Sunny Health & Fitness ESSENTIAL POWER RACK SF-XF920063 User manual

ESSENTIAL POWER RACK
SF-XF920063
USER MANUAL
IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your
satisfaction is very important to us,PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED
US: [e-mail] or 1- 877 - 90SUNNY (877-907-8669).

1
IMPORTANT SAFETY INFORMATION
We thank you for choosing ourproduct.To ensure your safety and health, please use this equipment
correctly. It is important to read this entire manual before assembling and using the equipment. Safe
and effective use can only be achieved if the equipment is assembled, maintained, and used
properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings
and precautions.
1. Before starting anyexercise program, you should consult your physician to determine if you have
any medical or physical conditions that could put your health and safety at risk or prevent you
from using the equipment properly. Your physician’s advice is essential if you are taking
medication that affects your heart rate, blood pressure, or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest,
irregular heartbeat, shortness of breath, lightheadedness, dizziness, orfeelings of nausea. If you
do experience any of these conditions, you should consult your physician before continuing with
your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet.
To ensure safety, the equipment should have at least 2 feet (60 CM) of free space all around it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of
the equipment can only be maintained if it is regularly examined for damage and/or wear and
tear.
6. Always use the equipment as indicated. If you find any defective components while assembling
or checking the equipment, or if you hear any unusual noises coming from the equipment during
exercise, discontinue use of the equipment immediately and do not use until the problem has
been rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that maybecome
entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment.
9. The maximum weight capacity of this unit is 800 pounds (360KG).
10.The equipment is not suitable for therapeutic use.
11.To avoid bodily injury and/or damage to the product or property, proper lifting and moving are
required.
12.Your product is intended for use in cool and dry conditions. You should avoid storage in extreme
cold, hot or damp areas as this may lead to corrosion and other related problems.
13.This equipment is designed for indoor and home use only; it is not intended for commercial use.

2
EXPLODED DIAGRAM
1
4
5
5
6
12
4
2
7
7
8
8
8
8
9
9
10
10
13
13
13
13
14
14
19
19
15
15
16
16
18
18
20
20 20
20 20
20
20
21
21
21
21 3
21
24
24
21
21 2421
21
21 21
21
21
21 21
25
21
21 21 24 24 21
21
22
22 23
23
26
23 26
23
26
23
21
26
23
21
17
17
27
11
17
17
27
21
21 21
#28 2PCS
21
24
21
24
25
#29 1PC

3
HARDWARE PACKAGE
#21-∮20*∮10.5*1.5mm 46PCS #28- #13-17 2PCS
#22-M10*20mm 2PCS
#23-M10 6PCS
#24-M10 20PCS
#20-M10*70mm 16PCS
#25-M10*65mm 4PCS
#26-M10*30mm 4PCS
#29-6mm 1PC
PARTS LIST
No. Description Spec. Qty. No. Description Spec. Qty.
1
Right Base Frame
1
16
Round End Cap
2
2 Left Base Frame 1 17
Rubber Pad
4
3
Rear Cross Tube
1
18
Square End Cap
2
4
Lower Upright Frame
2
19
Round End Cap
2
5
Upper Upright Frame
2
20
Hex Bolt
M10*70mm
16
6
Upper Frame
1
21
Flat Washer
∮
20*
∮
10.5*1.5mm
46
7 Weight Plate Holder 2 22 Hex Socket Head
Bolt M10*20mm 2
8
Gusset Plate
4
23
Spring Washer
M10
6
9
Connection Plate
2
24
Lock Nut
M10
20
10 Metal Plate 2 25 Hex Socket Head
Bolt M10*65mm 4
11 Right Hook 1 26 Hex Bolt M10*30mm 4
12
Left Hook
1
27
Phillips Screw
M6*15
16
13
Foot End Cap
4
28
Wrench
#13-17
2
14
U-Bracket
2
29
Allen Wrench
6mm
1
15
Bumper
∮
100*
∮
50*15
2
Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:
The model number (found on cover of manual)
The product name (found on cover of manual)
The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the front
of the manual)
Please contact us at [e-mail] or 1- 877 - 90SUNNY (877-907-8669).

