TCS AMI Series User manual

TCS TürControlSysteme AG, TCS Hotline Germany: [e-mail] Subject to technical changes.
Fax: [phone] / 9 88 129 PI_AMI_FG-DISPLAY-uk 2A
Product information
Series AMI
Front-door stations with display module
AMI10105
AMI10200
AMI10300
AMI10400
Note on the validity of this product information
This product information states specific information on the modules.
It is only valid in combination with the enclosed product information Modules of the series
AMI in front-door stations.

2 05/2013
TCS TürControlSysteme AG, TCS Hotline Germany : [e-mail] Subject to technical changes.
Fax: [phone] / 9 88 129 PI_AMI_FG-DISPLAY-uk 2A
Table of contents
Note on the validity of this product information.................................................................1
Table of contents...............................................................................................................2
Scope of delivery...............................................................................................................3
Module descriptions..........................................................................................................4
Loudspeaker module AMI10200 ......................................................................................4
Display module LCD graphic AMI1010x...........................................................................5
Keypad module AMI10300 Jogwheel AMI10400 ...........................................................7
Installation..........................................................................................................................8
Install the display module into the front panel ..................................................................8
Remove the display unit from the module plate............................................................8
Install the module plate and display unit in the front panel ...........................................8
Connect the lines...............................................................................................................9
Internal connection of modules within the front-door station ............................................9
placement example for keypad module........................................................................9
placement example for jogwheel module......................................................................9
Wiring example...............................................................................................................10
Connection diagram.......................................................................................................10
Commissioning................................................................................................................11
Note on connecting the PS/2 keypad to the display module ..........................................11
Commissioning of a front-door station with display module............................................11
Configuration ...................................................................................................................12
Factory settings..............................................................................................................12
Configuration options .....................................................................................................12
Display module AMI1010x..........................................................................................12
Settings.............................................................................................................................12
Operation of the front-door station................................................................................13
Calling a resident............................................................................................................13
... via selecting the initial letter....................................................................................13
... via selection in the resident list...............................................................................14
... by entering the flat number.....................................................................................15
Voice connection............................................................................................................15
Door release via codelock (only for front-door stations with keypad module).................16
Repair................................................................................................................................17
Display module AMI1010x: Replace the EEPROM storage...........................................17
Observe when transfer data from a previous version.....................................................17
Accessory.........................................................................................................................18
Notes.................................................................................................................................19
Service..............................................................................................................................20

05/2013 3
TCS TürControlSysteme AG, TCS Hotline Germany: [e-mail] Subject to technical changes.
Fax: [phone] / 9 88 129 PI_AMI_FG-DISPLAY-uk 2A
Scope of delivery
Scope of delivery
Delivery item
Module combination LCD display and
loudspeaker module AMI10105-07xx*
keypad module
AMI10300
jogwheel module
AMI10400
display
module
loudspeaker
module
4 x locking nut M4




3 x spacer foil 0.5 mm




allen key 2.5 mm

screwdriver with round
handle

programming manual
Functional group with
display module
AMI1010x

product information
Modules of the series
AMI in front-door sta-
tions




product information
Functional group with
display module

* Display module and loudspeaker module are delivered together as module combination LCD display and
loudspeaker module AMI10105-0757 or AMI10105-0710
!
To set and programme the display modules, you need exclusively a PS/2 keypad
(not enclosed in the delivery, see Accessory, page 18)!
It is not possible to use a PC keypad with USB connection or a USB adapter!

4 05/2013
TCS TürControlSysteme AG, TCS Hotline Germany : [e-mail] Subject to technical changes.
Fax: [phone] / 9 88 129 PI_AMI_FG-DISPLAY-uk 2A
Module descriptions
A front-door station with display module for up to 1000 flats consists of:
a module combination LCD display and loudspeaker module
and keypad or jogwheel module
Loudspeaker module AMI10200
Overview
1 microphone
2 cover PS/2 socket
Loosen the cover with allen
key of 3 mm (not included in
the delivery).
Connect PS/2 keypad.
3 connection cable micropho-
ne
4 connection cable PS/2 key-
pad / jogwheel module
5 connection cable loudspea-
ker
Technical data
housing
aluminium anodised
H x W x D
105 x 105 x 27 mm
weight
235 g
1
2
3
4
5

05/2013 5
TCS TürControlSysteme AG, TCS Hotline Germany: [e-mail] Subject to technical changes.
Fax: [phone] / 9 88 129 PI_AMI_FG-DISPLAY-uk 2A
Display module LCD graphic
Overview
1 LC display
2 connection cable
keypad module
3 connection of micro-
phone
4 connection of jogwheel
module or PS/2 keypad
5 EEPROM
6 connection of Service
Device TCSK-01
7 connection of
TCS-BUS®, pluggable
screw terminal
8 connection of
loudspeaker
9 matching resistor-
for RS485
10 RS485
11 USB Typ B 1.1 / 2.0
Technical data
display
160 x 160 pixel, white-blue
module plate
glass inserts
housing display unit
aluminium anodised
polycarbonate PC-AR
steel zink-coated
H x W x D
131 x 111 x 45 mm
weight
560 g
acceptable ambient temperature
−20 °C to +50 °C
input current standby
max. input current
I(a) = 0.4 mA, I(P) = 140 mA
I(Pmax) = 245 mA
RS485 interface
matching resistor
transmission
120 Ohm (plugged ex works)
half duplex (2-wire connection and 1 x ground with
option for jumper),
recommended baud rate: 9600 baud
can be used with ADx configurator,
use only RS485-PC interface with galvanic isolation!
3-wire technique necessary!
1
2
3
4
5
6
7
11
10
9
8

