Target Project 62 T80526-4 User manual

>> Assembly instructions
TM
ADA Mixed Material End Table with Glass Top
Style # T80526-4
DPC-item # 249-17-3057

Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Good luck – though we’re confident you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a work surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
2
tool needed (only hex wrench included)

table of contents
3
Questions? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and article number ready when calling.
Introduction 2
Hardware 4
Parts list 5
Assembly 6-12
Care and maintenance and warranty 13
Important safety information 14

4
hardware
(H1) x 16
1/4” x 13 mm bolt
(H3) x 4
bumper
(H2) x 4
M4 x 30 mm screw
(H4) x 1
hex wrench
Spare hardware

ITEM DESCRIPTION QUANTITY
ATop glass 1
BSide frame 2
CTop stretcher 2
DBottom stretcher 2
EDrawer box support 2
FDrawer box 1
5
B
C
D
E
A
F
E
C
D
B

6
step 1.
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
Align and attach the two top stretchers (C) to the top of one side frame (B).
(H1) x 2
1/4” x 13 mm bolt
(H4) x 1
Hex wrench
B
B
C
C
C
B
H1
H1
H1
C
C
C

7
step 2.
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
Fasten the two drawer box supports (E) to the middle rail of side frame (B).
(H1) x 4
1/4” x 13 mm bolt
(H4) x 1
Hex wrench
B
H1
E
E
H1
E
B

8
step 3.
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
Place the drawer box (F) between the top stretchers (C) and drawer box supports (E).
Align and attach the bottom stretchers (D) to the side frame (B).
(H1) x 2
1/4” x 13 mm bolt
(H4) x 1
Hex wrench
C
C
F
E
E
D
D
B
The drawer front faces up
H1
The screw head will
face the floor when the
unit is turned upright.
D
D
B
B

9
step 4.
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
Repeat the same procedure to attach the other side frame (B) at opposite end.
(H1) x 8
1/4” x 13 mm bolt
(H4) x 1
Hex wrench
H1
H1
D
B
E
C
C
H1
E
D
H1
BB
C
C
BE
B
B
D
D

10
step 5.
Firmly press the drawer box (F) against the drawer box supports (E). Make sure that the mounting holes overlap the pilot holes underneath the drawer box (F)
properly.
Fasten the drawer box (F) to the drawer box supports (E).
(H2) x 4
M4 x 30 mm screw
E
E
F
H2
E