SWorkz S35-GT2 User manual

2
INSTRUCTION
What a remarkable date January the 18th 2020 was. SWORKz won its first World championship. And
not just one title, no, but two titles. SWORKz Factory Team driver Jörn Neumann won the GT World
Championship with his SWORKz S35-GT in the Nitro category and his SWORKz S35-GTE in Electric.
Based on the world champion winning car S35-GT platform, SWORKz further developed their nitro GT and
came out with the S35-GT2.
The S35-GT2 is designed for pure On-road racing. It has a unique brand new design front and rear
suspension system. The new front Ackerman steering system now comes direct from the 1/8th S35-4 nitro
Buggy. Updated from S35-GT and a recalculated new center 2 speed ratio transmission system gives plenty
of improvements to the S35-GT2.
The S35-GT2 features a T7075 hard anodized and lightened aluminum wide layout chassis that was tested
for a long time by our factory pilots to guarantee the best performance.
The totally new developed HET di󰀨erentials are included to provide more traction which was not possible
with old system.
The new S35-GT2 comes with a lower shock layout for the front and rear. Newly developed shocks are now
catered to this new optimized layout.
The latest steering geometry, with new Ackerman and steering plates, gives the driver very accurate
feedback and control over the S35-GT2.
With the new toe in plates, which now contain square inserts, you can adjust the geometry of your
SWORKz S35-GT2 to suit any track layouts and track conditions. Lower front and rear arms are made with
a newly developed composite materials.
Another new development in the SWORKz S35-GT2 is a totally new rear hub system. Composite material
combined with Carbon plates gives you the possibility for various setups. The newly developed Composite
material works perfectly together with the HET di󰀨erentials to provide maximum traction and control.
There are many more small changes and smart ideas put into your new SWORKz S35-GT2, that make the
car a real winner.
The secret of a modern racing car is the possibility to adapt the setup to every track not just for the top
drivers but also a standard setup that works on most tracks for all hobby drivers.
Your SWORKz S35-GT2 has these two characteristics.
The SWORKz development team focused on using materials of the highest quality standards when
designing the car. You will nd 100% SWORKz top quality in the S35-GT2 kit.
Congratulations on your purchase of the new SWORKz S35-GT2 1/8 scale on-road racing GT Car pro kit
and thanks for trusting in SWORKz.
Please read this manual carefully, before you start building and driving your SWORKz S35-GT2. This
manual contains step-by-step instructions to helping you completing, preparing and ne tuning your buggy
for racing. Updates, setups, and product news will be posted on all SWORKz digital media.
As always, if you should ever have any questions or need help with your SWORKz products, please feel
free to contact our o󰀩cial SWORKz dealers and distributors.
S35-GT2 Kit Features:
• New T7075 Hard Anodized, Lightened Aluminum Chassis
• New F/R Shock Towers
• New Shock Caps
• New 3mm Updated Rear Shock Studs
• New Ackerman Plate
• New Steering System
• New Servo Saver Aluminum Part
• New Servo Saver Fixable Nut
• New Servo Saver Plate
• New Servo Saver Post Locking Design
• New Steering Balls
• New Steering Knuckle Plates
• New Updated Toe In Plates with Square Inserts
• New Lower Front and Rear Arms
• New Front Upper Arms
• New Composite Rear Hubs with Carbon Plates
• New Multi Adjustable Ball System for Rear Upper Arms
• New Anti-clock Screws for Shocks
• Front/Rear HET Di󰀨erentials Included
• New center 2 speed on-road transmission gear ration system
• 2 Front Chassis Braces Included
• More Balance Weight Positions
• Stronger Down stop Area
• Optimized Composite Material Aluminum Parts in T7075

