Steelcase Leap User manual

Page 1 of 6
939546224 Rev B
Leap®/Amia™/Think®Pivot Arm Cap Repair Kit
T20 & T25
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
© 2008 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
NEW SHOULDER SCREWS
(WITH PRE-APPLIED LOCTITE)
NEW PLASTIC FLAT WASHERS
NEW WAVE WASHERS
REPAIR KIT HARDWARE BAG
NEW SWING ARM LINK
NEW PIVOT PLATE
BEARING


1
Page 2 of 6
939546224 Rev B
2
1. Remove four (4) black screws
using a T20 drive bit as shown.
Keep all parts for reassembly.
2. Remove two (2) gold screws
using a T20 drive bit and remove
all parts as shown. Keep all parts
for reassembly.

OLD SHOULDER SCREWS
(WITHOUT LOCTITE)
3
4
5
Page 3 of 6
939546224 Rev B
OLD WAVE WASHERS
3. Remove the three (3) parts as
shown. Keep all parts for reassembly.
4. Remove two (2) shoulder bolts
using a T25 drive bit. Remove two (2)
wave washers as shown. These parts
will be replaced, so you can throw
these shoulder bolts and wave
washers away.
5. Remove swing arm link 'A' and
swing arm link 'B' as shown. These
parts will be replaced, so you can
throw these swing arm links away.
SWING ARM LINKS

7
NEW SWING ARM LINK
6b
NEW PIVOT PLATE
BEARING NEW SHOULDER SCREWS
(WITH LOCTITE)
8
Page 4 of 6
939546224 Rev B
NOTE: Torque shoulder
screws to 50 ±5 in/lbs.
using a T25 drive bit.
NEW PLASTIC
FLAT WASHERS
NEW WAVE WASHERS
6. Remove the OLD pivot plate
bearing (6a) and replace it with the
NEW pivot plate bearing (6b).
7. Place the NEW swing arm link 'A'
and swing arm link 'B' as shown.
8. Place the NEW plastic washers
into the counterbore holes. Place the
NEW wave washers on top of the
plastic washers. Take the NEW
shoulder bolts (with pre-applied
loctite) and install using a T25 drive
bit with a torque of 50 ±5 in/lbs.
6a
OLD PIVOT PLATE
BEARING

9
Page 5 of 6
939546224 Rev B
9. Snap the plastic cover back into
place as shown.
10. Place the plastic bearings back
into place as shown.
10

Page 6 of 6
939546224 Rev B
NOTE: Torque screws to
37 ±5 in/lbs. using a T20
drive bit.
11. Place the lower arm cap support in
place as shown (11a). Place the plastic
washer (flat side down), compression
spring and metal washer into place as
shown. Install gold screw using a T20
drive bit with a torque of 37 ±5 in/lbs (11b).
Place the plastic glider bracket as shown.
Install gold screw using a T20 drive bit
with a torque of 37 ±5 in/lbs (11c).

12. Place the foam arm cap in place as
shown and install with four (4) black
screws using a T20 drive bit as shown.
11b
11c
11a
12