SRC BMW-F750GS-01-01-SL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: BMW-F750GS-01-01-SL / BMW-F750GS-01-02
Part Description: Head Light Guard –BMW F750 GS / F850 GS
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
The Mounting Screws, which will be used for
mounting the Brackets of the Head Light
Guard, can be found on the Front Left hand
side and Right hand side. The same can be
unscrewed out, 2 off on each side.
(Shown in the drawing is the view of it from
the Left Hand Side, when looking from the
front side of the Motorbike)
Mounting Instructions
Step 2:
Orient and align the Bracket LH (5) & Bracket RH (2), as shown. The cut-out in the bracket design,
clears the Head light.
Slip-in the Spacer –Aluminium (11) –1 off from either side, Spacer –Delrin (12) –1 off from either
side.
Slide-in the Washer M6 (6) and Screw M6 x 25 (8) –1 off, into the top side of the mounting
hole,
from either sides.
Slide-in the Washer M5 (7) and Screw M5 x 30 (9) –1 off, into the bottom side of the
mounting hole, from either sides.

Copyright By SRC
Design and Specification are subjected to change
Page 4
Step 3:
Secure the threads in the mounting
holes and ensure the orientation
symmetry and tighten them to torque,
as per specifications in the BOM table.
Step 4:
Slip-in the Mounting Pin (3) –2 off to each of
the Bracket RH and Bracket LH and secure it
using Screw M5 x 10 (10) –2 off and Washer M5
(7) –2off, as shown
(The same can be Assembled Off-line too)
Tighten it torque, as per specifications in the
BOM table.
Step 5:
Refer to the same drawing as above for
Mounting the Head Light Guard.
Orient the Head Light Guard (1), as
shown. Assemble the Grommet (4) –4 off,
hugging and flush, with the outer surfaces
of the Head Light Guard.

Copyright By SRC
Design and Specification are subjected to change
Page 5
Step 6:
Orient the Head Light Guard (1), in line with the Projections of the Mounting Pins and slide-
in the Grommet bore to the Shank of the Pins. The Shank of the pins, will hold by
Interference fit, the Rubber grommet, as shown.
The final mounted condition of the Head Light Guard is as shown above.

Copyright By SRC
Design and Specification are subjected to change
Page 6
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-by-
step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to the
Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part and
its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part. It
is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride and
at regular intervals.
7. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle or
the Part on which it is mounted to protect it
8. If any additional modifications are to be done, prior to the fitment of the accessories, it will be explicitly
specified in the instruction sheets