SRC KTM390-01-01-SL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
NO. Description Quantity Torque * (N-M) Remarks **
1
1
1
2
2
4
4
4
2
5 - 6
2
1
1
1
2
3
4
5
6
7
8
9
10
11
12
Head Light Guard
Use LiquidThread Locker
5 - 6 Use LiquidThread Locker
9 - 10 Use LiquidThread Locker
AD B Head Light Guard
AD F B Head Light Guard
AD Head Light Guard
Bush delrin M6 11x8
Socket but ton Head Screw M5x20 mm
Socket but ton Head Screw M5x10 mm
Socket but ton Head Screw M6x20 mm
Washer M5
Bush Rubber 5 mm
Rubber Grommet
Washer M6
SRCDesign uses MetricSystem of Measurement and all dimensions in Millimeters
*Recommended to use the Torque specified in the table
**Denotes Usage of LiquidThread Locker in specified Locations
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: KTM390-01-01-SL / KTM390-01-02
Part Description: Head Light Guard –KTM 390 Anventure
Applicable to Finished colour versions of Black and Silver
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
Mounting Instructions
Step 1:
Unscrew the Mounting Bolt, (original
Screw in the Motorbike) from the
Right Side, Left Side and Front Side.
Step 2:
Orient the Bracket (3), as shown, and
slip-in the Bush Rubber (10) and
Screw M5x10 (8) –2 off , and Screw
M5x20 (2) –1 off , as shown .
Step 3:
Orient the Bracket (5), and the
Bracket (12), as shown, and slip-in
the Bush Delrin (4)-2 off and Screw
M6x20 (7) –2 off , and Screw M5x10
(8) –2 off , and slip-in the Bush
Rubber (10) as shown .

Copyright By SRC
Design and Specification are subjected to change
Page 3
Step 4:
Orient the Head Light Guard (1), as
shown, and slip-in the Rubber
Grommet (11) –4 off and secure the
threads.
Step 5:
The Head Light Guard “As is final
Mounted Condition”

Copyright By SRC
Design and Specification are subjected to change
Page 4
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-by-
step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to the
Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part and
its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part. It
is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride and
at regular intervals.
7. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle or
the Part on which it is mounted to protect it
8. If any additional modifications are to be done, prior to the fitment of the accessories, it will be explicitly
specified in the instruction sheets