Sunny Health & Fitness EVOLUTION PRO II User manual

EVOLUTION PRO II MAGNETIC BELT
DRIVE INDOOR CYCLING BIKE
SF-B1986
USER MANUAL
IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your
satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED
US: [email protected] or 1- 877 - 90SUNNY (877-907-8669).

1
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this
equipment correctly. It is important to read this entire manual before assembling and using the
equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained,
and used properly. It is your responsibility to ensure that all users of the equipment are informed of
all warnings and precautions.
1. Before starting any exercise program, you should consult your physician to determine if you
have any medical or physical conditions that could put your health and safety at risk or prevent
you from using the equipment properly. Your physician’s advice is essential if you are taking
medication that affects your heart rate, blood pressure, or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest,
irregular heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of nausea. If you
do experience any of these conditions, you should consult your physician before continuing with
your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet. To
ensure safety, the equipment should have at least 2 feet (60 CM) of free space all around it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of
the equipment can only be maintained if it is regularly examined for damage and/or wear and
tear.
6. Always use the equipment as indicated. If you find any defective components while assembling
or checking the equipment, or if you hear any unusual noises coming from the equipment during
exercise, discontinue use of the equipment immediately and do not use until the problem has
been rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may become
entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment.
9. The maximum weight capacity of this unit is 330 pounds (150 KG).
10.The equipment is not suitable for therapeutic use.
11.To avoid bodily injury and/or damage to the product or property, proper lifting and moving is
required.
12.Your product is intended for use in cool and dry conditions. You should avoid storage in extreme
cold, hot, or damp areas as this may lead to corrosion and other related problems.
13.This equipment is designed for indoor and home use only, it is not intended for commercial use.