6 05/2013
TCS TürControlSysteme AG, TCS Hotline Germany : [e-mail] Subject to technical changes.
Fax: [phone] / 9 88 129 PI_AMI_FG-DISPLAY-uk 2A
Short description
Display module for front-door stations in individualised assembly
for up to 1000 flats
LC display, 160 x 160 pixel with white-blue backlight
code lock function (number of codes: 3)
call destination selection via an alphabetically sorted resident list or by entering the tar-
get number (flat number) as quick selection
adjustable (rotation) direction in the name list, name list as of 6 data sets endless
name pre-selection can be realised via the initial letter
start screen can be configured by a qualified electrician
multi-lingual user guidance (can be programmed during the installation: German,
English, French, Danish, Dutch, Turkish, Serbian, Italian, Spanish, Portuguese,
Swedish, Slovak, Slovene, Czeck)
indication of date and time
automatic switch-over between summer and winter time
optionally outdoor temperature indication (temperature sensor FBS2100-0600 not in-
cluded in the delivery, see Accessory, page 18)
import function for old databases of predecessors
acknowledgement tone when pressing the bell button
acknowledgement tone for the start of the voice connection
output of voice messages for user guidance
communication time ex works: 56 seconds / can be adjusted with PS/2 kexpad (not in-
cluded in the delivery, see Accessory, page 18) or ADx configurator (part of the mainte-
nance package FBI1210-0; not included in the delivery, see Accessory, page 18)
S-terminal to trigger door release, light switch, control or door call function (max. length
of the entrance connection line: 2 m)
R-terminal to connect an extended function –door release
per resident dataset, 2 serial numbers can be stored
can be adjusted with PS/2 keypad or ADx configurator:
door release time at R-terminal ex works: 3 seconds /
door release in door standby time /
door standby time (to control the short-term memory in indoor stations) ex works: 56
seconds /
voice connection in door standby time /
resident dataset and parameter
!
Attention when using the display module!
The display module is permitted exclusively for safety extra low voltage (SELV) and
protective extra low voltage (PELV).
Avoid direct solar radiation (ambient temperature max. +50 °C)!
Direct solar radiation reduces the durability of the liquid crystals in the display.

05/2013 7
TCS TürControlSysteme AG, TCS Hotline Germany: [e-mail] Subject to technical changes.
Fax: [phone] / 9 88 129 PI_AMI_FG-DISPLAY-uk 2A
Keypad module AMI10300 Jogwheel AMI10400
Overview Overview
1 number keys
0 … 9
Call a resident by entering the flat
number.
Enter the number when using the
codelock function.
2 ABC button
Open the residents list sorted by
initial letter. Confirm the selected
letter.
ABC button calls up the help
menu when in start screen.
3 navigation buttons
UP / DOWN
Browse within the resident list or
in the menu.
4 bell button
Call a resident.
5 OK button
Confirm the entry /
the menu request.
6 C button
Code lock function:
Enter the access code
7 jogwheel
Selection help menu /
resident list.
Turn to get into the help menu,
turn further to get to the resident
list.
8 connection cable keypad mod-
ule
9 PS/2 connection (IN) loud-
speaker- / jogwheel module
10 PS/2 connection (MAIN)
display / jogwheel module
Technical data
keypad module
jogwheel module
housing
aluminium anodised
aluminium anodised
H x W x D
105 x 105 x 15 mm
105 x 105 x 52 mm
weight
130 g
265 g
Short description
Keypad or jogwheel module for front-door stations in individualised assembly
keypad with 16 buttons to select the name (call destination) and for using the code lock
function (number of codes: 3)
jogwheel to select the name (call destination)
8
7
4
2
9
10
1
2
3
5
6
4

8 05/2013
TCS TürControlSysteme AG, TCS Hotline Germany : [e-mail] Subject to technical changes.
Fax: [phone] / 9 88 129 PI_AMI_FG-DISPLAY-uk 2A
Installation
Install the display module into the front panel
Remove the display unit from the module plate
Loosen the 4 x panhead screws (1)
with the enclosed allen key 2.5 mm.
Pull off the display unit from the module
plate (2).
Install the module plate and display unit in the front panel
Put the module plate (2) onto the front
panel (3) and fix it with the enclosed 4 x
fastening nuts M4 (4).
Note: The sealing strip (5) which sticks
to the module plate must face upwards!
Put the display unit onto the module
plate
and fix it with the 4 x panhead screws
(1).
Note: The orientation arrow (6)
on the type lable must face upwards!
Dismounting has to be realised in re-
verse order!
6
1
3
2
4
4
2
1
5

05/2013 9
TCS TürControlSysteme AG, TCS Hotline Germany: [e-mail] Subject to technical changes.
Fax: [phone] / 9 88 129 PI_AMI_FG-DISPLAY-uk 2A
Connect the lines
Internal connection of modules within the front-door station
After the installation within the front panel, the modules themselves have to be wired.
placement example for keypad module
placement example for jogwheel module
1connection cable loudspeaker module / microphone
1connection cable loudspeaker module / microphone
2connection cable loudspeaker module / loudspeaker
2connection cable loudspeaker module / loudspeaker
3 connection cable keypad / display module
3PS/2 connection cable jogwheel / loudspeaker module
4PS/2 connection cable jogwheel / display module
AMI10200
AMI10200
AMI1010x
AMI10300
3
1
1
2
AMI1010x
AMI10400
1
2
3
4

10 05/2013
TCS TürControlSysteme AG, TCS Hotline Germany : [e-mail] Subject to technical changes.
Fax: [phone] / 9 88 129 PI_AMI_FG-DISPLAY-uk 2A
Wiring example
Connection diagram
Note on the FBS2100:
Optionally available: the temperature sensor to indicate the temperature in the
display (not included in the delivery, see Accessory, page 18).
ISH3030
ISH3030
front-door station
floor push
button
floor push
button
Front-door station