Steelcase Huddleboard User manual

Huddleboard™Products
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2012 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
®
Page 1 of 4
939504755 Rev F
MARKERBOARDS
Hanger Hooks, Ledge Grabbers, Flip Chart Pegs, Marker Grip
PANEL/STRUCTURAL TRAY
MOBILE EASEL

Page 2 of 4
939504755 Rev F
®
MARKERBOARDS
Attaching Hanger Hooks
Necessary for hanging markerboards on
rails, Conjunction®, poster rack and
attaching ledge grabbers. Hooks can be
hung in horizontal or vertical orientation.
1. Remove boards and hanger hooks
from cartoning.
NOTE: Hanger hooks are found in the
same box with the boards, in the open
sleeve.
2. Push hanger hooks over edge of
board.
3. Slide hanger hooks over corner trim.
NOTE: Huddleboard
boards are not designed
to be ganged together.
Recommended Markers
EXPO®dry erase markers from
Sanford®.
Maintenance
Clean with warm soapy water,
wipe with sponge and allow to
air dry.
Attaching Ledge Grabbers
Slide the ledge grabbers over
top of hanger hooks.
Attaching Flip Chart Pegs
1. Push two pegs over edge of board.
2. Position pegs to fit holes in flip chart
pad.
3. Attach pad.
NOTE: Avoid stacking boards with flip
chart peg attached.
Attaching
Marker Grip to
Board
1. Slightly pinch
marker grip and
clip to edge of
board.
2. Push marker
into grip.

Page 3 of 4
939504755 Rev F
®
Tray Assembly and Installation
1. Align and mount brackets (A) to respective
panel or structural wall (drywall).
NOTE: For Architectural mountings, mount
brackets (A) 6” inboard to the end of tray location.
For all other panel systems, mount brackets at
desired height.
2. Slide end caps (B) on both ends of tray (C) and
fasten with screws.
3. Position assembled tray (C) on bracket (A) and
attach with screws.
NOTE: For 72” tray assemblies, 4 sets of brackets
are required to support tray.
Detail of locking tab for Avenir and Series 9000
bracket. Lock bracket into panel, position assembled
tray and attach with screws.
PANEL/STRUCTURAL (DRYWALL) TRAY
Avenir®,
Series 9000®
and
Answer®
Structural
(drywall)
brackets
B
C
A

Page 4 of 4
939504755 Rev F
®
MOBILE EASEL
Board Storage Capacity
2 boards can be displayed on sub-board
while the easel rack can store 10 more.
Mobile Easel Assembly
1. Remove easel (A) from box and press casters (B)
into base (C) (a rubber mallet may be necessary).
NOTE: If locking caster option is included, install
locking casters in the two front positions.
2. Remove tray (G) from sub-board (H).
3. Angle sub-board (H) to engage upper brackets (D)
and then rotate until vertical.
4. Align sub-board to lower brackets (D) through
rectangular window in sub-board (J).
5. Slide sub-board downward to fully engage to easel.
6. Assemble tray (G) with screws.
Large Boards
Can be mounted
horizontal and vertical.
Step 2
Step 1
Step 3
Step 4
Step 5
Step 6
A
C
B
G
I
H
D
D
H
J
D
G