Teknik Elstree 5426908 User manual

Elstree 2 Drawer Lateral Filer
Model 5426908
Congratulations. You
are now an adult.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4-5
6-29
30-34
35-39
40-42
43
Adjustable Wrench
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
D550 RIGHT DRAWER SIDE (2)
D551 LEFT DRAWER SIDE (2)
D552 DRAWER BACK (2)
D985 DRAWER BOTTOM (2)
E LARGE BASE (2)
F SMALL BASE (2)
G BACK (2)
H LARGE DRAWER FRONT (1)
J BALLAST (1)
K SMALL DRAWER FRONT (1)
M67 DRAWER BRACE (2)
A
B
C
D
E
F
G
H
J
K
G
E
D550
D550
D551
D551
D552
D552
D985
D985
M67
M67
Pae 3

Hardware Identification
34G INTERLOCK MECHANISM - 1 DRAWER
ACTUATOR - 2
62G
31G CORNER BRACKET - 4 LARGE FILE
BRACKET - 2
57G
FILE GLIDE - 4
4B
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 4
35MA EXTENSION SLIDE - 4 35MC 10A SLIDE CAM - 4
FILE ROD - 4
9B FILE BAR - 4
14B
SMALL FILE
BRACKET - 2
11B HIDDEN CAM - 6
1F
METAL BRACKET - 6
4G
WOOD DOWEL - 4
15F
CAM DOWEL - 6
2F 36F TWIST-LOCK®FASTENER - 12
76G L - LOCK BRACKET - 1 77G Z - LOCK BRACKET - 1 PULL - 2
189K
LOCK PACK - 1
21J
Pae 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" PAN HEAD SCREW - 3
51S
BLACK 1-1/8" PAN HEAD SCREW - 4
9S
BROWN 7/16" LARGE HEAD SCREW - 4
6S
BLACK 1/2" FLAT HEAD SCREW - 6
11S 30S BLACK 1-9/16" FLAT HEAD SCREW - 10
BLACK 9/16" LARGE HEAD SCREW - 48
1S 3S GOLD 5/16" FLAT HEAD SCREW - 16
Pae 5

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
HOW TO USE A HIDDEN CAM & CAM DOWEL 2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the ede
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
3.
Pae 6

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å To bein assembly, push four SAUDER TWIST-LOCK®
FASTENERS (36F) into the lare holes in the ENDS (A and B).
A
B
36F
Do not tihten the TWIST-LOCK® FASTENERS in this step.
Pae 7
Some assembly
(and snacks) required.

å Separate the EXTENSION SLIDES (35MC) from the EXTENSION RAILS (35MA) as shown in the upper diaram below. Be
prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (35MA) to the ENDS (A and B). Use eiht GOLD 5/16" FLAT HEAD SCREWS (3S)
throuh holes #1 and #3.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END. Turn a SCREW into
this hole.
å NOTE: The EXTENSION SLIDES (35MC) will be used later for the DRAWERS.
Step 2
A
B
Push the black lever in and pull the SLIDE from the RAIL.
35MA
35MC
3
2
1
1
2
3
GOLD 5/16" FLAT HEAD SCREW
(8 used for the RAILS)
3S
Open end
1
2
3
3
2
1
Open end
Pae 8

å Fasten the INTERLOCK MECHANISM (34G) to the RIGHT END (A).
Use three BLACK 9/16" PAN HEAD SCREWS (51S).
å Fasten the L - LOCK BRACKET (76G) to the RIGHT END (A). Use
two BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 3
A
34G
BLACK 9/16" PAN HEAD SCREW
(3 used in this step)
51S
BLACK 9/16" LARGE HEAD SCREW
(2 used in this step)
1S
Pae 9

å To bein assembly, push eiht SAUDER TWIST-LOCK®
FASTENERS (36F) into the lare holes in the BACKS (G).
Step 4
G
G
36F
Do not tihten the TWIST-LOCK® FASTENERS in this step.
36F
Pae 10