) –1
off, the long bolt M10x115
(11)-1 off,
Orient the Bracket Lower (4)
and slip-in the taper ring
(15) –1 off, the screw
M8x30 (10) –1 off,
And tighten it to torque as
shown in the BOM table.
As show LH motorbike
Orient the Engine Guard (1)
Bracket Front (5) at front
side in motorbike and slip-in
the Taper Ring M6 (14) –2
off, the screw M6x20 (9) –2
off,
Slip-in the Taper Ring M6
(14) –2 off, the screw
M6x15 (8) –2 off,
And slip-in the Taper Ring
M6 (14) –2 off, the screw
M6x15 (8) –2 off, at the end
side
And tighten it to torque as
shown in the BOM table.
As show RH motorbike

Copyright By SRC
Design and Specification are subjected to change
Page 4
Engine Guard in “As is
mounted condition” is as
shown in the drawing to the
Right.
As show RH motorbike

Copyright By SRC
Design and Specification are subjected to change
Page 5
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-by-
step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to the
Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part and
its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part. It
is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride and
at regular intervals.
7. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle or
the Part on which it is mounted to protect it
8. If any additional modifications are to be done, prior to the fitment of the accessories, it will be explicitly
specified in the instruction sheets