TCS PDS Series User manual

Product information
Front-door station series
for surface-mounting
Profi-Economic PES Profi-Design PDS
TCS TürControlSysteme AG •Geschwister-Scholl-Str. 7 •39307 Genthin Subject to change without notice.
Phone: +49 39 33 / 87 99 10 •Fax: +49 39 33 / 87 99 11 •www.tcs-germany.com Art.Nr. 0015689 Version 1.0 mi

PI_GB_PES_PDS_Art0015689_1v0.doc 2 10/2005
In Table of contents
Scope of delivery .................................................................................................................3
Safety notices ......................................................................................................................3
General notes on the cabling in TCS audio systems ...........................................................4
Device overview...................................................................................................................5
Technical data .....................................................................................................................5
Application ...........................................................................................................................6
Brief description ...................................................................................................................6
Basic functions .................................................................................................................6
Additional functions ..........................................................................................................6
Assembly .............................................................................................................................7
Cable connection .................................................................................................................8
General notes...................................................................................................................8
Connection .......................................................................................................................8
2-wire special mode .........................................................................................................8
Wiring example.................................................................................................................8
Commissioning ....................................................................................................................9
Microphone and loudspeaker volume setup ........................................................................9
Nameplate labelling .............................................................................................................9
Programming of bell buttons ..............................................................................................10
Basic principle ................................................................................................................10
Programming with the Service Device............................................................................10
Programming steps legend ............................................................................................10
Programming state of a bell button ....................................................................................11
Testing ...........................................................................................................................11
Deleting the programming ..............................................................................................11
Programming a bell button.................................................................................................12
Method 1: In-house station not accessible .....................................................................12
Programming the other bell buttons:...........................................................................12
Method 2: In-house station accessible ...........................................................................13
Programming the other bell buttons:...........................................................................13
Programming an already programmed bell button.............................................................14
Basic principle ................................................................................................................14
Method 1: In-house station not accessible .....................................................................14
Programming the other already programmed bell buttons..........................................14
Method 2: In-house station accessible ...........................................................................15
Programming the other already programmed bell buttons..........................................15
Note................................................................................................................................15
Repair ................................................................................................................................16
Replacing the EEPROM memory...................................................................................16
Cleaning.............................................................................................................................16
Service...............................................................................................................................16
TCS TürControlSysteme AG •Geschwister-Scholl-Str. 7 •39307 Genthin Subject to change without notice.
Phone: +49 39 33 / 87 99 10 •Fax: +49 39 33 / 87 99 11 •www.tcs-germany.com Art.Nr. 0015689 Version 1.0 mi

PI_GB_PES_PDS_Art0015689_1v0.doc 3 10/2005
Scope of delivery
1 x PES / PDS
1 x hexagonal angle screwdriver DIN 911
1 x screwdriver with round handle
nameplates, empty and with light symbol
product information
Safety notices
!Assembly, installation, and commissioning must only be carried out by a qualified elec-
trician!
For work on systems with 230 V AC mains current the safety requirements of DIN VDE
0100 must be observed.
When installing TCS:BUS systems the general safety rules for telecommunication systems
in accordance with VDE 0800 must be observed:
• separate cabling for high and low voltage lines,
• minimum distance of 10 cm for joint cabling arrangements,
• use of separators between high and low voltage lines in joint cable ducts,
• use of standard telecommunication cables, e. g. J-Y (St) Y with 0.8 mm² cross section,
• existing cables (rationalisation) with different cross sections may be used whilst taking
account of the loop resistance.
!Suitable lightning protection must ensure that a voltage of 32 V DC will not be ex-
ceeded at the TCS:BUS wires a and b.
TCS TürControlSysteme AG •Geschwister-Scholl-Str. 7 •39307 Genthin Subject to change without notice.
Phone: +49 39 33 / 87 99 10 •Fax: +49 39 33 / 87 99 11 •www.tcs-germany.com Art.Nr. 0015689 Version 1.0 mi

