Storage Canopy 26x40x10 Container Shelter Single truss User manual

1
SHELTER ASSEMBLY
MANUAL
26x40x10 Container Shelter Single truss

2
PARTS LIST
Part Code
Description
Qty
L1
Base plate with tie down ratchet on left side
7
R1
Base plate with tie down ratchet on right side
7
1
Top bent tube
7
2
Middle bent tube
14
3
Sidewall bent tube
14
4
Connection purlin
30
5
Support tube
12
6
Clip
24
7
Lower tensioning tube for roof cover
2 Groups
8
Roof cover
1
9
Bolt M8x70
88
10
Bolt M10x80
35
11
Ropes
1 dozen
12
∮32 Plastic plug for base rail section
4
13
Ratchet strap (To tie down ratchet)
14
14
Ratchet
14
15
Angle seat
4

3
SPECIFICATIONS
Width: 26 ft
Length: 40 ft
Height: 10 ft
IMPORTANT: READ MANUAL FIRST
Improper site preparation, assembly and maintenance may invalidate warranty and cause
unnecessary and costly mistakes. If you have any questions, contact your local dealer.
For an easy assembly process, we have identified each individual component with the part
code as indicated in the parts list. Please refer to the part code numbers and drawing to
ensure problem-free assembly.
It is necessary to tighten the roof fabric enough to avoid “hammocks” on the roof; also re-
tighten once or twice again after a few months of use. This is important when assembled
during cold seasons (autumn and winter) because the fabric gets stiff in these weather
conditions. When the weather conditions become warmer, the fabric loosens and needs
to be re-tighten
It is the owner’s responsibility to take off snow immediately, otherwise it will slide off on
its own.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
1. Keep the work area clean. Accidents are more likely in cluttered areas. Do not set
up near snow drifts, in slippery places, in high winds, or wet locations.
2. All children should be kept away from the work area.
3. Don’t overreach. Always keep proper footing and balance.
4. Do not assemble under the influence of alcohol or drugs. Read warning labels on
medication prescriptions to determine if your judgment or reflexes are impaired
while taking them. If there is any doubt, do not assemble.
5. Be aware of possible windy conditions; fasten the bases in concrete if these
conditions are likely to occur. Remove the cover during hurricanes.
6. Be careful with power and heat sources. Do not keep heat sources near the
tarpaulin. Do not expose to open flame.
7. Be aware of personal safety during assembly and use. Be careful not to pinch your
fingers with clips and tubes when assembling: When using, make sure there is
adequate ventilation for any dangerous fumes.

4
EQUIPMENT AND TOOLS FOR INSTALLATION
1. Measuring tape
2. Alignment string
3. Step ladder
4. Welder
5. Sledgehammer
6. Wrench
7. Scissors
INSTALLATION PROCESS
A - BASE PLATES INSTALLATION
Please refer to the Figure 1 to place the base plates.
Figure 1
1. The measure must be taken from center to center of the base plates. Refer to the
diagram above and confirm the place of the base plates. ENSURE THAT THE
FOUNDATIONS ARE SQUARE.
2. All the base plates need to be welded on the Containers.

5
B - FRAME INSTALLATION
Figure 2
1. Connect the Top bent tube (part code 1), the Middle Bent Tube (part code 2) and
the Sidewall Bent Tube (part code 3) with the Bolts M8x70 (part code 9); these
make one group of arches. Please NOTE the direction of the bolt. DO NOT install
the bolts on the top of the truss where the fabric will rest.
2. Insert one end of the assembled arch into one base plate and insert the other end
of the arch into the opposite base plate. Secure the arches on the baseplates using
the bolts.
Figure 3

6
3. After installing the first two arches, connect the Connection purlin (part code 4)
onto them using the Bolt M10x80 (part code 10). There are 5 pieces of Connection
purlins (part code 4) between each arch.
4. Install the Support tube (part code 5) using the Clip (part code 6). Assemble the
frame by turns like this.
Figure 4
5. Then install the third arch into the base plate and connect the purlins.
6. Install the arches one by one until the frame is finished.

7
C - ROOF COVER INSTALLATION
NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A
slight breeze is the most advantageous for cover installation. To take advantage of the
breeze, pull the cover up over the arches with the breeze blowing in the cover like a sail
filled with air.
1. Insert the Lower tensioning tube for roof cover (part code 7) into the pockets on
the end of the roof cover (part code 8). Then put the ∮ 32 Plastic plug for base rail
section (part code 12).
Figure 5
2. Put the Roof cover (part code 8) EVENLY, CAREFULLY AND SLOWLY atop the frame.
Adjust the cover so that it is square and evenly centered on the frame.
Figure 6
3. On the Roof cover, cut pockets over each ratchet on the base plates, then use the
Ratchet strap (part code 13) to tie down the Lower tensioning tubes.

8
Figure 7
4. Weld the Angle seats (part code 15) on each container and use the Rope (part code
11) to knit the cover on the two external arches. Then tie the Rope to the Angle
seats.
Figure 8

9
Please, check our installation images and videos section by clicking the following link:
https://drive.google.com/drive/u/3/folders/1p9FLejo-JIrkJPx5_Kp-hDcssOph2dWa
NOTES:
-DO NOT LEAVE THE ROOF COVER UNATTACHED UNDER ANYCIRCUMSTANCES until
the final assembly and tightening has been completed.
-The process is quite easy, but some tightening adjustments will be necessary to get
a flat, tensioned roof cover. Please adjust the roof cover every month.
-Wrap tape around the gap between the steel after installing.