Target Siebert 4 shelf bookcase User manual

siebert
4 shelf bookcase
assembly instructions
style # TGBNT4BKBK (black & walnut)
dpci # 249-14-5153
tcin # 53536358
style # TGBNT4BKWH (whitewashed oak & gray)
dpci # 249-14-5154
tcin # 53536359
>>
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-17
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

hardware
(H1) x 32
wooden dowel
(H2) x 26
cam bolt
(H3) x 26
cam
(H4) x 32
short pan head screw
(H5) x 1
knob
(H6) x 1
knob bolt
(H7) x 1
wall strap
(H8) x 2
washer
(H9) x 1
wall anchor
(H10) x 1
wall screw
(H11) x 1
long pan head screw
(H12) x 6
cam cover
4

exploded diagram
ITEM DESCRIPTION QUANTITY
1 left side panel 1
2 right side panel 1
3 partition 3
4shelf A 1
5 shelf B 1
6 shelf C 1
7 shelf D 1
8 shelf E 1
9 door 1
10 back panel 2
5

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
6
1. 2. 3.
4. 5.

7
step 1: attach shelf A and B to partition
(H1) x 4
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam
1.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush.
1.3. Refer to page 6 for instructions on how to use the cam lock system.
1.4. Do not over tighten bolts.

8
step 2: attach shelf B and C to partition
(H1) x 4
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam
2.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2.2. Screw-In cam bolts must be screwed down ush.
2.3. Refer to page 6 for instructions on how to use the cam lock system.
2.4. Do not over tighten bolts.

step 3: attach left side panel
(H1) x 6
wooden dowel
(H2) x 10
cam bolt
(H3) x 6
cam
3.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
3.2. Screw-In cam bolts must be screwed down ush.
3.3. Refer to page 6 for instructions on how to use the cam lock system.
3.4. Do not over tighten bolts.
9
(H1) x 6
wooden dowel
(H2) x 10
cam bolt
(H3) x 6
cam

10
step 4: attach shelf D and E to partition
(H1) x 4
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam
4.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
4.2. Screw-In cam bolts must be screwed down ush.
4.3. Refer to page 6 for instructions on how to use the cam lock system.
4.4. Do not over tighten bolts.

11
step 5: attach shelf D/shelf E/partition to left side panel
(H1) x 4
wooden dowel
(H3) x 4
cam
5.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
5.2. Screw-In cam bolts must be screwed down ush.
5.3. Refer to page 6 for instructions on how to use the cam lock system.
5.4. Do not over tighten bolts.

12
step 6: slide in door

step 7: attach right side panel
(H1) x 10
wooden dowel
(H2) x 10
cam bolt
(H3) x 10
cam
7.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
7.2. Screw-In cam bolts must be screwed down ush.
7.3. Refer to page 6 for instructions on how to use the cam lock system.
7.4. Do not over tighten bolts.
13
(H1) x 10
wooden dowel
(H2) x 10
cam bolt
(H3) x 10
cam

step 8: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H4) x 32
short pan head
screw
8.1. Make sure the screws go through the pre-drilled holes properly.
8.2. Do not over tighten screws.
14
hole for anti-tip
pre-drilled holes
Make sure the screws go through the pre-drilled holes properly.

15
step 9: attach door knob
(H5) x 1
knob
(H6) x 1
knob bolt
9.1. Do not over tighten bolts.

step 10: attach cam covers
(H12) x 6
cam cover
10.1. Place cam covers over any visible holes on the bookcase.
16
Place cam covers over any visible holes on the bookcase.

step 11: install anti-tip kit
(H11) x 1
long pan head
screw
(H7) x 1
wall strap
(H9) x 1
wall anchor
(H10) x 1
wall screw
(H8) x 2
washer
Position against wall
Mark position of strap hole on wall
Drill 1/4” hole
Tap in wall anchor
Fasten anti-tip strap with wall screw
provided
17
(H7)
(H11)
(H8)
(H10)
(H9)
(H8)
Mark position of strap hole on wall
Fasten anti-tip strap with wall screw
provided
(H10)
(H9)
(H8)
Position against wall
Drill 1/4” hole
Tap in wall anchor

WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items
in the lowest drawers.
• Do not set TV's or other heavy objects
on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang
on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system .
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.
1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in
excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury.
2. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.
18
40 lbs.
40 lbs. per shelf
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.

© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.