3
WARRANTY
Your SWORKz S35-GT2 Pro kit warranty covers workmanship and manufacturing
defects of the original and unmodified parts. Warranty claims resulting from
crashes, abuse, improper operation, improper mounting, improper adjustment or
lack of maintenance will not be honored.
Contact your local hobby shop or SWORKz distributor for all claims and
questions. Claims must be well documented. All Claims are subject to expert
examination approval by SWORKz.
Specification
Length: 490mm
Width: 308mm
Height: 145mm
Ground Clearance: 15mm
Wheelbase: 325-330mm
Track: F:304mm / R:308mm
Gear Ratio: C:57/61,18/23T, F/R 43/13T
Weight: 3450g

4
INDEX
This radio controlled racing car is not a toy!
This high-performance R/C model is recommended for ages 14 and older.
Instruction 2
Warranty 3
Index 4
Required equipment for operation 5
Operation guide 6
Assembly steps 7-36
Set-up sheet 37
Blank set-up sheet 38-39
S35-GT2 Key No. List 40-41
S35-GT2 Spare Part List 41-42
S35-GT2 Option Part List 43
Explosion view with spare parts number 44-47
End cover 48

5
Starter box
Engine Starting Equipment
Glow Plug
Double-sided tape
Paint
Long nose pliers
Modeling knife
Instant cement Thread lock
Included items
Hex wrench
1.5mm
2mm
2.5mm
1.5mm
2mm
2.5mm
Fuel bottle
Glow plug wrench
Screwdriver
Screwdriver
Radio Gear Nitro fuel
Stick Type
Throttle servo
Receiver batteries
Wheel & Trigger Type
Receiver
On/Off Switch
We recommend that you use fuel
containing 20~25% nitro.
Steering servo
SP-80108
SP-80107
S-POWER Exhaust
Manifold for GT (70mm)(Made by O.S.)
S-POWER EFRA 2042 Tuned Pipe
with GT-Manifold Set(Made by O.S.)
Tools Recommended
Engine Recommended
Suggestion to using .21 1/8 GT On road Engine and pipes.
Side cutter
Curved scissors
Grease
ST-3 Turbo Plug
ST-4 Turbo Plug
Required Equipment for Operation

6
overturn
Assemble for
4 sets
Assemble for
2 sets
Assemble both left
and right sides
Assemble in the
specied order
Assemble front
and rear
Thread Locking
Compound
Grease Pure Silicone Oil Air lter oil
Operation Guide
Safety Precautions
The SWORKz S35-GT2 is a high performance radio control model which needs to be operated
with caution and common sense.
The S35-GT2 Pro Kit is not intended for children under the age of 14 without adult
supervision. SWORKz shall not be held liable for any loss or damages, whether direct,
indirect, act of nature, arising from the abuse or misuse of this product or any other product
required while operating this model.
- The nitro fuel can be dangerous is improperly handled.
- Always keep your nitro fuel in a cool area and never use near flame, sparks, or while
smoking.
- Keep your nitro fuel, and all other ammables, out of the reach of children.
- Always run your model in a well ventilated area outdoors. Never run your model indoors.
- After running your car, all parts of the engine and exhaust can become extremely hot. Be
careful not to touch these parts especially when refueling, or making repairs.
- This model is controlled by your radio controller and is sometimes vulnerable to interference
from many outside sources. This interference can cause a loss of control so it is necessary to
operate this model in an open area to avoid personal, or property damage. Always ensure
turning on your radio rst.
- Keep all the parts included in the package out of reach of children.
- This model contains many fast rotating parts. Never touch them during operation.
- Follow the instructions included with your radio gear.
- Never operate your model near people or property. The speed of this model has the
potential to injure and or damage people and or property.
- Always use original SWORKz spare parts and option parts.
- Always ensure that the buggy is in proper working condition before use.

