Teknik Barrister Home Lift Up 5420329 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
www.teknikoffice.co.uk
Barrister Home Lift Up Coffee Table
Model 5420329
It's addicting.
Teknik

Table of Contents Assembly Tools Required
3
4-5
6-23
Part Identification
Hardware Identification
Assembly Steps
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A UPPER RIGHT END (1)
B UPPER LEFT END (1)
C LOWER END (2)
D UPRIGHT (1)
E TOP (1)
F BOTTOM (1)
G SHELF (1)
H LONG SKIRT (2)
I SIDE SKIRT (2)
J BRACE (1)
K LONG MOLDING (2)
L TOP END MOLDING (2)
M END MOLDING (4)
N UPRIGHT MOLDING (2)
O PANEL (2)
P PLINTH (4)
Now you know
our ABCs.
Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
P
P
P
C
K
L
M
M
M
N
H
I
O

Hardware Identification
åYou may receive extra hardware with your unit.
31G CORNER BRACKET - 4
23M LIFT TABLE
MECHANISM SET - 1
SUPPORT BRACKET - 2
37G
NUT - 8
24M
WASHER - 8
13M
METAL BRACKET - 4
4G
10F TWIST-LOCK®
FASTENER - 10
MOLDING
CONNECTOR - 4
17F
BUMPER - 6
2M
WOOD DOWEL - 2
15F
HIDDEN CAM - 12
1F CAM DOWEL - 12 2F
Page 4
CAM COVER - 12
13P
BUSHING - 2
91M

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 5
BLACK 9/16" LARGE HEAD SCREW - 48
1S SILVER 1-1/8" FLAT HEAD SCREW - 8 10S
BLACK 3/4" PAN HEAD SCREW - 2
85S BLACK 3/4" MACHINE SCREW - 4
92S
BLACK 1-1/4" MACHINE SCREW - 4
93S BLACK 1-15/16" FLAT HEAD SCREW - 14
113S

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (10F) into the large holes in the UPPER
ENDS (A and B) and PANELS (O).
Page 6
10F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
A
B
O
O
(10 used)

Step
Page 7
Step 2
å Push twelve HIDDEN CAMS (1F) into the UPPER ENDS (A and B),
LOWER ENDS (C), and UPRIGHT (D). Then, insert the metal end
of a CAM DOWEL (2F) into each HIDDEN CAM.
A
B
C
D
C
(12 used)
Arrow
1F
2F
Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Some assembly
(and snacks) required.

Step
å Tap four MOLDING CONNECTORS (17F) into the notches
in the MOLDINGS (K and L).
Step 3
Page 8
Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the MOLDINGS.
KL
K
L
Curved edge
17F
17F
17F
17F
Flat end
Flat end

Step
Page 9
Step 4
å Fasten the UPPER ENDS (A and B) to the PANELS (O).
Tighten four HIDDEN CAMS.
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
O
B
A
Surface with
HIDDEN CAMS
O
Edge with
TWIST-LOCK®
FASTENERS
Edge with
TWIST-LOCK®
FASTENERS
Surface with TWIST-LOCK® FASTENERS
Surface without TWIST-LOCK® FASTENERS

Step
å With someone's help, flip the UPPER ENDS (A and B) and PANELS (O) over.
å Fasten the UPPER ENDS (A and B) and PANELS (O) to the MOLDINGS (K
and L). Tighten ten TWIST-LOCK® FASTENERS.
Step 5
Page 10
O
B
A
O
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
K
L
K
L
Curved edge