2
EXPLODED DIAGRAM

3
PARTS LIST
No.
Description
Spec.
Qty.
No.
Description
Spec.
Qty.
1
Main Frame
1
53
Self-tapping Screw
M4.2x10
13
2
Front Stabilizer
40x80x2T
1
54
Hex Bolt
M6x35
1
3
Rear Stabilizer
40x80x2T
1
55
Idle Wheel Fixture
1
4
Handlebar Post
40x80x2T
1
56
Nylon Nut
M10x9T
2
5
Seat Post
40x80x2T
1
57
Steel Sleeve
Φ25.1x32x10T
1
6
Handlebar
Φ25.4x2T
1
58
Steel Bearing
6005-2RS
2
7
Seat Column
1
59
C-ring
Φ20
2
8
Plastic Fastener
50x100mm
2
60
C-ring
Φ25
1
9
Seat
VL-6100
1
61
Idle Wheel
1
9A
Nut
M8
2
62
Wave Washer
27x34x0.3T
1
10
Flywheel
Φ468
1
63
Plastic Washer
10x20x2T
2
11
Belt Wheel w/ Axis
Φ260
1
64
Plug
Φ17
3
12
Belt
1590 PK5
1
65
Steel Sleeve
Φ10.2x15x6T
1
13
Right Belt Cover
1
66
Axis
Φ20x155mm
1
14
Left Belt Cover
1
67
Wave Washer
21x27x0.3T
1
15
Right Inner Cover
1
68
Washer
20.5x25x0.5T
1
16
Left Inner Cover
1
69
Hex Bolt
M10x32
1
17
Side Trim Cover
1
70
Washer
12x17x1.0T
2
18R
Right Crank
1
71
Plastic Bearing
Φ12.8x21.4x6.7T
4
18L
Left Crank
1
72
Plastic Sleeve
Φ7.9x12.7x23.5
2
19
Cap for Crank
2
73
Fixed Plate
2
20
Dumbbell Bracket
1
74
Cushion Knob
M10x25
4
21
Spring Knob
M16x26
2
75
Cap
Φ76
4
22
L-shaped Knob
M10x20
1
76
Transportation
Wheel
Φ70
2
23
Knob
M10x28
1
77
Tension Control
Knob
M10
1
24
Lock Nut
M10
1
78
Screw
M5x15
4
25
Washer
d19.5xФ38x2T
1
79
Bolt
M5x10
2
26R
Right Plastic Cover
For Magnet
1
80
Self-tapping Screw
M4.5x25
5
26L
Left Plastic Cover
For Magnet
1
81
Plastic Cap
1
27
Support Bar
20x20x1.4T
1
82
Washer
12x24x1.5T
2
28
Magnet Bracket
1
83
Washer
Φ5
2
29
Brake Rod
1
84
Plastic Cover
1
30
Fixed Cover
1
85
Washer
10x20x2T
1
31
Groove Fastener
2
86
Plastic Spacer
34.8x34.8x6T
1
32
Spring Washer
1
87
Oval Cover
1
33
Nylon Nut
M6
2
88
Self-tapping Screw
2
34
Nylon Nut
M8
2
89
Wrench
S14 S17
1
35
Cap Nut
M10
4
90
Wrench
S13 S15
1
36
Carriage Bolt
M10x55
4
91
Computer
TZ-4110
1
37
Washer
d10xФ19x1.5T
6
91A
Pulse Cable
1
38
Hex Nut
M10x6T
4
91B
Plug Cable
1
39
Hex Socket Bolt
M8x38
2
92L
Left Lock Nut
9/16”
1
40
Spring
Φ2.6x18
1
92R
Right Lock Nut
9/16”
1
41
Adjustment Bar
Φ6x60
1
93
Spanner
S14 S17 S19
1
42
Compressed Spring
Φ1.5x9
1
94R
Right Pedal
JD-014
1
43
Crank Plug
2
94L
Left Pedal
JD-014
1
44
Flange Nut
M12x1.5
4
95
Hand Pulse Sensor
2
45
Hex Socket Bolt
M8x15
3
96
Tapping Screw
ST4.2x16
2
46
Washer
d10xФ29x2T
2
97
Hand Pulse Cable
1
47
Self-tapping Screw
M5x12
3
98
Tapping & Drilling
Screw
ST4.2x16
1
48
Bottle Holder
1
99
Sensor Magnet
1
49
Screw
M5x10
2
100
Computer Cable
1
50
Philips Screw
M3x10
1
101
Sensor Cable
1
51
Steel Sleeve
Φ12x17x9
1
102
Sensor Bracket
1
52
Self-tapping Screw
M4.5x15
2
103
Allen Wrench
S4
1

4
HARDWARE PACKAGE
Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:
The model number (found on cover of manual)
The product name (found on cover of manual)
The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the
front of the manual)
Please contact us at [email protected] or 1- 877 - 90SUNNY (877-907-8669).
#23 M10X28 1PC
#22 M10 1PC
#35 M10 4PCS
#24 M10 1PC
#36 M10x55 4PCS
#25 d19.5xФ38x2T 1PC
#37 d10xФ19x1.5T 4PCS
#46 d10xФ29x2T 2PCS
# 89 S14 S17 1PC
# 90 S13 S15 1PC
#93 S14 S17 S19 1PC
#103 S4 1PC

5
ASSEMBLY INSTRUCTIONS
We value your experience using Sunny Health and Fitness products. For assistance with parts
or troubleshooting, please contact us at [email protected] or 1-877-90SUNNY
(877-907-8669).
STEP 1:
Attach Rear Stabilizer (No. 3) to Main
Frame (No. 1) using 2 Carriage Bolts (No.
36), 2 Washers (No. 37), and 2 Cap Nuts
(No. 35). Tighten with Wrench (No. 89).
Attach Front Stabilizer (No. 2) to Main
Frame (No. 1) using 2 Carriage Bolts (No.
36), 2 Washers (No. 37) and 2 Cap Nuts
(No. 35). Tighten with Wrench (No. 89).
#35 M10 4PCS
#36 M10x55 4PCS
#37 d10xФ19x1.5T 4PCS
#23 M10x28 1PC
#46 d10xФ29x2T 1PC
#25 d19.5xФ38x2T1PC
STEP 2:
Unscrew Spring Knob (No. 21) from the
Main Frame (No. 1).
Insert Handlebar Post (No. 4) into Main
Frame (No. 1) and attach with Spring
Knob (No. 21).
STEP 3:
Secure the Handlebar (No. 6) onto the
Handlebar Post (No. 4) using Knob (No.
23), Washer (No. 46), Washer (No. 25),
and Lock Nut (No. 24).
Insert Computer (No. 91) onto computer
holder on the Handlebar (No. 6).
Connect Computer Cable (No. 100) with
Plug Cable (No. 91B) from the Computer
(No. 91);
Connect Hand Pulse Cable (No. 97) with
Pulse Cable (No. 91A) from the Computer
(No. 91).
#21 M16x26 1PC
#35 M10 4PCS
#36 M10x55 4PCS
#37 d10xФ19x1.5T 4PCS
#23 M10x28 1PC
#46 d10xФ29x2T 1PC
#25 d19.5xФ38x2T 1PC
#24 M10 1PC
#89 S14 S17 1PC

