SRC H-X-ADV-21-01-01-SL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
Original Screw
Original Screw
NO. Description Quantity Torque * (N-M) Remarks **
1
1
10
6
6
2
2
4
1
1
6
1
2
3
4
5
6
7
8
9
10
11
Head Light Guard X-ADV 750 2021
Socket Button Head screw M5x10
Socket Button Head screw M5x25
5 - 6 Use LiquidThread Locker
5 - 6 Use LiquidThread Locker
Washer M5
Hex flange nut gradea M5
AD B Head Light Guard
AD Head Light Guard
SRCDesign uses MetricSystem of Measurement and all dimensions in Millimeters
*Recommended to use the Torque specified in the table
**Denotes Usage of Liquid Thread Locker in specified Locations
Rubber Grommet
Bush Delrin M5 14x13
Bush Delrin M5 8x11
Bush Rubber 5 mm
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: H-X-ADV-21-01-01-SL / H-X-ADV-21-01-02
Part Description: Head Light Guard –HONDA X-ADV 750 2021
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
Original Screw
Original Screw
Original Screw
Original Screw
Original Screw
Original Screw
Original Screw
Original Screw
2
2
2
2
2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
Original Screw
Original Screw
Original Screw
Original Screw
Original Screw
Original Screw
Original Screw
Original Screw
2
2
2
2
2
Mounting Instructions
Take off Original Screws, and Windshield.
Orient and align the AD Light Guard (3) as shown.
Slip-in the Spacer –Delrin M5 14x3(5) –2 off from
either side.
Slide-in the Washer M5 (4) and Screw M5 x 25 (10)
–2off, into the top side of the mounting hole, from
either sides.
Mounting of the Bottom Plate (11).This takes the
mounting hole available in the Motorbike (as
shown in the drawing).
Orient and align the Bottom Plate, and slide in,
Bush Delrin M5 8x11 (9) –2 off, and and Screw M5
x 25 (10) –2off, and Hex flange nut M5 (8)- 2 off,
from the Bottom side.

Copyright By SRC
Design and Specification are subjected to change
Page 4
Orient and Align the Head Light Guard (1), as shown,
Mounting holes in the Head Light Guard and Slide in
the Rubber Grommet (7) –4 off on each side.
Ensure Mounting symmetry and tighten the screws
to torque as per specifications in the BOM table.
Final Mounted condition of the Head Light Guard, is
as shown in the drawing above.

Copyright By SRC
Design and Specification are subjected to change
Page 5
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-by-
step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to the
Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part and
its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part. It
is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride and
at regular intervals.
7. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle or
the Part on which it is mounted to protect it
8. If any additional modifications are to be done, prior to the fitment of the accessories, it will be explicitly
specified in the instruction sheets