SRC H-CB500X-14-01-SL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
NO. Description Quantity Torque * (N-M) Remarks ** Check List
4
4 9 - 10
1
1
1
1
2
3
4
5 Bottom Plate
Top Plate
Middle Plate
Nut M6
SRCDesign uses MetricSystem of Measurement and all dimensions in Millimeters
*Recommended to use the Torque specified in the table
**Denotes Usage of Liquid Thread Locker in specified Locations
Countersink Screw M6 X 20
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: H-CB500X-14-01-SL
Part Description: Large Side Stand –Honda CB500 X
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
Mounting Instructions
The Motorbike has to be held using the central
stand, and Side Stand, drawn to the sides, to
have access to the mounting of Large Side
stand.
Side Stand looks as shown, prior to the Start of
the Installation of SRC Large Side Stand.
Step 1:
Orient and Slip-in the Middle Plate (3),
as shown.
The peripheral Inner walls of the
Middle plate, will closely hug the
outer walls of the Side stand.
Step 2:
Orient the Bottom Plate (5), in-line with
the Mounting Holes on the Middle Plate
and slide-in the M6 Screws from the
bottom side.
The Bottom plate has a rear side flap,
which closely hugs the Rear Periphery of
the Middle plate, to ensure orientation, as
well as to ensure No slackness.

Copyright By SRC
Design and Specification are subjected to change
Page 4
Step 3:
Slide-in the Top Plate (1), as shown
and orient the mounting holes in-line
with the 4 Projecting screws.
Step 4:
Secure the threads on the screw using
M6 Nut (5), as shown.
“As is Mounted condition “after Insertion of
the M6 Screws from the Bottom side, and
flushing the countersink contours of the
screws and the Bottom plate.

Copyright By SRC
Design and Specification are subjected to change
Page 5
Step 6:
Ensure all Mounting orientations
visually and ensure No slackness
between the Top, Middle and Bottom
plates, and tighten the Nuts to the
torque as specified in the BOM table.

Copyright By SRC
Design and Specification are subjected to change
Page 6
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-by-
step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to the
Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part and
its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part. It
is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride and
at regular intervals.
7. We are showing here the Scope of Supply/ Installation/Parts list & BOM from SRC
8. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle or
the Part on which it is mounted to protect it
9. If any additional modifications are to be done, prior to the fitment of the accessories, it will be explicitly
specified in the instruction sheets.