Suncast BMS8130 User manual

а те e
|
BMS8130
and
BMS8160
ooo
||
Blow
Molded
Resin
Storage
Shed
Suncast
Products
and
OWNER'S
MANUAL
Replacement
Parts
To purchase Suncast
replacement parts and learn
about other Suncast products,
visit www.suncast.com or call
1-800-846-2345 or 1-630-879-2050
KEEP THESE INSTRUCTIONS. You will need the Quality Control Number shown below to register your product.
Quality Control Number: BMS8130 Assembled exterior dimensions 8' 4-1/2" W. x 157.9" D. x 8' 7" H.
BMS8160 Assembled exterior dimensions 8' 4-1/2" W. x 194.3" D. x 8' 7" H.
© 2013 Suncast Corporation, Batavia, IL 0361246A

Before You Begin
Consult your local authorities for any permits required to construct shed.
Prior to the construction of your shed, check with the local building code official to review any required permits or
building limitations.
Å level and sturdy foundation is required before shed construction can begin.
Site preparation information is available on pages 19-22. А foundation that differs from the suggestions within this
manual could prevent proper assembly and may damage parts.
Read instructions thoroughly prior to assembly.
This kit contains parts that can be damaged if assembled incorrectly or in the wrong sequence.
Please follow instructions.
Suncast is not responsible for replacing parts lost or damaged due to incorrect assembly.
Check for all parts before you begin assembly.
Using the provided parts check list on pages 5-18, verify that you have all the parts required to construct your
shed model.
COMPLETE SITE PREPARATION AND FOUNDATION CONSTRUCTION BEFORE UNPACKING ALL PARTS.
Assistance is required during entire assembly.
Use a rubber mallet to “push” parts into locked position. T
Á CAUTION
* Proper site preparation required.
* Shed not intended for use in extreme weather conditions.
• Shed not intended for storage of flammable or caustic chemicals.
• Store heavy items near the bottom of shed.
• Shed not intended for use by children.
* DO NOT stand, sit, or store items on storage shed roof.
* Treat carefully in extreme temperatures.
* Repair or replace broken parts immediately.
• Suncast is not responsible for damage caused by weather or misuse.
* At regular intervals inspect your shed to make sure that assembly integrity has been maintained.
* Periodically check that the location you have chosen to set your shed is still level.
* This kit contains parts with metal edges. Please be careful when handling.
Shed Safety and Care
* Hot items, such as recently used grills, blowtorches, etc., must not be stored in the shed.
* Heavy articles should not be leaned against the walls, as this may cause panel distortion and permanent damage.
* Keep roof clean of snow and leaves.
* The shed walls and roof sections have a textured exterior, much like vinyl home siding. Over time, dust may
accumulate in the texture. When combined with moisture, this could encourage the growth of moss or mold on the
shed. To maintain the look of your shed, we recommend cleaning it each year with mild soap and water. DO NOT
use bleach, ammonia, or other caustic cleaners, and DO NOT use stiff bristle brushes. Failure to perform annual
cleaning could result in permanent staining of the plastic. This is not a manufacturing defect and is not covered
under warranty.

Assembly Day Tips
• Complete site preparation and foundation construction before unpacking parts and beginning assembly.
e DO NOT attempt to assemble on a day with strong winds.
• DO NOT attempt to assemble on days when temperature is below 32 degrees.
e Set aside appropriate amount of time to completely assemble shed.
* Make sure you have assistance nearby to lift and secure parts in place.
* Wear light duty work gloves while assembling shed.
* Once roof is assembled, a flashlight may be of use when assembling smaller components inside shed.
• DO NOT use a torque wrench or hand drill to tighten provided Easy Bolts. Use 010210410 Easy Bolt Easy Driver
tool (provided) ONLY.
e Suncast provides extra hardware for small fasteners for customer convenience. In some cases, there will be extra
small fasteners once the assembly is complete.
Note: This product contains parts that are used in different orientations to construct the shed. Please take note of the
orientation of the parts shown throughout this instruction manual. Failure to follow instructions could result in damage to
parts. Suncast is not responsible for replacing parts lost or damaged due to incorrect assembly.

BMS8130 and BMS8160 Expansion Kit Overview
BMS8700 + 2 Expansion kits =
BMS8130
BMS8100 + 1 Expansion kit =
BMS8700 + 3 Expansion kits =
BMS8160
BMS8100 + 2 Expansion kits =

Parts - Expansion Kit
о 9
0280408A — 0800172 —
Ridge beam joiner Left roof extension
e MT.
Header lag 0631094 —
Support Truss leg
Bracket 2
х2
0280446 —
Truss bracket
0280447 — || 0631095 — Truss ~
D
ш.
cross
beam
0631248 —
Full length side adapter
bracket 0B00164 —
x2 Left floor extension
Ф
0440691 –
Skylight sealing gasket
х2
z
Ф
010223107 –
Skylight
0B00170 —
Right roof extension
0440693 —
Extension bracket
0B00160 —
Side panel
0B00169 —
Right floor extension

Parts — Doors (8100 or 8700)
О о D
0440690 — 0B00163 — 0440631 —
Door window Left door D-ring bolt
X1 set X1 set
0102086 — Door 0440655 — Door 0B00162 —
window frame window gasket Right door
х2 X1 set

0800156 —
Rear corner
х2
0B00160 —
Side panel
х2
7;
0B00166 —
Right front corner
0B00174 —
Right floor
0800157 —
Shelf
0B00173 —
Left floor
o
Ben
О ©
Ta
о
=
б Ei = o ©
~
со U)
= са
0800165 –
Left front corner
Parts

Parts - BMS8700 Headers
d
0280406 — Ridge beam
0B00159 — 0440630 — 0280372А — 0B00161 —
Front header Vent screen Header beam Rear header
X1 set х2

Parts - BMS8700 Truss
Ф ©
0631094 — 0631096 —
Truss leg Truss bracket
x2
0631095 — Truss
cross beam
х2
D
0440694 — Roof
support bracket
X1 set
0631093 —
Truss strap
х2
0630817A — Side
adaptor bracket
х2

Parts - ВМ58700 Roof
о
0800167 – 010223107 –
Left roof Skylight
х2 х4
Q
10
RSA,
S У NS
SOSI
SIRI
NS
Q
0440691 —
Skylight sealing gasket
X2 sets
0B00168 —
Right roof
X2