7
1
2
BAG B
338027
116006R
330015
328001 400002
101039
210091
116006R
338024
101039
330015
328001
400002
330015
Pin M2.2x9.9mm x4
400002
O-ring S5 4.8X1.5 x4
101004
Washer 3.5X10X0.2mm x8
Fill the di󰀨erentials
with oil up to 80%
above the satellite
gears.
Put the SWORKz
Di󰀨. Oil 500000cps
for the front Di󰀨.
and 50000cps for
the rear Di󰀨.
Remember to apply a light coat of
grease to the o-ring, then slide it over
the shaft of the out drive and seat it in
the di󰀨 case.
Insert the pin through the hole in the
di󰀨 case and through the hole in the
shaft of the out drive.
OK! NG!
338027
101039
Washer 5x12x0.3 x2
101004
101004
101004
101004
610023
328001
328001
338025
328001
108001
108001
338025
S35-3W Bevel Gear Shaft x4
116006R
Ball Bearing 8x16x5mm (Red Rubber Case) x4
108001
M3x12mm FH/ST HEX Screw x8

8
4
BAG C3
330809
330832
330802AH
108026
116018
116006R
330811
104010
104016
330802AH
330832
330810
104016
104010
330812
116006R
330811
116018
104010
M5x4mm Set Screw (Flat Bottom) x2
108026
330803
330804A
200708
200709
108026
M3x5mm FH/ST HEX Screw x6
116018
Ball Bearing 8x12x3.5mm x2
330833
S35GT 2nd Speed Spring Screw x2
101035
M8x12xT0.2mm x2
101035
116006R
Ball Bearing 8x16x5mm (Red Rubber Case) x2
104016
M4x2.5mm Set Screw x2
s
will engage later
r.
Note:
By tightening the screws, the 2 speed clutch will engage
later, while loosening the screws will make the 2 speed
clutch engage earlier.
Initial setup
15.5mm
2.0 Hex
PROTIP:
Insert your hex driver all
the way through the 2
speed shoe, then fit the
hex screw on the hex
driver and slowly turn your
hex driver upwards.
104016
330833
330833

9
5
BAG D
104010
101018
106019R
106019R
228001(#8 #9 #10)
338011
108001
M3x12mm FH/ST HEX Screw x4
338023
2503261A
228001(#8 #9 #10)
338059
2503261A
104010
M5x4mm Set Screw (Flat Bottom) x1
Pro Tip:
Before installing the M5x4 set screw (104010),
remember to clean the set screw and center driver joint (330661A) rst.
Then apply TLC on the set screw.
Note:
The aluminum front lower arm holder (338059) can o󰀨er 0° or 1°
kick-up for your front lower suspension.
You may use the inserts 228001(#10)
kick-up or 228001(#9) to get 1° for your front lower suspension.
Note:
101018SHIM 13x16x0.2mm
Please use 13x16x0.2mm shims to adjust the play between the crown gear and pinion gear.
Standard suggestion is 1pc shim on the di󰀨 crown gear side and 3 pcs on the other side.
116019R
Ball Bearing 5x13x4mm (Red Rubber Case) x2
338011
S35 series Pinion Gear Stopper (5x7x5.1mm) x1
108001
108001
101018
SHIM 13x16x0.2mm x4
330661A
101018

10
6
7
BAG E1
104010
104010
M5x4mm Set Screw (Flat Bottom) x1
116019R
Ball Bearing 5x13x4mm (Red Rubber Case) x2
Pro Tip:
Before installing the M5x4 set screw
(104010), remember to clean the set screw
and center driver joint (330661A) rst.
Then apply TLC on the set screw.
338011
S35 series Pinion Gear Stopper (5x7x5.1mm) x1
101018
SHIM 13x16x0.2mm x4
Note:
101018SHIM 13x16x0.2mm
Please use 13x16x0.2mm shims to adjust the play between the crown gear and pinion gear.
Standard suggestion is 1pc shim on the di󰀨 crown gear side and 3 pcs on the other side.
101018
2503261A
108001
106019R
106019R 330661A
338011
338023
2503261A
228001(#2 #3 #4)
228001(#2 #3 #4)
338082
108001
330134
330136
2501121C
106005
Left
Right
228005H-F
106021A
228005H-F
101018
106005
M3x15mm Hex Socket OH/TP Screw x2
106021A
M4x10mm Hex Socket OH/TP Screw X2
108001
M3x12mm FH/ST HEX Screw x4

