SUGATSUNE LAMP DC Series User manual

Side plate
1
(24)
16
Trigger fix screw⑤
Top plate
Adjust±3
B
A
50
98
(34.5)
13
(88)
20
20 64
(33)
20
Main unit fix screw ④
Wood door
Wood door
Overlay amount
16
Wood door
Glass process dimensions AB
Inset door 88−door end gap
overlay door 88＋overlay amount
24−door end gap
Overlay amount＋24
DC-100
DAMPER CATCH DC SERIES INSTALLATION MANUAL
(DC-90,DC-90G,DC100,DC-100G)
Thank you for using our product. Before installation, please read this manual thoroughly to ensure correct installation.
Please keep this manual at hand for future reference.
■ GLASS PROCESS DIMENSIONS
(DC-90G AND DC-100G)
Prepare hole as shown right.
2×I7
Door end
Outside of door
A32
B
Top plate
Wood door
Main unit fix screw ④
Trigger fix screw⑤
Trigger fix screw ⑧
Glass door
Side plate
Adjust±3
(34.5)
A32
A
13
(52.7)
50
18.5
20
16
C22〜24
32
B
11.5
(34.5)
Overlay amount
Side plate
5
Door endgap
8
Door endgap
Top plate
20
B
Mount position AB
C−door end gap ＋3
Inset door
overlay door
C＋overlay ＋3
24 −door end gap
overlay＋24
DC-90 
C:100 to 200 mm
For inset door (glass)
For overlay door (wood)
For overlay door (wood)
（For an inset door, refer to the upper left figure.）
( The main body shows DC-90 type and DC90G type. ）
Name
/
Item No.
①Main body ②Trigger ③ Trigger
positioning jig
④ Main unit fix screw
Truss head tapping
screw 4×30
※
⑤
Trigger fix screw
Truss head tapping
screw 4×16
⑥Face plate ⑦Spacer ⑧ Trigger fix screw
Truss head scew
M4×12
DC-90 1pc 1pc 1pc 2pcs 2pcs 
DC-90G 1pc
1pc
1pc
1pc 1pc 2pcs 1pc 1pc 2pcs
DC-100 1pc 1pc 2pcs 2pcs 
DC-100G 1pc 1pc 2pcs 1pc 1pc 2pcs
※for wood top plate (20mm thick)
Caution:
 If not followed, injury or damage may result.
The product is designed for indoor use.
Temperature range: 10 to 40°C, Humidity: less than 90%
Do not use it for any purpose other than cabinet.
Do not use excessive force to the damper. It may cause damage.
This product is a part for furniture. After installation, please check the function and safety of the final product.
Use the hinges without catch.
Meaning of symbols
FOR YOUR SAFE WORK AND CORRECT INSTALLATION
COMPONENT PARTS
INSTALLATION DRAWING
Parts No. Max. Door Width Max. Door Height Glass thickness Door Weight
DC-90 — 1 −4kg
DC-90G 5 1 −4kg
DC-100 — 1.5 −7kg
DC-100G
450
450
600
600
600
600
800
8 0 0 5 1.5 −7kg
DOOR SPECIFICATION
Warning
Caution Prohibited Required

󱫀Mounting the main body
Mount the main body ①with the
screws ⑤.
※1In case of overlay door, it is 0 mm.
󱫀Mounting the main body
Mount the main body ①with the
screws ⑤.
※1In case of overlay door, it is 0 mm.
󱫂 Preparation of trigger mounting
1Connect the trigger positioning jig ③
to the main body ①.
󱫄Positioning the trigger
Please check the procedure below for correct
mounting position of the trigger ②on the door.
1Slowly close the door so that the door comes
into contact with the trigger.
󱫆Mounting and adjusting the trigger
Mount trigger ②with one
trigger fix screw ⑤.
After, adjusting to best position,
fix the trigger with another screw ⑤.
󱫈Mounting on a glass door(Illustration shows DC-100G type.)
Mount the trigger onto the glass door which has two drilled holes
as shown on the right.
For adjustment, refer to section 4 "Mounting and adjusting the trigger".
2Insert the trigger ②
into the trigger
positioning jig ③.
󱫂 Preparation of trigger mounting
1Connect the trigger positioning jig ③
to the main body ①.
2Insert the trigger ②
into the trigger
positioning jig ③.
DC-90, DC-90G
(right-side installation is shown. Left- side installation is symmetrically opposed)
DC-100 , DC-100G
Trigger fix screw⑤
Main body①arm
Trigger ②
O ring
Horizontal adjustment:
Adjust trigger position so that the
main body`s arm ①slightly
contacts the trigger O ring②.
Remove the jig to position
the trigger ②.
Vertical adjustment:
Adjust trigger position so that the
main body`s arm ①slightly contacts
the trigger O ring②at a lower
position.
Main body①arm
Trigger ②
O ring
2While holding the trigger, open the door.
Then mark the position for the trigger mounting hole.
Trigger②
Trigger fix screw ⑧
Truss head screw
M4×12
Face plate ⑥
Spacer ⑦
Door
Door
100−200
Install offsetting
by door thickness. ※1
Fit main body
①
onto the top and
side panels.
For inset doors For inset doors
Attach the trigger to
the jig as shown.
Trigger ②
Trigger positioning jig
③
Trigger ②
Attach the trigger to
the jig as shown.
Trigger positioning jig
③
trigger positioning jig ③
Fully insert
Face LAMP mark
downward.
Face LAMP mark
downward.
Fully insert
Slight contact
Do not overtighten the screws.
When using M4 screw：1〜1.5N･m
Do not overtighten the screws.
When using M4 screw：1〜1.5N･m
INSTALLATION PROCEDURE
SUGATSUNE KOGYO CO.,LTD
Tokyo, JAPAN
Phone: [phone] E-mail:[email protected]
SUGATSUNE KOGYO (UK) LTD
Reading, UK
Phone: [phone] E-mail:[email protected]
SUGATSUNE EUROPE GmbH
Dusseldorf, GERMANY
Phone: [phone] E-mail:[email protected]
SUGATSUNE SHANGHAI Co., LTD
Shanghai, CHINA
Phone: [phone] E-mail:[email protected]
Guangzhou, CHINA
Phone: [phone] E-mail:[email protected]
SUGATSUNE KOGYO INDIA PRIVATE LIMITED
Mumbai, INDIA
Phone: [phone] E-mail:[email protected]
SUGATSUNE AMERICA, INC
California, USA
Phone: [phone] E-mail:[email protected]
Chicago, USA
Phone: [phone] E-mail:[email protected].
SUGATSUNE CANADA, INC.
Phone: [phone] E-mail:[email protected]
2022.02 1517-1
Trigger positioning jig
③
Install offsetting
by door thickness. ※1
Double-sided tape may help the positioning of
the trigger. Please remove the tape before
fastening.
Slight contact
trigger positioning jig ③
2