Teknik 5426463 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
You could totally write a
novel on this.
Metro Desk
Model 5426463
Teknik
www.teknikoffice.co.uk

No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Skip the power trip.
This time.
Hardware Identification
Part Identification
Assembly Steps
Français
Español
Safety
Warranty
2
3
4-9
10-11
12-13
14
15
åScrews are shown actual size. You may receive extra hardware with your unit.
Hardware Identification
1/2" HEX HEAD SCREW - 14
7
51" MACHINE SCREW  4 1/2" PAN HEAD SCREW - 6 6
L-WRENCH - 1
3WRENCH - 1 42 GLASS SPACER CARD - 1
NUT - 4
1
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C FRAME (2)
D BRACE (4)
E BACK BRACE (1)
F GLASS TOP (1)
G SHELF (1)
A
B
C
C
D
D
D
D
E
F
G
Pae 3

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Fasten the BRACES (D) to one of the FRAMES (C).
Tihten four 1/2" HEX HEAD SCREWS (7) usin the
L-WRENCH (3).
Pae 4
1/2" HEX HEAD SCREW
(4 used in this step)
7
C
D
D
D
D
3

å Fasten the remainin FRAME (C) to the BRACES (D).
Tihten four 1/2" HEX HEAD SCREWS (7) usin the
L-WRENCH (3).
Step 2
Pae 5
1/2" HEX HEAD SCREW
(4 used in this step)
7
C
D
D
D
D
3

å Fasten the SHELF (G) to the FRAMES (C). Use six 1/2"
PAN HEAD SCREWS (6).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
Step 3
Pae 6
1/2" PAN HEAD SCREW
(6 used in this step)
6
C
C
G

Step 4
å Fasten the ENDS (A and B) to the SHELF (G). Tihten six
1/2" HEX HEAD SCREWS (7) usin the L-WRENCH (3).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
Pae 7
These holes must be here.
G
B
A
1/2" HEX HEAD SCREW
(6 used in this step)
7
3

å Fasten the BACK BRACE (E) to the ENDS (A and B).
Tihten four 1" MACHINE SCREWS (5) and four NUTS (1)
usin the WRENCH (4) and a screwdriver.
Step 5
Pae 8
1" MACHINE SCREW
(4 used in this step)
5
(4 used) B
A
E
1
4

å Carefully stand your unit upriht.
å Peel a GLASS SPACER (2) from the GLASS SPACER CARD (2) and stick them onto the tabs of the FRAMES (C).
Step 6
Pae 9www.sauder.com/service426463
2
å Place the GLASS TOP (F) with the shiny surface facin up onto the GLASS SPACERS.
å NOTE: Please read the back paes of the instruction booklet for important safety information.
å This completes assembly. Clean with a damp cloth. Wipe dry.
F
C
C
50 lbs.
35 lbs.

WARNING
Please use your furniture correctly and safely. Improper use can cause safety hazards,
or damae to your furniture or household items. Carefully read the following chart.
Look out for: What can happen: How to avoid the problem:
• Overloaded shelves. • Risk of injury.
• Top-heavy furniture can tip over.
• Overloaded shelves can break.
• Never exceed the weiht limits shown in
the instructions.
• Work from bottom to top when loadin
shelves. Place the heavier items on the
lower shelves.
• Placin TVs on furniture items that are not
desined to support a television is
hazardous.
• Risk of injury or death. TVs can be very
heavy. Plus the weiht and location of the
picture tube tends to make TVs unbalanced
and prone to tippin forward.
• This product is not desined to support a
television.