11
BAG E1 8
9
101020A
104004
104004
338058
228001(#5 #6 #7)
338056
104004
M3x3mm Set Screw x2
2503261A
Pop in the Stabilizer Guide.
108008
108008
M3x35mm FH/ST HEX Screw x2
101020A
3mm Countersunk Washers (GM) x2
228001(#5 #6 #7)
115008A (2.3mm)
or
115035A (2.2mm)
338056
S35-4 Series Lower Arm Hinge Pin (68.5mm) x2

12
11
10
BAG E1
104005
M3x4mm Set Screw x2
108003
M3x10mm FH/ST HEX Screw x
108006
338057
340017
108006
108003
Note:
The aluminum front upper arm holder (338057) can o󰀨er either
0° or + -1° kick-up for your front upper arm suspension.
You may use the inserts 228001(#13) to get 0° kick-up
or 228001(#12) to get +-1° for your front upper suspension.
108006
M3x8mm FH/ST HEX Screw x2
2
106013
M2.5x8mmH ex Socket OH/TPScrew
x
2
106013
104005
228001(#11 #12 #13)

13
12
13
BAG E1
14
228001(#14 #15 #16)
330119
Front Upper Arm HingPin x2
338081
228009
228009
106015
106015
330119
330119
108001
108001
Note:
2503260-1
S35-3 Front Upper Arm Adjust Insert (0.9mm)
2503260-2
S35-3 Front Upper Arm Adjust Insert (1.0mm)
2503260-3
S35-3 Front Upper Arm Adjust Insert (1.1mm)
2503260-4
S35-3 Front Upper Arm Adjust Insert (2.0mm)
106015
M3x5mm Hex Socket OH/TP Screw x2
106005
M3x15mm Hex Socket OH/TP Screw x2
330134
330136
2501121C
106021A
106005
228005H-R
330399B
108005
108001
338083
108005
M3x14mm FH/ST HEX Screw x2
108001
M3x12mm FH/ST HEX Screw x2
108001
M3x12mm FH/ST HEX Screw x2
106021A
M4x10mm Hex Socket OH/TP Screw X2
PRO TIP:
The S35-GT2/2e Front Upper Arm Adjust Inserts
can give di󰀨erent steering adjustments (Ackerman).
Put all inserts behind the front upper arms, you will get faster steering response.
Otherwise put all inserts in front of the upper arms,
you will get more stable steering response.
Try to use 2503260-1 or 2503260-3 to adjust the front upper arm position.
2503260
(#1 #2 #3 #4)
2503260(#1 #2 #3 #4)
228001(#14 #15 #16)
106020
106020
340027-10
228009
106020
M2.5x5mm Hex Socket OH/TP Screw x10

14
16
15
108008
M3x35mm FH/ST HEX Screw x2
338056
338056
330770
108008
2503261A
104004
104004
Pop in the Stabilizer Guide.
104004
M3x3mm Set Screw x2
115005 (2.8mm)
or
115006 (2.6mm)
PRO TIP:
The S35-GT2/2e Aluminum Rear Lower Fully
Adjustable Toe-In Block (330770) can use 3
types of square inserts to get 1.0/2.0/3.0 3
different toe in angles. Also plus 3 different
rear lower arm kick up degrees.
OPTION:
228001-2 S35-4 Series Rear Lower Arm Holder Square Insert (+1/+1)
228001-3 S35-4 Series Rear Lower Arm Holder Square Insert (0/+1)
228001-4 S35-4 Series Rear Lower Arm Holder Square Insert (0)
228001(#2 #3 #4)
228001(#2 #3 #4)
338056
S35-4 Series Lower Arm Hinge Pin (68.5mm) x2

