Teknik Boulevard Cafe Desk 5420701 User manual

www.teknikoffice.co.uk
Boulevard Cafe Desk
Model 5420701
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Business or pleasure.
Works both ways.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5-21
22-24
25-27
28-30
31
Skip the power trip.
This time.
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F BOTTOM (2)
G BACK (2)
H SHELF (1)
I MODESTY PANEL (1)
J DRAWER FRONT (1)
K LARGE DRAWER FRONT (2)
L RIGHT DRAWER SIDE (1)
M LEFT DRAWER SIDE (1)
N DRAWER BACK (1)
O DRAWER BOTTOM (1)
P LARGE RIGHT DRAWER SIDE (2)
Q LARGE LEFT DRAWER SIDE (2)
R LARGE DRAWER BACK (2)
S LARGE DRAWER BOTTOM (2)
A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
Q
R
F
G
I
K
P
Q
R
S
S
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
(EXTENSION SET SHOWN SEPARATED)
1EXTENSION RAIL - 6 2EXTENSION SLIDE - 6 CAM
SCREW - 12
4
HIDDEN
CAM - 12
3
L- WRENCH - 1
11
APPLIQUE
CARD - 1
9
BLACK 1-1/2" FLAT HEAD SCREW - 12
13
5FILE
GLIDE - 4 6FILE HANGER  4 7PULL  3
BLACK 1/2" PAN HEAD SCREW - 18
17
ADJUSTABLE GLIDE - 8
8
BLACK 3/8" MACHINE SCREW - 6
18
BLACK 1/2" WAFER HEAD SCREW - 4
15
BLACK 3/4" HEX HEAD SCREW - 8
14
BLACK 1/2" MACHINE SCREW - 12
16
BLACK 5/16" WAFER HEAD SCREW - 24
19
BLACK 1-5/8" WAFER HEAD SCREW - 12
12
BUMPER CARD - 1
10
Pae 4

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Fasten a BACK (G) to the RIGHT END (A) and RIGHT
UPRIGHT (C). Use eiht BLACK 5/16" WAFER HEAD
SCREWS (19).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
Pae 5
A
C
G
Some assembly
(and snacks) required.
BLACK 5/16" WAFER HEAD SCREW
(8 used in this step)
19
Surface with
holes
Surface without
holes
The holes
should be here.

Step 2
Pae 6
å Fasten the other BACK (G) to the LEFT END (B) and LEFT
UPRIGHT (D). Use eiht BLACK 5/16" WAFER HEAD
SCREWS (19).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
D
B
G
BLACK 5/16" WAFER HEAD SCREW
(8 used in this step)
19
Surface with
holes
Surface without
holes
The holes
should be here.

å Fasten the MODESTY PANEL (I) to the UPRIGHTS (C
and D). Use eiht BLACK 5/16" WAFER HEAD
SCREWS (19).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
Step 3
Pae 7
I
C
D
The tabs should
be located here.
BLACK 5/16" WAFER HEAD SCREW
(8 used in this step)
19

å NOTE: You may need someone's help in this step.
å Fasten the ENDS (A and B), UPRIGHTS (C and D), and
BACKS (G) to the TOP (E). Use twelve BLACK 1-5/8"
WAFER HEAD SCREWS (12).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
Step 4
Pae 8
C
D
A
B
G
G
E
BLACK 1-5/8" WAFER HEAD SCREW
(12 used in this step)
12
Ede with no holes.

å Fasten the SHELF (H) to the LEFT END (B) and LEFT
UPRIGHT (D). Use four BLACK 1/2" WAFER HEAD
SCREWS (15).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
Step 5
Pae 9
D
B
H
BLACK 1/2" WAFER HEAD SCREW
(4 used in this step)
15
The lip should
be facin up.
G
The back ede of the SHELF (H)
should rest aainst the BACK (G).
The arrow
should be here.

å Fasten the BOTTOMS (F) to the ENDS (A and B) and
UPRIGHTS (C and D). Use eiht BLACK 3/4" HEX HEAD
SCREWS (14) and tihten with the L-WRENCH (11).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
Step 6
Pae 10
11
C
D
A
B
F
F
The lip should
be facin up.
BLACK 3/4" HEX HEAD SCREW
(8 used in this step)
14

Step 7
Pae 11
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diaram below. Be
prepared, the parts are reasy.
å Fasten six EXTENSION RAILS (1) to the ENDS (A and B) and UPRIGHTS (C and D). Use twelve BLACK 1/2" MACHINE
SCREWS (16).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in the ENDS and UPRIGHTS. Turn
a SCREW into this hole.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
BLACK 1/2" MACHINE SCREW
(12 used in this step)
16
Push the black lever up and
pull the SLIDE from the RAIL.
12
Use these holes.Open end
C
D
A
B
1
1
1
Open end
1
1Open end
1

å Turn eiht ADJUSTABLE GLIDES (8) into the bottom of
the ENDS (A and B) and UPRIGHTS (C and D).
å NOTE: Turn the ADJUSTABLE GLIDES completely in.
Final adjustments will be made after the unit is
standin upriht.
Step 8
Pae 12
8
A
C
D
B
(8 used)
Now miht be a
ood time to refresh
your drink.

