Target 9-Cube User manual

>> assembly instructions
9-Cube
style dpci nish
58020 002-11-0590 White
58023 002-11-0588 Espresso

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room
in no time. Good luck—though we’re condent you won’t need it.
tools needed
before you begin
1. Check for damaged or missing parts. Call 1-800-874-0008 to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.

3
introduction 2
hardware 4
parts list 5
safety precautions 6
helpful hints 7
installing L-bracket 8
assembly 9-18
table of contents
QUESTIONS? Just call 1-800-874-0008 for parts and service. For faster service, have the style number and DPCI number ready when calling.

4
hardware
(H5) x 10
short dowel
(H1) x 20
assembly screw
#10 x 1-1/2 in. athead
(H2) x 20
screw cover
(H9) x 1
L-bracket
(H7) x 1
L-bracket screw
#10 x 1/2 in. athead
(H8) x 1
wall screw
#10 x 1-1/2 in.
(H3) x 2
hole plug
(H6) x 60
nail
(H4) x 8
long dowel

5
A
A
B
B
C
C
DD
D
D
D
D
E
E
ITEM DESCRIPTION QUANTITY
A side panel 2
Btop/bottom panel 2
Chorizontal divider 2
D vertical divider 6
Eback panel 5

6
• This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or
serious injury could occur.
• Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse.
Serious bodily injury and/or damage to personal belongings may occur.
• Do not overload unit. If any shelf, top, or bottom of unit bows or bends greater than 1/2 in., it is overloaded. The shelf, top, or bottom could
collapse and cause serious bodily injury and/or damage to personal belongings.
• Do not climb or step on the unit. This is not a bench. The unit may become unstable and either tip or collapse. Serious bodily injury and/or
damage to personal belongings may occur.
• Do not use this unit as a television stand. Serious bodily injury and/or damage to personal belongings may occur.
• Do not mount or attach anything to the sides, rear or front of the unit as this can create a force which can cause the unit to tip. Serious bodily
injury and/or damage to personal belongings may occur.
• Do not stack units in a vertical format. Stacking of units can cause an unsafe tip-over hazard which may cause serious bodily injury and/or
damage to personal belongings.
• Do not hang this unit on the wall. The product structure is not designed for wall hanging. Serious bodily injury, damage to personal belongings,
and/or damage to the wall may occur.
• All units must be secured individually to wall stud using L-Bracket and Wall Screw (#10 x 1-1/2 in.) provided. If wall stud is not accessible,
consult your local hardware store for appropriate mounting hardware. Failure to do so may create an unsafe tipping hazard that could lead to
serious bodily injury and/or damage to personal belongings.
• We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood oors, etc.
safety precautions
warning

7
We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood oors, etc.
helpful hints
Unfinished edges are shaded in gray. It is important to understand how finished edges go together. Take a moment to lay out all
the wood pieces and note the finished and unfinished (raw wood) edges. Arrange pieces so all finished edges are facing the same
way. While assembling, take care to note in each diagram which way finished edges are facing. In general, all finished edges will
face forward and all finished sides (large area of piece) will face up when product is fully assembled and upright.
hand tighten screws
We recommend you hand-tighten screws. Use care not to overtighten if using power tools.
unfinished edgefinished edge

8
There are several "key points" to
L-bracket installation. Please review the
drawings and comments at right as well
as the assembly steps provided.
All units must be fastened to the wall.
Always mount L-bracket to a wall-stud.
installing L-bracket
short
end
long
end
wall
stud
Install short end against wall/wall
stud; long end against unit.
Do not install this unit ush against the
wall! This unit requires a gap of between
1/2 inch and 1 inch to install properly.
For more hidden hardware, secure L-bracket
under top panel. See step 10 for detailed
installation instructions.
Max.
1 in.
Min.
1/2 in.
wall
stud
top panel
wall
stud
Serious or fatal crushing injuries can occur
from furniture tip-over.
To help prevent tip-over:
- Install tip-over restraint provided.
- Unless specically designed to
accommodate, do not set TVs or other
heavy objects on top of this product.
- Never allow children to climb or hang on
drawers, doors, or shelves.
- Place heavy items on lower shelves and as
far back as possible.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove.
WARNING

9
1. Push 4 short dowels into holes of one xed shelf.
2. Install dowels only into one top/bottom panel (both top/bottom panels are the same.)
3. Top/Bottom panels have six holes on one side with the middle holes going through to the other side.
4. Unnished edges are shaded in light gray.
B
step 1.
(H5) x 4
short dowel

10
1. Attach xed shelf to one side panel.
2. Make sure nished edges of unit are up.
A
B
step 2.
(H1) x 2
assembly screw
#10 x 1-1/2 in. athead