Storage Canopy C604015S User manual

SHELTER ASSEMBLY MANUAL
Model # C604015S
W18x L12x H4.5m

C604015S Parts list
Part Code
Description
Qty
1
Top Bent Tube
6
2
Side Bent Tube on the top
12
3
Side Bent Tube on the bottom
12
4
Lower Bent Tube
12
5
Purlin
55
6
Top Steel wire
24
7
Clips
60
8LA
Left Base Plate
2
8L
Left Base Plate in the middle
4
8RB
Right Base Plate
2
8R
Right Base Plate in the middle
4
9
Ratchet
16
10
Nylon band for ratchet
12
11
Tensioning Tube
2 Groups
12
Bolts M12x40
204
12A
Tool
2
13
Bolts M10x80
66
14
Roof Cover
1
15
Knitting Rope for Cover
1
16
Plastic Plug
12
17
Base plates for roof cover
4
18
Inner standing leg
12
19LA
Left base plates for left standing leg
2
19L
Middle base plates for left standing leg
4
19RA
Right base plates for right standing leg
2
19R
Middle base plates for right standing leg
4
20
Bolts M8x80
24
24
PVC tube
2 Groups
25
Angle iron for base plate
12

SPECIFICATION
Length: 18m Width: 12m Height: 4.5m
IMPORTANT -----READ MANUAL FIRST
Improper site preparation, Assembly and Maintenance may invalidate warranty and cause
unnecessary and costly mistake. If you have any questions contact your local dealer.
For User Friendly assembly we have identified each individual component with the part code as
indicated in the parts list. Please refer to the part code numbers and drawing to ensure problem free
assembly.
It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also re-tighten
once or twice again after a few months of use. This is important when assembly in cold weather
(autumn and winter) because the fabric is stiff then and when we got the sun and warm weather
afterwards it will make the fabric “slack” again and need to be re-tighten before next winter.
It’s the owners responsibility to take of snow immediately if not slide off by itself.
READ ALL INSTRUCTIONS BEFOREASSEMBLY
1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in slippery
places, in high winds, or wet location.
2. Keep children away. All children should be kept away from the work area.
3. Don’t over reach. Keep proper footing and balance at all times.
4. Do not assemble in under the influence of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there
is any doubt, do not assemble.
5. Be aware of possible windy conditions; fasten the bases in concrete if these conditions are likely
to occur. Remove the cover during hurricane.
6. Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not
expose to open flame.
7. Be aware of personal safety during assembly and use. Be careful not to pinch fingers with clips
and tubes when assembling: when using makes sure there is adequate ventilation for exhaust
and other dangerous fumes.

EQUIPEMNT AND TOOLS FOR INSTALIATION
1. Measuring tape
2. String for alignment
3. Step ladder
4. Welder
5. Sledge hammer
6. Wrench
7. Scissors
INSTALLATION PROCESS
A—BASE INSTALLATION
Please refer to the diagram (Figure 1) to place the base plates. UNIT: mm
Figure 1
1. The measure if from center to center of the tubes. Referring to the above diagram and confirm the
place of the base plates. ENSURE THAT THE FOUNDATIONS IS SQUARE.
2. All the base plates need to use welder to be welded on the Containers.

Figure 2: Size: L18 x W12 x H4.5m
B—FRAME INSTALLATION

Figure 3
Figure 4

Figure 5
D—INSTRUCTION THE ROOF COVER
Figure 6

Figure 7

NOT install the cover onto the frame of your building in high wind conditions. A slight breeze is the most
advantageous for cover installation. To take advantage of the breeze, pull the cover up over the arches with
the breeze blowing in the cover like a sail filled with air.
NOTE: DO NOT LEAVE THE ROOF COVER UNATTACHED UNDER ANY CIRCUMSTANCES until the
final assembly and tightening has been completed. The process is quite easy. But some tightening adjustments will
be necessary to produce a flat, tension ed roof cover. Please adjust the roof cover every month.