PI_GB_PES_PDS_Art0015689_1v0.doc 4 10/2005
General notes on the cabling in TCS audio systems
The cabling depends on the building situation and is only limited by its length.
• When selecting the cable length consider: the
loop resistance must not exceed max. 20 Ω(ta-
ble)
• To keep within the max. permissible loop resis-
tance the wire cross section can be doubled, i.e.
two lines are used for one wire (figure). The li-
nes must be twisted.
• When using screened cables: connect the
screens to each other and connect on one side
to earth (b wire) on the power supply unit
• Choice of line or star wiring
rt = red gn = green
bl = blue br = brown
ws = white sw = black
ge = yellow
Table: loop resistances
Cable cross section
Cable length in m 0.6 mm² 0.8 mm²
Loop resistance in Ω
10 1.22 0.69
20 2.45 1.38
30 3.67 2.07
40 4.90 2.76
50 6.12 3.44
60 7.35 4.13
70 8.57 4.82
80 9.80 5.51
90 11.02 6.20
100 12.24 6.89
150 18.37 10.33
200 24.49 13.78
250 17.22
300 20.66
TCS TürControlSysteme AG •Geschwister-Scholl-Str. 7 •39307 Genthin Subject to change without notice.
Phone: +49 39 33 / 87 99 10 •Fax: +49 39 33 / 87 99 11 •www.tcs-germany.com Art.Nr. 0015689 Version 1.0 mi

PI_GB_PES_PDS_Art0015689_1v0.doc 5 10/2005
Device overview
microphone
microphone
volume control
connection for
bell button ex-
tension
PES board
loudspeaker
bell button
loudspeaker
volume control
lower
panel
loudspeaker
cover
EEPROM
connection terminal
Jum
p
er
cable
duct
attachment
holes 1, 2
attachment
holes 3, 4
condensate
drainage
Shown is the PES12
without name plate glass
Technical data
Supply voltage: + 24 V + 8 % (via power supply and control unit)
Case: aluminium, anodised
Name plate glass: plexiglass
Operating temperature range: -20°C to 50°C
Input current: I(a) = 0.4 mA, I(P) = 16 mA standby
Maximum input current: I(Pmax) = 65 mA
TCS TürControlSysteme AG •Geschwister-Scholl-Str. 7 •39307 Genthin Subject to change without notice.
Phone: +49 39 33 / 87 99 10 •Fax: +49 39 33 / 87 99 11 •www.tcs-germany.com Art.Nr. 0015689 Version 1.0 mi

PI_GB_PES_PDS_Art0015689_1v0.doc 6 10/2005
Application
The PES / PDS are front-door stations for exterior use.
They are suitable for surface mounting.
Brief description
Basic functions
Bell buttons
• Operating a programmed bell button triggers a ringing
tone at the in-house station.
• Operating an unprogrammed bell button triggers the
light switch function in the power supply and control
unit.
• When operating a bell button an acknowledgement
tone sounds.
Saving the bell button alloca-
tions in the front-door station
All programmed data (serial numbers and parameters)
are stored in the EEPROM. If the front-door station re-
quires replacement, the EEPROM board can be removed
from the programmed front-door station and inserted into
the new front-door station of identical design.
Additional functions
Name plate illumination via LED, P-wire connection required.
connection • for Service Device
• for PES / PDS: for connection of a bell button exten-
sion PET / PDS.
Allocation of serial number to
bell buttons
2
additional switching signal use a combining device BRE2.
TCS TürControlSysteme AG •Geschwister-Scholl-Str. 7 •39307 Genthin Subject to change without notice.
Phone: +49 39 33 / 87 99 10 •Fax: +49 39 33 / 87 99 11 •www.tcs-germany.com Art.Nr. 0015689 Version 1.0 mi

PI_GB_PES_PDS_Art0015689_1v0.doc 7 10/2005
Assembly
1. Opening the case
The lower panel is attached to the aluminium
profile by two hexagon socket screws.
(1) Unscrew both screws using an Allen key
only half way:
(2) Turn the lower panel to the left, without
removing it completely.
(3) Slide the name plate glass fully down.
2. Feed the cables through the cable duct.
3. Attach the device safely to the wall from the
attachment holes (see overview) using suit-
able screws.
Take care not to pinch the cables under the
spacers on the device back.
4. Closing the housing
Slide the name plate glass upwards under
the front panel.
Turn the lower panel to the right until the re-
cess fits over the screw.
Tighten the screws.
!When sliding the name plate glass upwards take care not to damage the rubber seals
in the guide grooves.
When fitting additional devices make sure that you can slide
the name plate glass of the device downwards out of the profile. Do not fit a device
below the device.
!Never seal the device using silicon! Condensate must be allowed to drain and evapo-
rate.
TCS TürControlSysteme AG •Geschwister-Scholl-Str. 7 •39307 Genthin Subject to change without notice.
Phone: +49 39 33 / 87 99 10 •Fax: +49 39 33 / 87 99 11 •www.tcs-germany.com Art.Nr. 0015689 Version 1.0 mi

