Teknik 5426133 User manual

Home Study Lateral Filer
Model 5426133
Congratulations. You
are now an adult.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4-5
6-30
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D RIGHT FRONT/LEFT REAR LEG (2)
D61 DRAWER BACK (1)
D87 RIGHT DRAWER SIDE (1)
D88 LEFT DRAWER SIDE (1)
D729 DRAWER BOTTOM (1)
E LEFT FRONT/RIGHT REAR LEG (2)
F FRONT MOLDING (1)
G TOP END MOLDING (2)
H SHELF (1)
J BOTTOM (1)
K UPPER END MOLDING (2)
L LOWER END MOLDING (2)
M END MOLDING (2)
M63 DRAWER BRACE (1)
N BOTTOM MOLDING (1)
O BACK (1)
P BALLAST (2)
Q DRAWER FRONT (1)
A
B
C
D
D
E
E
F
G
G
H
J
K
K
L
L
M
M
N
O
P
P
Q
M63
D61
D87
D88
D729
Pae 3

Hardware Identification
FILE ROD - 2
9B
FILE BAR - 2
1B FILE GLIDE - 2
6B
(EXTENSION SET SHOWN SEPARATED)
EXTENSION SLIDE - 2
40MC
EXTENSION RAIL - 2
40MA
APPLIQUE CARD - 5
100P
ANGLE BRACKET - 7
5G
WASHER - 2
10I
10A SLIDE CAM - 2
CAM SCREW - 9
8F
PULL - 2
22K
WOOD DOWEL - 6
15F
FILE BRACKET - 2
12B HIDDEN CAM - 24 1F CAM DOWEL - 15 2F
Pae 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" LARGE HEAD SCREW - 14
1S
BROWN 7/16" LARGE HEAD SCREW - 4
6S
SILVER 1/4" MACHINE SCREW - 2
61S
100S BLACK 2-3/4" FLAT HEAD SCREW - 4
BLACK 9/16" FLAT HEAD SCREW - 12
32S
BLACK 1-15/16" FLAT HEAD SCREW - 3
113S
30S BLACK 1-9/16" FLAT HEAD SCREW - 5
3S GOLD 5/16" FLAT HEAD SCREW - 8
Pae 5

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratchin your unit or the floor.
å Turn six BLACK 9/16" FLAT HEAD SCREWS (32S) into the LEFT END (B) until the shoulders of the SCREWS rest on the
surface of the LEFT END.
å NOTE: Do not overtihten the SCREWS.
å Slide the UPPER END MOLDING (K) onto the LEFT END (B). Line up the roove in the MOLDING over the heads of the
SCREWS in the LEFT END.
å NOTE: If the MOLDING comes up o of the SCREWS, remove it and slide it on aain.
å Slide the END MOLDING (M) onto the LEFT END (B) until it is aainst the UPPER END MOLDING (K). Line up the roove in
the MOLDING over the heads of the SCREWS in the LEFT END.
å NOTE: If the MOLDING comes up o of the SCREWS, remove it and slide it on aain.
These edes
should be even.
B
K
M
BLACK 9/16" FLAT HEAD SCREW
(6 used in this step)
32S
Shoulder
Apply pressure with your hands
as you uide the MOLDINGS over
the SCREWS and onto the ENDS.
Apply pressure with your hands
as you uide the MOLDINGS over
the SCREWS and onto the ENDS.
Shoulder
Pae 6

Step
å Slide the LOWER END MOLDING (L) onto the LEFT END (B).
Line up the roove in the MOLDING over the heads of the
SCREWS in the LEFT END.
å NOTE: The MOLDING should be even on both edes of the END.
å NOTE: If the MOLDING comes up o of the SCREWS, remove it
and slide it on aain.
Step 2
BL
Shoulder
Apply pressure with your hands
as you uide the MOLDINGS over
the SCREWS and onto the ENDS.
Pae 7
Just think. The sooner
you do this, the sooner
you do somethin else.

Hardware Usage Guide
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3. Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
HOW TO USE A HIDDEN CAM & CAM DOWEL
Hole
Hidden Cam
Cam Dowel
2.
Hole
Hidden Cam
Cam Dowel
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Metal end
Arrow
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
ede of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tihten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is aainst the
surface of the part.
1.
Pae 8

å Turn four CAM SCREWS (8F) into one set of the LEGS (D and E) as
shown in diaram 1
å Insert two WOOD DOWELS (15F) into the LEGS (D and E) as shown
in diaram 1.
å Flip over the LEGS (D and E) as shown.
å Push two HIDDEN CAMS (1F) into the LEGS (D and E) as shown
in diaram 2. Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
Step 3
D
D
E
E
F
L
I
P
O
V
E
R
F
L
I
P
O
V
E
R
8F
8F
15F
15F
Do not tihten the HIDDEN CAMS in this step.
Arrow
1F
2F
(2 used)
Metal end
1
2
1
2
Pae 9

å Push four HIDDEN CAMS (1F) into the LEFT END (B).
å Fasten the LEGS (D and E) to the LEFT END (B). Tihten
four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEGS insert
into the RIGHT END.
Step 4
B
B
E
D
1F
Arrow
1F
Arrow
Anled ede
Anled ede
Pae 10