6
We value your experience using Sunny Health and Fitness products. For assistance with parts
or troubleshooting, please contact us at [email protected] or 1-877-90SUNNY
(877-907-8669).
STEP 4:
Loosen 2 Nuts (No. 9A) on Seat (No. 9), and
then attach Seat Column (No. 7) to Seat (No.
9) and re-tighten the Nuts (No. 9A) with
Wrench (No. 90).
Insert the Seat Column (No. 7) into Seat
Post (No. 5) and tighten using the L-shaped
Knob (No. 22) and Washer (No. 46).
STEP 5:
Remove the Right Lock Nut (No. 92R)
located on the Right Pedal (No. 94R). Screw
the Right Pedal (No. 94R) clockwise into
Right Crank (No. 18R). Once the pedal is in
place, use Wrench (No. 90) to hold the bolt of
the pedal. Securely screw the Right Lock Nut
(No. 92R) counter-clockwise into the thread
end of the Right Pedal (No. 94R) with
Spanner (No. 93).
Remove the Left Lock Nut (No. 92L) located
on the Left Pedal (No. 94L). Screw the Left
Pedal (No. 94L) counter-clockwise into Left
Crank (No. 18L). Once the pedal is in place,
use Wrench (No. 90) to hold the bolt of the
pedal. Securely screw the Left Lock Nut (No.
92L) clockwise into the thread end of the Left
Pedal (No. 94L) with Spanner (No. 93).
STEP 6:
Adjust the bolt on the Bottle Holder (No. 48)
with provided Allen Wrench (No. 103) to your
preferred size.
Remove the 4 Screws (No. 78) on the forks of
the Main Frame (No. 1).
Re-attach 2 Screws (No. 78) back onto the left
fork of Main Frame (No. 1) along with the
Bottle Holder (No. 48). Tighten with Spanner
(No. 93).
Re-attach 2 Screws (No. 78) back onto the
right fork of Main Frame (No. 1) along with the
Dumbbell Bracket (No. 20). Tighten with
Spanner (No. 93).
The assembly is complete!
#46 d10xФ29x2T 1PC
#22 M10x20 1PC
#90 S13 S15 1PC
#90 S13 S15 1PC
---#93 S14 S17 S19 1PC
--#93 S14 S17 S19
1PC
---#103 S4 1PC
#92R 9/16”1PC
#92L9/16”1PC
#78 M5X15 4PCS

7
BATTERY INSTALLATION AND REPLACEMENT
BATTERY INSTALLATION:
1. Take out 2 AAA batteries from the Computer (No. 91) box.
2. Press the buckle of battery cover on the back of the Computer (No. 91), then remove battery
cover.
3. Install 2 AAA batteries into the battery case on the back of the Computer (No. 91). Pay attention
to the battery + and – ends before installing.
4. Press the buckle of battery cover, then put the battery cover back to the back of the Computer
(No. 91).
The installation is complete!
BATTERY REPLACEMENT:
1. Press the buckle of battery cover on the back of the Computer (No. 91), then remove battery
cover.
2. Remove the 2 old AAA batteries in the battery case and install 2 new AAA batteries into the
battery case on the back of the Computer (No. 91). Pay attention to the battery + and – ends
before installing.
3. Press the buckle of battery cover, then put the battery cover back to the back of the Computer
(No. 91).
The replacement is complete!
NOTE: Always change both batteries at the same time. Do not mix battery types and do not mix old
and new batteries. Dispose batteries according to your state and regional guidelines.