PI_GB_PES_PDS_Art0015689_1v0.doc 8 10/2005
Cable connection
General notes
!
Use the small screwdriver supplied to connect the lines and prevent damage to the
device.
Please note
• the lines should not be run in front of the LED to prevent obstruction of the name-
plate illumination
• the lines must not be squeezed below the spacers on the back of the front-station.
Connection
1. Strip the insulation from the line ends.
2. Connect the lines, depending on system type, in accordance with the connection dia-
gram.
2-wire special mode
In this mode only one front-door station can be con-
nected! A P-wire has to be made by bridging termi-
nals a and P.
Note: The front-station does not work if the bridge is connected
to b instead of a.
Wiring example
• To connect a door release relay use
the R terminal.
• A door release contact can be
connected to the S terminal. This
allows for checking whether the
triggered door is open or closed.
TCS TürControlSysteme AG •Geschwister-Scholl-Str. 7 •39307 Genthin Subject to change without notice.
Phone: +49 39 33 / 87 99 10 •Fax: +49 39 33 / 87 99 11 •www.tcs-germany.com Art.Nr. 0015689 Version 1.0 mi

PI_GB_PES_PDS_Art0015689_1v0.doc 9 10/2005
Commissioning
• Fully install the devices of the system.
• Check the a and b wires for short circuits.
• Connect the power supply and control units to the mains voltage.
Switch on the mains supply.
Microphone and loudspeaker volume setup
!For adjustments use the small screwdriver supplied!
Volume control
microphone
In-house station
volume
adjustment
loudspeaker
Front-door station
volume
adjustment
The volumes have been set to an average value
at factory. A modification may not always be
necessary.
When adjusting please note:
The amplification of loudspeaker and microphone
cannot be set independently from each other.
Too great volume will cause a feedback effect
(whistling).
Nameplate labelling
The templates are available on our website
www.tcs-germany.com \ English\ Downloads \
System and technology basics\ Product installa-
tion and use \ labelling of the nameplate
1. Enter the desired name into the template.
2. Print the name plate on the special film* and
cut it to size.
3. Loosen the pockets at the outer edge of the
name plate glass using the insertion aid sup-
plied.
4. Insert the cut plates from the side into the po-
ckets on the name plate glass.
* We recommend to print the name plates on a durable special
film. The film can be ordered directly from TCS: Writable poly-
ester film for name plates DIN A4.
TCS TürControlSysteme AG •Geschwister-Scholl-Str. 7 •39307 Genthin Subject to change without notice.
Phone: +49 39 33 / 87 99 10 •Fax: +49 39 33 / 87 99 11 •www.tcs-germany.com Art.Nr. 0015689 Version 1.0 mi

PI_GB_PES_PDS_Art0015689_1v0.doc 10 10/2005
Programming of bell buttons
Basic principle
All devices at the TCS:BUS have a unique serial number. During programming this serial
number is transferred to the front-door station and linked to the bell button.
Programming with the Service Device
Utilise the simple 1 person programming with the TCS Service Device. You will not need
access to the in-house stations in the flats. The voltage supply is provided by connecting
the Service Device to the TCS:BUS. For more on the TCS Service Sevice see: www.tcs-
germany.de
If you do not have the Service Device, you can also program manually.
Programming steps legend
briefly press key LED flashes slowly
press key until
LED flashes rapidly
release key
ring tone
NoProg tone
continue
wait until Prog2 tone
Delation tone Progsperr tone
TCS TürControlSysteme AG •Geschwister-Scholl-Str. 7 •39307 Genthin Subject to change without notice.
Phone: +49 39 33 / 87 99 10 •Fax: +49 39 33 / 87 99 11 •www.tcs-germany.com Art.Nr. 0015689 Version 1.0 mi