Storage Canopy Two Car Garage Shelter User manual

SHELTER
ASSEMBLY MANUAL
Two Car Garage Shelter

Parst List
1
Roof bent tube
5
2
Incline tube
10
3
Shoulder bent tube
10
4
Standing leg
10
5
Purlin
20
6
Supporting tube for roof frame
5
7
Base Plate
4
8
Base Plate at middle
6
8A
Ratchet
10
9
Tension tube
2
10
Stake peg
20
11
Roof cover
1
12
Front and back cover
2
13
bolt 8*70mm
80
14
bolt 10*80mm
25
15
bolt 8*20mm
10
16
Rope
60 m
17
Nylon Band for Ratchet
10
18
Plastic cap
4
19
Supporting tube for arch frame
2
19A
Clip
4

SPECIFICATION
Width:22 Length: 24 Height: 11 ft
IMPORTANT ---- READ MANUALFIRST
Improper site preparation, Assembly and Maintenance may invalidate warranty and
cause unnecessary and costly mistake. If you have any questions contact your local
dealer.
For user friendly assembly we have identified each individual component with the part
code as indicated in the parts list. Please refer to the part code numbers and drawing to
ensure problem free assembly.
It’ s necessary to tighten the roof fabric enough to avoid “ hammocks” on the roof and
also re-tighten once or twice again after a few months of use. This is important when
assembly in cold weather (autumn and winter) because the fabric is stiff then and when
we got the sun and warm weather afterwards it will make the fabric “ slack”
again and need to be re-tighten before nextwinter.
It’ s the owners responsibility to take of snow immediately if not slide off by itself.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow
drifts, in slippery places, in high winds, or wet location.
2. Keep children away. All children should be kept away from the workarea.
3. Don’ t over reach. Keep proper footing and balance at all times.
4. Do not assemble in under the influence of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or reflexes are impaired while taking
drugs. If there is any doubt, do not assemble.
5. Be aware of possible windy conditions; fasten the bases in concrete if these
conditions are likely to occur. Remove the cover during hurricane.
6. Be careful with powerand heat sources. Do not keep heat sources near the tarpaulin.
Do not expose to open flame.
7. Be aware of personal safety during assembly and use. Be carful not to pinch fingers
with clips and tubes when assembling: when using makes sure there is adequate
ventilation for exhaust and other dangerous fumes.

EQUIPEMNT AND TOOLS FOR INSTALIATION
1. Measuring tape
2. String for alignment
3. Step ladder
4. Welder
5. Sledge hammer
6. Wrench
7. Scissors
INSTALLATION PROCESS
A—BASE INSTALLATION
Please refer to the diagram (Figure 1) to place the base plates. (UNIT: m)
Figure 1
1. The measure is from center to center of the tubes. Referring to the above diagram and confirm
the place of the base plates. ENSURE THAT THE FOUNDATIONS IS SQUARE.
2. There are two holes on the Base Plates, please using stake Pegs (No.10). THUS ALL BASE
PLATES ARE SECURED.
Note: The Stake Pegs apply for normal conditions, not suitable to the rock ground,
frozen soil and concrete ground.

、
、
、
Model: 222411P Frame Figure 2 (Size: W22 x L24 x H11 )

B--FRAME INSTALLATION
1. As Figure 3 shown find 1 piece of Roof Bent Tube (part code 1), 2 pieces of Incline Tube (part
code 2) 2 pieces of Shoulder Bent Tube (part code 3) and 2 pieces of Standing Leg Tube (Part No.
4). To connect them by using Bolt M8x70（part code 13）, which makes one group of peak arch.
Please NOTE the direction of the screw. DO NOT install the bolts on the top of the truss where the
fabric will rest.
Figure 3
2. Insert two end of the assembled peak arch into one base plate and force the other end of the peak
arch into the opposite base plate, fix them using Bolt M8x70mm（part code 13）.

Figure 4
3. After finishing installing the first two groups of peak arches, connect the Connection Tube (part
code 5) and Supporting tube for roof frame (Part No 6) onto them by using Bolt M10x80mm
（part code 14）. Then install the third group into base plate and connect the connection tubes,
there are 5 groups of peak arches and 5 pieces ofconnection tubes between each two groups. Finally
install the Diagonal Bracing Tube (part code 19) using Clip（part code 19A）asFigure No
2. By turns the assembly of the main frame is finished.
C--END DOORS ATTACHED
Figure 5
Door frame: Connect all the tube for door frame and fix them by using right bolts.
Put on the front and back covers (Part No. 12) refer to the Figure 5 and knit the cover by using
rope (No.16).
D- Install the Roof Cover

Figure 6
NOTE: DO NOT install the
cover onto the frame of your
building in high wind
conditions. A slight breezeis
the most advantageous for
cover installation. To take
advantage of the breeze,
pull the cover up over the
arches with the breeze
blowing in the cover like a
sail filled with air.
1. Put the Roof cover (part
code 11) EVENLY,
CARRFULLR AND
SLOWLY on the frame.
Adjust the cover so that it is square and evenly centered on the frame.
2. Use Rope (part code 21) to knit the cover on the two sides of the peak arches through all the
holes.
3. Cut 3 pockets according to the position of the base plates and insert the Lower Tension Tubes
(part code 9) into the pocket of roof cover. Then use the Ratchet (part code 8A) to fix the
Lower tension tubes like the Figure 7. Finally install the Plastic plug (part code 18) for into
two ends of the Lower tension tubes. Loosely secure the Nylon Band (No.17) in the ratchet on
the base plates. DO NOT TIGHTEN. Finally adjust the cover so that it is square and evenly
centered on the frame.
NOW THE INSTALLATION IS FINISHED, PLEASE ASJUST THE BASE PLATES VERY MONTH.

Figure 7
The process is
quite easy. But
some tightening
adjustments will
be necessary to
produce a flat,
tension roof
cover. Please adjust the roof cover every month or windy day.