15
17
BAG E2
104005
106013
104005
106013
104005
M3x4mm Set Screw x2
18
117003
117003
117003
101021
117003
101021
103001
2501122B
103001
106007
338043
330114A
610019
115004A
116004R
116004R
106014
2501122B
338052
338053
103001
M3 Nut Lock x2
117003
Flange Ball Bearing 3x6x2.5mm x4
106007
M3x12mm Hex Socket x2
OH/TP Screw(HT)
116004R
Ball Bearing 6x10x3mm (Red Rubber Case) x2
101021
M3x8xT1mm x2
106014
M2x6mm Hex Socket OH/TP Screw x1
106013
M2.5x8mm Hex Socket OH/TP Screw x2

16
20
19
BAG E3
101019
SHIM 6.0x10.0x0.2mm x1
108003
M3x10mm FH/ST HEX Screw x2
108003
108003
116004R
101019
338048
2503260-04
2503264A
2503260-04
330118A
338051
330118A
330252
330252
Screw and adjust 330118A Knuckle
Pivot Ball Nut so as the pivot ball can
be moved smoothly.
106002
Left
Right
106002
M3x10mm Hex Socket OH/TP Screw x4
116004R
Ball Bearing 6x10x3mm (Red Rubber Case) x2

17
BAG E3 21
22
210046
101018
338080
116006R
116006R
Left
Right
210046
340026
340026
228009
116006R
116006R
330124
228002
101018
330124
104010
Left
Right
330124
Pin M3.0x16.8mm x2
330124
Pin M3.0x16.8mm x2
116006R
Ball Bearing 8x16x5mm (Red Rubber Case) x4
101018
SHIM 13x16x0.2mm x2
101018
SHIM 13x16x0.2mm x2
Note:
101018SHIM 13x16x0.2mm
Please use 13x16x0.2mm shims to adjust the
gap between the wheel hub and wheel knuckles.
Standard suggestion is 1pc shim on the outside
between 8x16x5mm ball bearing and knuckle.
If the wheel hub still has big play with knuckle,
please try to put another shim in another side
between ball bearing and knuckle.
Note:
101018SHIM 13x16x0.2mm
Please use 13x16x0.2mm shims to adjust the
gap between the wheel hub and wheel knuckles.
Standard suggestion is 1pc shim on the outside
between 8x16x5mm ball bearing and knuckle.
If the wheel hub still has big play with knuckle,
please try to put another shim in another side
between ball bearing and knuckle.
104010
M5x4mm Set Screw (Flat Bottom) x2
106001
M3x10mm Hex Soket OH/TP Screw x8
106009
M3x25mm Hex Soket OH/TP Screw x4
104010
228001
(#17 #18)
228001(#17 #18)
106001
103001
106001 106009
338080
103001
M3 Nut Lock x4
116006R
Ball Bearing 8x16x5mm (Red Rubber Case) x4
104010
M5x4mm Set Screw (Flat Bottom) x2

18
24
23
BAG E3
103001
103001
330782
330782
330782
Rear Hub Carriers Hing Pin with Nut x2
103001
M3 Nut Lock x2
2503260
(#5 #6 #7)
2503260
(#5 #6 #7)
2503260 (#5 #6 #7)
330117A
330117A

19
25
26
BAG E3
330777A
330123A
Rear Upper Sus. Arm Turnbuckles x2
228006-5
228006-5
338070
330123A
104009
106002
101026
22.1mm
106002
M3x10mm Hex Soket OH/TP Screw x2
104009
M3x16mm Set Screw x2
101026
S102 Aluminum Washer 3X6X1.5mm x2
50%
8mm
NOTE:

20
27
28
BAG F
106022
106022
106010
106009
103001
103001
220016
220016
103001
103001
106010
220017
220017
220017
220017
220015
106006
106006
106006
M3x20mm Hex Soket OH/TP Screw x2
106003
M3x16mm Hex Soket OH/TP Screw x2
1
1
1
2
2
103001
M3 Nut Lock
x2
103001
M3 Nut Lock
x2
106009
M3x25mm Hex Soket OH/TP Screw x2
106010
M3x6mm Hex Soket OH/TP Screw x2
106022
M2.5x14mm Hex Soket OH/TP Screw x2
106003