4
ASSEMBLY INSTRUCTIONS
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY (877-
907-8669).
#20-M10*70mm 4PCS
#21-∮20*∮10.5*1.5mm 8PCS
#24-M10 4PCS #28- #13-17 2PCS
1
2
20
20
21
21
21 21
21
21
21
21
9
9
24
24
3
13
13
13
13
#20-M10*70mm 4PCS
#21-∮20*∮10.5*1.5mm 8PCS
#24-M10 4PCS
#28- #13-17 2PCS
6
5
5
20
21
21
21
21
21
20
10
10
24 24
STEP 1:
Attach 4 Foot End Caps (No. 13) into the
two sides of the Right &
Left Base
Frames (No. 1 & No. 2).
Attach the Rear Cross Tube (No. 3) and 2
Connection Plates (No. 9) to the Right &
Left Base Frame (No. 1 & No. 2) using 4
Hex Bolts (No. 20),8Flat Washers (No.
21) and 4 Lock Nuts (No. 24).Tighten and
secure with 2 Wrenches (No. 28).
STEP 2:
Attach the Upper Frame (No. 6) and 2
Metal Plates (No. 10) onto 2 Upper
Upright Frames (No. 5) using 4 Hex Bolts
(No. 20),8Flat Washers (No. 21) and 4
Lock Nuts (No. 24).Tighten and secure
with 2 Wrenches (No. 28).
There are 3 height installation options for
the Upper Frame (No. 6), make sure the
two sides of Upper Frame (No. 6) are the
same height when installing.
NOTE: The Upper Upright Frames (No.
5)
have decals that say UP. The ends with
the UP decal should be attached to the
Upper Frame (No. 6).

5
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY (877-
907-8669).
#25-M10*65mm 4PCS
#21-∮20*∮10.5*1.5mm 10PCS
#24-M10 4PCS
#28- #13-17 1PC
#22-M10*20mm 2PCS #23-M10 2PCS
#29-6mm 1PC
24
24 21
21
21
21
21
21
21
21
23
23
22
22
5
5
4
4
25 25
#26-M10*30mm 4PCS
#21-∮20*∮10.5*1.5mm 4PCS
#23-M10 4PCS
#28- #13-17 1PC
4
4
26 26
26 26
23
23
23
21 21
21
1
2
22
STEP 3:
Attach 2 Lower Upright Frames (No. 4) to
the 2 Upper Upright Frames (No. 5) using
4Hex Socket Head Bolts (No. 25),10
Flat Washers (No. 21), 4 Lock Nuts (No.
24), 2 Hex Socket Head Bolts (No. 22)
and 2Spring Washers (No. 23).Tighten
and secure with 1 Wrench (No. 28) and 1
Allen Wrench (No. 29).
NOTE: The 4 Hex Socket Head Bolts (No.
25) should be inserted from inside of frame
towards the outside, the 4 Lock Nuts (No.
24) should be on the outside of the Upper
Upright Frames (No. 5).
STEP 4:
NOTE: It is highly recommended that you
have assistance during the assembly.
Before assembly, please make sure the 2
Hex Socket Head Bolts (No. 22) showed
on Fig A are facing towards the back of the
rack, it will help to install the Left Hook
(No. 12) & Right Hook (No. 11) smoothly
in STEP 7.
Attach the assembled 2 Lower Upright
Frames (No. 4) to the Right & Left Base
Frames (No. 1 & No. 2) using 4 Hex Bolts
(No. 26),4 Spring Washers (No. 23) and
4Flat Washers (No. 21).
Tighten and
secure with the Wrench (No. 28).
Fig. A

6
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY (877-
907-8669).
#20-M10*70mm 8PCS
#21-∮20*∮10.5*1.5mm 16PCS
#24-M10 8PCS
#28- #13-17 2PCS
1
2
8
8
8
8
20
20
20
20
21
21
21
21
21
21
21
21
24
24
1
2
7
15
7
15
STEP 5:
Attach 4 Gusset Plates (No. 8) to the
Right & Left Base Frames (No. 1 & No.
2) using 8 Hex Bolts (No. 20),16 Flat
Washers (No. 21) and 8 Lock Nuts (No.
24). Tighten and secure with 2 Wrenches
(No. 28).
STEP 6:
Attach 2 Weight Plate Holders (No. 7) to
the Right & Left Base Frames (No. 1 &
No. 2). Tighten the 2
Weight Plate
Holders (No. 7).
Insert 2 Bumpers (No. 15) into 2Weight
Plate Holders (No. 7) as shown in Fig.A.
Fig. A

7
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY (877-
907-8669).
5
12
11
5
STEP 7:
Insert Left Hook (No. 12) into the Upper
Upright Frames (No. 5) on the left. Turn
Left Hook (No. 12) as the arrow showed
on the left picture to tighten.
Insert Right Hook (No. 11) into the Upper
Upright Frames (No. 5) on the right. Turn
Right Hook (No. 11) as the arrow showed
on the left picture to tighten.
Place them atthe same levelon the left and
right side of the cage and at a comfortable
height that will
assist you during your
workout.
The assembly is complete!

8
MAINTENANCE INSTRUCTIONS
DAILY MAINTENANCE
Inspect and tighten all parts regularly. (Nuts, Bolts, Rubber Pads, Steel Brackets, etc.)
Replace any worn or torn parts immediately.
Check and ensure the equipment is levelled at all time.
Check and tighten all adjustment pins/knobs regularly.
WEEKLY MAINTENANCE
Use damp cloth on plastic parts only, use dry cloth on metal frames.
Inspect the metal frame structure of the equipment.
Version 1.1