8
EXERCISE COMPUTER
FUNCTION BUTTONS
MODE:
Press to select the function displayed or enter value during setting mode.
Press and hold for 2 seconds to enter the RACE MODE interface during stop mode.
SET:
To set up the target value of TARGET, TIME, DIST, and CAL.
Press the button and hold for 2 seconds to speed up the increment during
stop mode.
RESET:
Press the button to reset function value during setting mode.
Press the button and hold for 2 seconds to reset all value to zero.
(When the user replaces the batteries, all values will reset to zero.)
FUNCTIONS:
SPEED: Displays the speed from 0 to 99.9 KPH or MPH.
AVG SPEED: Displays the average speed only in STOP mode.
MAX SPEED: Displays the maximum speed only in STOP mode.
CADENCE (RPM): Displays the frequency per minute from 0 to 999.
AVG CADENCE (AVG RPM): Displays the average cadence (RPM) in STOP mode.
MAX CADENCE (MAX RPM): Displays the maximum cadence (RPM) in STOP mode.
DISTANCE (DIST): Accumulates total distance from 0.0 to 999.9 KM or Miles. User can preset
TARGET DISTANCE by pressing MODE & SET.
TARGET DISTANCE (TGT DIST): Users can preset the Distance in the TARGET mode.
CALORIES (CAL): Accumulate total Calories from 0.0 to 9999. User can preset target calories.
RACE: Exercise in the TARGET MODE.
TIME: Accumulates total time from 00:00 to 99:59. User can preset target Time.
TARGET TIME: Users can preset the Time in the TARGET MODE.
PULSE: Display the current pulse rate.
MILES OR KILOMETERS SETTING:
The default setting is miles. Press and hold SET and MODE together for 2 seconds to change to
kilometers.
SET TARGET VALUES:
1. Press SET to select a target value. CADENCE will start to flash.
2. Press and hold SET and the value will increase continuously.
3. Press MODE to enter.
4. TIME will flash.
5. Press SET to select a value.
6. Press MODE to enter.
7. Repeat to select values for DIST and CAL.

9
1. TARGET: the preset CADENCE.
2. In STOP mode, press SET key to enter the TARGET setting in stop mode. Press SET to increase
the CADENCE five at a time. The setting change is 15 →20→……110→115→120→15→20
→……→115→120→15 →20→……
3. The setting range of 15 -120 (Preset value is 60 CADENCES which equals six bars).
4. Each bar equals 10 CADENCE. Total is 12 bars.
Each arrow equals 10 CADENCES (1-10 CADENCES displays one arrow, 11-
20 displays two). The maximum arrows displayed is 12.
This down arrow next to the bicycle icon will be displayed when the current
CADENCE is more than the TARGET CADENCE. The bicycle icon will be displayed during exercise
mode.
RACE MODE:
Press and hold MODE for 2 seconds to enter RACE mode.
In RACE MODE, only TIME and DIST can be set.
Default values for 10 minutes / 4 (KM or Miles).
Total is 10 bars.
PULSE:
To measure the pulse, press MODE until computer is on the PULSE function. Hold the hand pulse
sensors for at least 5 seconds to measure your pulse. This value is for reference only. It cannot be
used as the basis for medical treatment.
BATTERY: This computer uses two AAA batteries. If the display appears incorrectly or becomes
difficult to read, please install new batteries. Always change both batteries at the same time. Do
not mix battery types and do not mix old and new batteries. Dispose batteries according to your
state and regional guidelines.
When Current CADENCE is less than Target CADENCE,
the up arrow next to the bicycle will be displayed.