Target Warwick FKWWCB3DWH User manual

warwick
media cabinet
assembly instructions
style # FKWWCB3DWH (white)
dpci # 249-10-2303
tcin # 54187445
style # FKWWCB3DBR (fawn brown)
dpci # 249-10-1555
tcin # 52166635
>>
© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
assembly 6-14
how to adjust door alignment 15
how to adjust the door hinges 17
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 20
wooden dowel
(H2) x 12
bolt
(H3) x 12
lock washer
(H4) x 19
pan head screw
(H5) x 6
pull bolt
(H6) x 3
pull
(H7) x 12
shelf support
(H8) x 4
large truss head screw
(H9) x 1
allen wrench
(H10) x 4
side hinge
(H11) x 2
middle hinge
(H12) x 2
large at head screw
(H13) x 24
small at head screw
(H14) x 1
wall anchor
(H15) x 1
wall screw
(H16) x 1
small truss head screw
(H17) x 1
wall strap
(H18) x 14
washer

5
exploded diagram
ITEM DESCRIPTION QUANTITY
A top panel 1
B left side frame 1
C right side frame 1
D bottom panel 1
E bottom rail 1
F left partition 1
G right partition 1
H back panel 1
I outer shelf 2
J inner shelf 1
K door 3

6
step 1. attach left and right partition panels with top panel
(H1) x 4
wooden dowel
(H2) x 4
bolt
(H3) x 4
lock washer
(H18) x 4
washer
(H9) x 1
allen key
1.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
1.2. Align bolts with pre-drilled holes.
1.3. Do not over tighten bolts.
nished edge
notched edge

77
step 2. attach bottom panel
(H1) x 4
wooden dowel
(H8) x 4
large truss
head screw
2.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2.2. Align screws with pre-drilled holes.
2.3. Do not over tighten screws..
notched edge

8
step 3. attach side frames
(H1) x 12
wooden dowel
(H2) x 8
bolt
(H3) x 8
lock washer
(H18) x 8
washer
(H9) x 1
allen key
3.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
3.2. Align bolts with pre-drilled holes.
3.3. Do not over tighten bolts.

9
step 4. attach bottom rail
(H12) x 2
large at
head screw
4.1. Align screws with pre-drilled holes.
4.2. Do not over tighten screws.

10
step 5: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H4) x 19
pan head screw
5.1. Make sure the screws go through the pre-drilled holes properly.
5.2. Do not over tighten screws.
hole for anti-tip