å Push twelve HIDDEN CAMS (3) into the DRAWER
SIDES (L and M) and LARGE DRAWER SIDES (P and Q).
Step 9
Pae 13
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
Arrow
Arrow
3
(12 used)
L
M
P
Q
P
Q

å Turn twelve CAM SCREWS (4) into the exact holes shown
in the DRAWER FRONTS (J and K).
Step 10
Pae 14
4(12 used)
J
K
K

Step 11
Pae 15
1
2
å Fasten the DRAWER SIDES (L and M) to the DRAWER FRONT (J). Tihten four HIDDEN CAMS.
å Slide the DRAWER BOTTOM (O) into the rooves in the
DRAWER SIDES (L and M). å Fasten the DRAWER BACK (N) to the DRAWER SIDES (L and M). Use four BLACK 1-1/2" FLAT
HEAD SCREWS (13).
å NOTE: Be sure the DRAWER BOTTOM (O) inserts
into the roove of the DRAWER BACK (N).
Be sure the
DRAWER
BOTTOM inserts
into the DRAWER
BACK roove.
M
L
23
1
Unfinished
surface
With the palm of your hand,
tap the DRAWER BOTTOM
down into the rooves.
J
BLACK 1-1/2" FLAT HEAD SCREW
(4 used in this step)
13
M
L
ON
M
L
O
Groove
These edes of the
DRAWER SIDES should be
closer to the bottom ede
of the DRAWER FRONT.
J

Step 12
Pae 16
å Fasten two EXTENSION SLIDES (2) to the DRAWER SIDES (L
and M). Use six BLACK 1/2" PAN HEAD SCREWS (17).
å Peel four STICKERS from the APPLIQUE CARD (9) and stick
one onto each HIDDEN CAM in the drawer.
å Fasten the PULL (7) to the DRAWER FRONT (J). Use two
BLACK 3/8" MACHINE SCREWS (18).
7
9
To cover
HIDDEN CAMS
2
Use these holes.
Open end
M
L
J
Open end
Open end
2
2
BLACK 1/2" PAN HEAD SCREW
(6 used for the EXTENSION SLIDES)
17
BLACK 3/8" MACHINE SCREW
(2 used for the PULL)
18
(4 used)

Step 13
Pae 17
å Repeat this step for the other lare drawer.
1
2
å Fasten the LARGE DRAWER SIDES (P and Q) to the LARGE DRAWER FRONT (K). Tihten four HIDDEN CAMS.
å Slide the LARGE DRAWER BOTTOM (S) into the
rooves in the LARGE DRAWER SIDES (P and Q). å Fasten the LARGE DRAWER BACK (R) to the LARGE DRAWER SIDES (P and Q). Use four BLACK 1-1/2"
FLAT HEAD SCREWS (13).
å NOTE: Be sure the LARGE DRAWER BOTTOM (S)
inserts into the roove of the LARGE DRAWER BACK (R).
Be sure the
DRAWER
BOTTOM inserts
into the DRAWER
BACK roove.
Q
P
23
1
Unfinished
surface
With the palm of your hand,
tap the DRAWER BOTTOM
down into the rooves.
K
BLACK 1-1/2" FLAT HEAD SCREW
(8 used in this step)
13
Q
P
SR
Groove
These edes of the LARGE
DRAWER SIDES should be
closer to the bottom ede of
the LARGE DRAWER FRONT.
K
Q
PS

Step 14
Pae 18
å Fasten two EXTENSION SLIDES (2) to the LARGE DRAWER
SIDES (P and Q). Use six BLACK 1/2" PAN HEAD SCREWS (17).
å Peel four STICKERS from the APPLIQUE CARD (9) and stick
one onto each HIDDEN CAM in the lare drawer.
å Fasten the PULL (7) to the LARGE DRAWER FRONT (K). Use
two BLACK 3/8" MACHINE SCREWS (18).
å Repeat this step for the other lare drawer.
7
9
To cover
HIDDEN CAMS
2
Use these holes.
Open end
Q
P
K
Open end
Open end
2
2
BLACK 1/2" PAN HEAD SCREW
(12 used for the EXTENSION SLIDES)
17
BLACK 3/8" MACHINE SCREW
(4 used for the PULLS)
18
(8 used)

å Push two FILE GLIDES (5) onto the LARGE DRAWER
SIDES (P and Q).
å Place two FILE HANGERS (6) onto the FILE GLIDES (5) on
the LARGE DRAWER SIDES (P and Q).
å Repeat this step for the other lare drawer.
Step 15
Pae 19
Q
P
5
56
6

å Carefully stand your unit upriht.
å Peel the BUMPERS from the BUMPER CARD (10) and
stick them onto the front ede of the SHELF (H).
Step 16
Pae 20
Pro Tip: Lift with your
les. And, you know,
your arms.
10
H