Storage Canopy C6040S User manual

SHELTER
ASSEMBLY MANUAL
Model # W60 x L40 x H 15ft
C6040S Back wall & frame of Container Shelter
C6040S Back wall & frame

SPECIFICATION
Width:60 ft Length:40 ft Height:15 ft
IMPORTANT ---- READ MANUAL FIRST
Improper site preparation, Assembly and Maintenance may invalidate warranty and cause
unnecessary and costly mistake. If you have any questions contact your local dealer.
For User Friendly assembly we have identified each individual component with the part code as
indicated in the parts list. Please refer to the part code numbers and drawing to ensure problem
free assembly.
It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also re-
tighten once or twice again after a few months of use. This is important when assembly in cold
weather (autumn and winter) because the fabric is stiff then and when we got the sun and warm
weather afterwards it will make the fabric “slack” again and need to be re-tighten before next
winter.
It’s the owners responsibility to take of snow immediately if not slide off by itself.
READ ALL INSTRUCTIONS BEFOREASSEMBLY
1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in
slippery places, in high winds, or wet location.
2. Keep children away. All children should be kept away from the work area.
3. Don’t over reach. Keep proper footing and balance at all times.
4. Do not assemble in under the influence of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If
there is any doubt, do not assemble.
5. Be aware of possible windy conditions; fasten the bases in concrete if these conditions are
likely to occur. Remove the cover during hurricane.
6. Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not
expose to open flame.
7. Be aware of personal safety during assembly and use. Be careful not to pinch fingers with
clips and tubes when assembling: when using makes sure there is adequate ventilation for
exhaust and other dangerous fumes.

Parts List
Part Code
Description
Qty
1
Middle base plates
2
2
Side base plates
2
3
Base plate for winch door
2
4
Side standing leg beside the container
2
5L
Lower standing leg at left
1
5R
Bottom standing leg for installing the
winch door
1
7
Upper standing leg
2
7L
Bottom door post at left
1
7R
Bottom door post at right
1
8L
Middle door post at left
1
8R
Middle door post at right
1
9L
Upper door post at left
1
9R
Upper door post at right
1
10
Door beam
1 Group
11
Door boom
1
12
Horizontal tube for front endwall
6
12A
Top horizontal tube on side
2
13
Horizontal tube for winch wheel
1
14
Bottom tension tube on the front door
4
15
The door vertical tube
9 Group
16
Tension tube on the container
2
17
Stake peg
12
18
Mechanical wheel with wire rope
1
19
Clips
6
19A
Semiarc welded iron plate
6
19B
Straight three-hole iron plate
2
20
Bolts M12*110
2
21
Bolts M10*90
14

22
Bolts M10*90
12
23
Bolts M12*30
36
24
Bolts M10*30
4
25
Front cover
1
26
Rope
1
27
Plastic Plug
12
28
Added door frame
2
29
Added legs
2
30
Added side legs
2

EQUIPEMNT AND TOOLS FOR INSTALIATION
1. Measuring tape
2. String for alignment
3. Step ladder
4. Welder
5. Sledge hammer
6. Wrench
7. Scissors
INSTALLATION PROCESS
A—FRAME INSTALLATION
Figure 1
There are four base plate comes with the back endwall. Each of them should be placed in the
right position(especially the two base plate close to the containers.)

C--INSTRUCTION FOR COVER ATTACHED
Assembly the end cover first.
NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A
slight breeze is the most advantageous for cover installation. To take advantage of the breeze,
pull the cover up over the arches with the breeze blowing in the cover like a sail filled with
air.
Figure 2
1

.
Figure 3
The process is quite easy. But some tightening adjustments will be necessary to produce a flat. Please adjust
the cover timely.
2